C
Attaching the Display to the Wall Plate
C.1. Attaching the Display to the Wall Plate
Note: This procedure will require two persons
C.2. Pivot Head Load Capacity Adjustment
M12 Hex Nut
Tighten
Installation Instructions
TELEHOOK
TH-30-50-RW /
Important Notes
The Telehook 30-50 Universal Rotating Wall Mount supports flat panel displays from 30” (76cm) to 50” (127cm)
and supports a maximum load of 85kgs (187lbs).
This product is factory set to support 35kgs (77lbs), and will need to be adjusted if the display is heavier or lighter.
30”-50” UNIVERSAL ROTATING WALL MOUNT
Back Plate
Mounting
Slots
Note: For demonstration purposes, the wall
has been omitted from the above image.
With the mount attached to the display, lift the
display and slide the Back Plate into the Mounting
slots to ensure a secure connection.
D
Security Option
Note: For demonstration purposes, the display
has been omitted from the image below.
Back plate
Padlock
Adjusting the Pivot Head to suit the weight of the
Display
The Pivot head is factory set to hold
approximately 35kgs (77lbs). If the display is not
holding its position when placed on the wall it
may be necessary to remove the display from
the wall and tighten the M12 Hex Nut on the
back of the Pivot Head using a 17mm (
11
/16”)
socket wrench or shifter. To achieve a one-touch
effortless adjustment setting it is advised that the
nut be tightened at half turns and re-tested, until
the desired friction is achieved. Alternatively the
M12
Hex Nut can be over tightened in order to
lock the display in position.
For additional security,
it is suggested that a
Padlock be attached to
the Back plate as shown.
The Padlock (not supplied)
should have a shackle
diameter no larger than
3
/
”).
16
Mounting Slot
Shackle 4mm (
diameter or less
4mm (
3
/
”)
16
The manufacturer does not accept responsibility for incorrect installation.
Component Checklist
Extension Plate
Pivot Head
Bracket Plate (x2)
TOOLS REQUIRED:
Power Drill
12mm or 8mm Drill Bit
Phillips Head Screw Driver
Spirit Level
17mm (11/
”) Socket Wrench
16
or Shifter
A
Mounting the Wall Plate
Masonry Wall
Masonry
Wall Plug
12mm (
Hole
1
/2”)
Wall Plate
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
Bracket (x2)
Wall Plate
Timber Stud Wall
Note: It is recommende d to
mount the Wall Plate by firmly
fixing the four Coach Sc rews
into two studs. However, if the
weight of the display is less than
50kgs (110lbs), it is possible to
mount the Wall Plate to one stud
by fixing the two Coach Sc rews
through the two Cent re holes.
Bits Box
Coach
Screw (x4)
Spacer
Bush (x4)
Allen Key
Small
Washer (x4)
Masonry Wall
Plug (x4)
Large
Washer (x4)
M6x16mm Socket
Drive Screw (x12)
Multi
Washer (x4)
TIP: Use a spirit
level to ensure the
Timber
Stud
Centre Holes
Mounting
Screws
M8x20mm
Phillips Head
Screw (x4)
M6x16mm
Phillips Head
Screw (x6)
M5x16mm
Phillips Head
Screw (x6)
M4x16mm
Phillips Head
Screw (x6)
wall plate is
horizontal
8mm (5/
16
Hole
”)
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 02.05.12 ©
Note: Ensure the Wall Plate
is mounted with the narrow
end of the Mounting Slot
at the bottom.
Coach Screw
Large Washer
Note: Ensure the Wall Plate is
mounted with the narrow end of the
Mounting Slot at the bottom .
Coach Screw
Large
Washer
B
Choosing and Assembling the Correct Mounting Configuration
Measure the mounting hole pattern on the back of the display. Select the appropriate configuration (either 1, 2
or 3) that best suits the mounting hole pattern of the display then attach the product to the display as shown.
Configuration 1: VESA Compliant 100mmx100mm (4”x4”) & 100mmx200mm (4”x8”)
Mounting Hole Patterns
Mounting Screw
Back
of Display
Note: The
100mmx200mm
mounting
configuration is
shown. For mounting
displays with
100 mm x10 0mm
mounting hole
patterns, use the
100 mm x10 0mm h oles
in the Pivot Head.
100 mm
ii
(4”)
100 mm
(4”)
100 mm
(4”)
200mm (8” )
Pivot Head
Top of
Display
Configuration 3: 260mm to 660mm (101/
Mounting Hole Patterns
260mm
1
/4”)
(10
400mm
3
/4”)
(15
660mm (26”)
Pivot Head
-26”) x 200mm to 400mm (8”-15
”
4
Attaching the Bracket to the Display
M4 & M5
Screw Hole
Multi Washer
200mm
(8”)
In orde r to ensure the dis play is s ecure ly attached to the
bracke t it is rec ommen ded that the br acket b e fastened wi th the
mounting screws align ed alon g the bottom e dge of th e slots.
It is also impor tant t hat you use the supplie d Multi Wa sher an d
ensure t hat the tightest fittin g hole in t he wash er is use d for the
specific size screw
Slot
3
/4”)
M6 Socket
Drive Screw
M6 Screw
Hole
M8 Screw
Hole
Configuration 2: 200mmx200mm to 400mm (8”x8”-153/4”) Mounting Hole Patterns
Note: If the display has a vertical
mounting distance of 200mm and
requires the use of the M6 Mounting
Screws, it will be necessary to
Back
of Display
200mm
(8”)
substitute the MuIti Washers for the
400mm
200mm
Mounting
Screw
Multi Washer
Bracket
Plate
Note : When a ssemb ling t he prod uct,
ensur e the re d Telehoo k Badg es are
positioned towards the bottom of the display
(8”)
3
/4”)
(15
Pivot Head
small washers provided.
M6 Socket
Drive Screw
Tele hook
Badge
M6 Mounting
Screw
Display
Top of
Bracket
Small
Washer
Extension
Plate
Tele hook
Badge
Spacer Bush
Spacer Bush Assembly
If the mounting holes are recessed into the
back of the display, use the supplied Spacer
Bushes to pack the recessed hole and ensure
that the bracket is securely fixed to the display.
Back
of Display
Mounting Screw
Multi Washer
Bracket
Top of
Display
Recessed Hole
Note : When a ssemb ling t he
produ ct, ens ure th e Telehoo k
Badge s are po sitio ned tow ards th e
botto m of the d ispla y
Spacer Bush
Bracket
Plate
Mounting
Screw
Multi Washer
Loading...