Atdec TH-CM-SH-2 Installation manual

Page 1
Installation Instructions
TELEHOOK
Cable Manager Shelf System
TM
Component Checklist
Bits Bag
Shelf (x2)
Check you have received
all parts against the
Component Checklist
Screw (x8)
2mm Allen Key
IMPORTANT NOTES
The Telehook Cable Manager Shelf System MUST be used in conjunction with the Telehook Cable Manager.
Each Telehook Cable Manager is limited to a maximum of 4 Shelves.
Each Shelf supports a maximum weight of 20kgs (44lbs).
If you wish to paint your Cable Manager Shelves, please consult your paint specialist for advice.
A Installation Options
If your display is already wall mounted, depending on its position, it may be best to remove the display, as it may interfere with the installation of the Telehook Cable Manager and Cable Manager Shelf System.
Option 1
If you already have the Telehook Cable Manager installed.
Begin by removing the Front Fascia and the End Caps as shown. Once complete, continue to step B below.
Push one edge of the Front Fascia until it pops open
Remove End Caps
OR
Option 2 If you are installing both
the Telehook Cable Manager and Telehook Cable Manager Shelf System at the same time.
Begin by mounting the Wall Plate as shown in step A on the Telehook Cable Manager Installation Instructions. Once complete, continue to step B below.
Cable Manager, you may need to reduce
B Installing Telehook Cable Manager Shelves
B.1.
Slide the Cable Manager Shelf onto the Cable Manager Wall Mount
TOP VIEW
B.2.
Adjust the Cable Manager Shelf to the desired height
Note:
If the mounted height of the display is
less than the length of the Telehook
the length by cutting it to size.
(Consult a professional at this stage)
B.3.
Secure in place using the M4 Grub Screws and the 2mm Allen Key supplied
Page 2
C Install your Equipment
Install or reinstall your display Place your Audio/Video equipment on the Telehook Cable Manager Shelves Connect all required cables to Audio/Video equipment
D Installing Cables
Display on
wall mount
bracket
Wall Plate
Shelf
NOTE:
If possible, separate the display’s
power cable from the data cables (i.e. hi-fi & speaker cables) by installing them into separate cable bays. This will reduce the chance of electromagnetic interference. The diagram to the right shows an example installation setup.
Install the display’s cables into the left,
right and centre cable bays as shown
Data cables
(can also be installed
into the same bay)
TOP VIEW
Left cable bay
(best for display power cable)
Centre cable bay
Display Power
cable
Right cable bay
E Insert Cable Clips
Insert the Cable Tabs into
the Wall Plate to Secure
Cable
Ta b
E.2.
Twist the Cable Tabs into the small slots in the Wall Plate
If required, cables can exit from the side of the Cable
Manager. In this case, use the left or right cable bays
Cables exiting from the side
E.1.
Using your thumb and index finger, flex the Cable Tab into a concave shape
Cables in place.
only.
F Attach End Caps
End Cap Cable Bay
TOP VIEW
Using two hands,
flex the End Cap
display’s cables
and manoeuvre
corresponding End
Attach an End Cap onto
both ends of the Wall
Plate and secure in place
using the M4 Grub
M4
Grub
Screw
WARNING: DO NOT OVER TIGHTEN
2mm Allen
Key
around the
them into their
Cap Cable Bay
Screws as shown.
G Insert Front Fascia
G.1.
Slide the Front
Fascia through the
cut outs in the
Shelves
G.3.
Push the edge of the Front Fascia until it snaps into place
TOP VIEW
A
B
G.2.
Partially insert the front fascia as shown above
G.4.
Repeat G.3.
down the
length of the
Front Fascia
until it is firmly
secured onto
the Wall Plate
Installation Complete
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 24.09.07©
Loading...