TH-AN-CM
Installation Instructions
TELEHOOK
IMPORTANT NOTES
It is recommended that your display be installed prior to the installation of this product.
If you wish to paint your Cable Manager, please consult your paint specialist for advice.
Surface finish: Clear Anodised Aluminium
TM
Cable Manager
Component Checklist
Front Fascia
End Cap (x2)
(Check you have received all parts against the Component Checklist below)
Wall Plate
Tools Required: Power drill 4mm (3/16”) drill bit 6mm (1/4”) drill bit Phillips head screwdriver
A Mount the Wall Plate
Timber Stud Wall
Timber Stud
Wall Plate
10g x 30mm
screw
Masonry
OR
End Profile
End Profile
Nylon Wall Plug
Bits Box
10g x 30mm
Screw (x4)
Nylon Wall
Plug (x4)
10g x 30mm
screw
Dry Wall
OR
Cable Tabs (x8)
M4 x 5mm Grub
Screw (x4)
Dry Wall
2mm Allen Key
Dry Wall
Anchor (x6)
Dry Wall Anchor
Screw
Masonry
Wall
4mm (3/16”)
hole
Mounting
Hole
Pattern
6mm
(1/4”)
hole
Mounting
Hole
Pattern
To determine the best position for your Cable Manager, see “Mounting Tips” below
IMPORTANT: Ensure the lower edge of the Wall Plate is positioned no less than 50mm
(2”) above the skirting board so that there is enough room to accommodate the End Cap
Mounting Tips:
Telehook Cable Manager has been designed to hide the cables of a wall mounted display.
Therefore, it is recommended that it is mounted vertically and centrally below your display.
The adjoining image shows a typical Cable Manager installation.
Ideally, the top of Telehook Cable Manager should sit just under the lower edge of your display
with the bottom of Telehook Cable Manager (i.e. the End Cap) sitting approximately 50mm (2")
above the floor or skirting board.
6mm
1
/4”)
(
hole
Dry
Wall
Anchor
Mounting
Hole
Pattern
IMPORTANT: For Dry Wall Installation
use alternating mounting holes
Display
Te le h o ok
Cable
Manager
Optional Shelf
(sold separately)
End Cap
B Mount your Display
Mount your display onto its wall mount bracket
Connect all the required cables to the display and if necessary, manoeuvre it into its final viewing position
C Installing Cables
Display on
wall mount
bracket
Wall Plate
NOTE:
If possible, separate the display’s
power cable from the data cables
(i.e. hi-fi & speaker cables) by
installing them into separate cable
bays. This will reduce the chance of
electromagnetic interference. The
diagram to the right shows an
example installation setup.
Install the display’s cables into the left,
right and centre cable bays as shown
Data cables
(can also be installed
into the same bay)
TOP VIEW
Left cable bay
Centre cable bay
(best for display power cable)
Display Power
cable
Right cable bay
D Insert Cable Clips
Insert the Cable Tabs into
the Wall Plate to Secure
Cable
Ta b
E.2.
Twist the Cable
Tabs into the small
slots in the Wall
Plate
If required, cables can exit
from the side of the Cable
Manager. In this case, use
the left or right cable bays
Cables exiting from the side
E.1.
Using your
thumb and
index finger,
flex the Cable
Tab into a
concave shape
Cables in place.
only.
E Attach End Caps
End Cap Cable Bay
TOP VIEW
Using two hands,
flex the End Cap
and manoeuvre
corresponding End
Attach an End Cap onto
both ends of the Wall
Plate and secure in place
using the M4 Grub
M4
Grub
Screw
2mm
Allen
WARNING: DO
NOT OVER TIGHTEN
Key
around the
display’s cables
them into their
Cap Cable Bay
Screws as shown.
F Insert Front Fascia
F.2.
Push the edge of the
Front Facia until it snaps
into place
B
Front Fas ci a
TOP VIEW
A
F.1.
Partially insert the
front facia as shown
F.3. Repeat F.2.
down the length
of the Front Facia
until it is firmly
secured onto the
Wall Plate
Installation Complete
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 02.03.12©
Loading...