
TH-PT24
Installation Instructions
Projector | Suspended Ceiling Tile 24"
Component Checklist
Hardware
Safety Wire
Tools Required:
Phillips head screwdriver
Wire cutters
Power drill
1
6mm (
/4”) drill bit
6mm (1/4”) masonry drill bit
Claw hammer
Jigsaw/Hole cutter
Spirit level
Cover Plate
Suspended
Ceiling Tile
1.5” NPT
Mounting
Collar
Pole Lower
Mounting Plate
1.5” NPT Upper
Mounting Plate
IMPORTANT INFORMATION:
! IMPORTANT - Install Telehook Projector - Suspended Ceiling Tile 24" as per Installation Instructions.
! This product supports 1.5” NPT Pole Mounts, Atdec Pole Mount (TH-WH-PJ-CM), and Atdec Flush Mount (TH-WH-PJ-FM).
! Maximum weight capacity 22.7kg (50lbs).
! The manufacturer accepts no responsibility for incorrect installation.
Support Wire
Pole Upper
Mounting Plate
1.5” NPT Lower
Mounting Plate
M6 Washer
(x8)
Safety Clamp
(x2)
Lag Eye
Bolt (x4)
Concrete
Anchor
3mm
Allen Key
M6 Wing
Nut (x4)
Bolt (x4)
Turnbuckle
(x4)
M6 Set
Screw (x2)
M6x16mm
Screw (x4)
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Remove Existing Ceiling Tile
Remove existing ceiling tile from ceiling grid where the product
is going to be installed.
TIP: Also temporarily remove an adjacent ceiling tile to allow easy
access to the product during installation.
Step 3. Fix Anchors to True Ceiling
Uncoil Support Wire and cut into 4 equal lengths. Select the anchoring method appropriate to your ceiling (see below).
NOTE: Each anchor point should be directly above each corner of the Suspended Ceiling Tile.
Wooden Joists
Drill 4x Ø6mm holes, at least 50mm deep
(4x ؼ” holes, 2”deep).
Fully screw Lag Eye bolts into wooden joists.
Wooden
Joist
Solid Concrete
Drill 4x Ø6mm holes, 36mm deep
(4x ؼ” holes 1½” deep).
Tap anchors into hole to an embedded depth
of at least 25mm deep (1” deep).
Using a claw hammer, pull anchor out 6mm
”
) to activate anchor.
(¼
OR
Solid
Concrete
Truss Beams
Thread one end of Support Wires through the
trusses, and wrap 5 times to secure.
OR
Lag Eye Bolt (x4)
Support Wire (x4)
Thread one end of each support wires through
a Lag
Eye Bolt, and wrap 5 times to secure.
Concrete Anchor
Bolt (x4)
Support Wire (x4)
Thread one end of each support wires through
a Lag
Eye Bolt, and wrap 5 times to secure.
Step 4. Attach Turnbuckles onto Support Wires
Support
Wire (x4)
Turnbuckle
Hooks
Turnbuckle
(x4)
Truss Beam
Support
Wire (x4)
Loop each dangling Support Wire through a Turnbuckle, and wrap
5 times to secure.
Make sure that the position of the x4 Turnbuckles are approximately
at the same height.
TIP: The turnbuckle hooks should be level with the top of ceiling grid.

Step 5. Assemble Projector Mount Interface onto Suspended Ceiling Plate
1.5” NPT Bracket (included) Atdec Flush Mount
M6 Set
Screws (x2)
3mm
Allen Key
M6 Washer
(x4)
Wing Nuts
(x4)
Atdec Pole Mount
(TH-WH-PJ-CM supplied separately)
M6 Washer
(x4)
Wing Nuts
(x4)
Pole Upper
Mounting Plate
(TH-WH-PJ-FM supplied separately)
M6 Washer
(x4)
OROR
Cover Plate
Cover Plate
1.5” NPT
Mounting Collar
(optional for 1.5”
projector heads only)
1.5” NPT Lower
Mounting Plate
Step 6. Hook Suspended Ceiling Tile
Hook Suspended Ceiling Tile to the Turnbuckles.
Twist Turnbuckles for height adjustment.
The Suspended Ceiling Tile should sit flush in ceiling grid.
Pole Lower
Mounting Plate
Step 7. Fix Safety Wire
Thread one end of the Safety Wire through
a Lag Eye Bolt, Concrete Anchor, or Truss
and clamp using Safety Clamp.
TH-WH-PJ-FM
Ceiling Plate
Wing Nuts
(x2)
Cover Plate
M6x16mm
Screws (x2)
TWIST
TIP:
Use a spirit level to ensure
the Suspended Ceiling Tile is level.
Step 8. Install Projector Mount and Ceiling Cover
1.5” NPT Pole Mount
(supplied separately)
Atdec Pole Mount
(TH-WH-PJ-CM supplied separately)
OR
SCREW
PUSH
Safety Clamp
TIGHTEN
2x NUTS
Safety
Wire
Thread other end of Safety Wire
through the Suspended Ceiling Tile
and clamp using Safety Clamp.
(choose Ceiling Cover to suit projector mount)
Atdec Flush Mount
(TH-WH-PJ-FM supplied separately)
OR
PUSH
TIGHTEN
2x NUTS
Installation Complete - Ready to install Projector
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 31.03.11©