Step 7. Mounting the Display onto the Articulated Arm
Lower the Display so that the Hook
Plate locates with the Mounting
Head.
Hook
Plate
If necessary, adjust the horizontal
angle of the Mounting Rail so that
the Display is level.
+/-5°
Adjustment
( required)
TH-3270-UFM
Installation Instructions
TM
Fix the Display in position using the
Mount Head Screw and Nylon
Washer supplied (see hardware).
5mm
Allen Key
Component Checklist
TIGHTEN
FIRMLY
Flat Screen Wall Mount | Full Motion
Mounting Rail
Hardware
Mounting
Head
Step 8. Cable Management
Connect cables to your Display and
route through Cable Clips.
Cable Clip
Cables
Step 9. Final Adjustment
Loosen screw with 5mm Allen key
and tilt the Display as desired.
LOOSEN
TIP: Use a Spirit Level to
Nylon
Washer
Mount
Head Screw
check the Display is level.
Remove Cable Covers using a Phillips Head Screwdriver, and route
the cables along the length of the arms. Reattach the Cable Covers
to hold the Cables in place.
TIP: Leave slack in the
cables to allow full
movement at the joints.
Tighten screw with 5mm allen key
to lock the Display in desired position.
Cable Covers
TIP: The 5mm and 6mm
Allen Keys can be stored
in the Mounting Rail End
Tilt Down
Caps.
Mounting
M10 Coach
Screw (x3)
Concrete
Anchor (x3)
5mm/6mm
Allen Key
Bracket (x2)
Articulated Arm
Drilling Guide
TOOLS REQUIRED:
• Power Drill
• Phillips Head Screwdriver
• Flat Blade Screwdriver
• Spirit Level
• 7mm (
9
/32”) Drill Bit
• 12mm (½”) Masonry Drill Bit
• 16mm (5/8”) Socket Wrench or Shifter
M5 Washer
(x4)
M10 Washer
(x3)
Mounting Screws
M6 Washer
(x4)
M4/5 Spacer
Bush (x4)
M8 Washer
(x4)
M6/8 Spacer
Bush (x4)
M8x30mm / M8x50mm (x4 each)
M6x30mm / M6x45mm (x4 each)
M5x30mm / M5x45mm (x4 each)
Mount Head
Screw
Nylon
Washer
IMPORTANT INFORMATION
! IMPORTANT - Install Telehook Wall Mount as per Installation Instructions.
! Telehook Wall Mount has a universal mounting hole pattern that suits a broad range of TVs:
from150 to 805mm wide (6” to 31¾”) and 140mm to 500mm high (5½” to 19¾”).
! Maximum Load: 65kg (143lbs)
! The Manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Locate Drilling Position
Choose the location of your Telehook Wall Mount, ensuring that the wall is structurally sound (for a timber stud
wall, locate the stud using a stud detection device). Use the Drilling Guide to mark out the hole centres.
TIGHTEN
End Cap
5mm Allen key
Installation Complete
As Display Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 15.05.12 ©
Tilt Up
Top
Drilling Guide
FRONT
Dust Collector
Un-fold the Drilling Guide and
open the Dust Collector.
Drilling Guide
BACK
Double-sided
tape (x2)
Peel away the backing from the
double-sided adhesive tape.
WALL
Position the Drilling Guide vertically
onto the wall using a spirit level.
Step 3. Attaching the Articulated Arm to the Wall
Remove the Telehook Arm from
the packaging and open fully.
ROTATE
Timber Stud Wall
- Using the Drilling Guide, drill three 7mm (
diameter holes, 60mm (2
- Secure the Mouting Plate to the wall using the Coach
Screw and Washers supplied.
3
/8”) deep.
9
/32”)
Wall Plate Cover
Masonry Wall
- Using the Drilling Guide, drill three 12mm (½”)
diameter holes, 60mm (2
- Secure the Mouting Plate to the wall using the Coach
Screw, Washers and Anchors supplied.
Cover and slide down the arm.
Un-clip the Wall Plate
3
/8”) deep.
Step 5. Landscape or Portrait Setup
NOTE: The Mounting Rail is factory set to mount the Display in a landscape position.
If you wish to mount the Display in a portrait position, please carry out the following instructions (if not, skip to Step 6).
Remove the:
• Cover Plate.
• Two Button Head Screws using the
5mm Allen Key supplied.
Loosen, but do not remove the
Centre Pin using the 6mm Allen Key
supplied.
Rotate the Hook Plate 90°,
Remove the lower Cable Clip.
Then reinstall the two Button Head
Screws and Cover Plate.
then re-tighten the Centre Pin.
ROTATE 90°
Hook
Plate
Cable Clip
Cover
Plate
LOOSEN
Timber
Stud
OR
Coach Washer
M10 (x3)
Step 4. Attaching the Mounting Brackets to your Display
Choose appropriate Mounting Screws and Washers
from the Hardware supplied to suit your Display.
Mounting Screws (x4)
Coach Screw
M10 (x3)
Washers (x4)
Mounting
Bracket
Top o f
Display
Masonry
Wall
Concrete
Anchor (x3)
Coach Bolt
M10 (x3)
Coach Washer
M10 (x3)
Recessed Mounting Holes or
Display with a Curved Rear Panel
If the Mounting Holes are recessed
into the back of the Display, or the
Display has a curved rear panel, use
the appropriate Spacer Bushes
supplied to pack the Mounting Holes.
NOTE: Ensure the Mounting Bracket
is securely fixed to the Display.
Mounting
Screw
Washer
5mm
Allen Key
Centre
Pin
TIP: Use a small Flat Blade
Screwdriver to help prise the
Cover Plate loose.
LOOSEN
TIGHTEN
6mm Allen Key
Step 6. Attaching the Mounting Rail to the Mounting Brackets
Remove the Locking Plate from
each Mounting Bracket using the
Slide the Mounting Rail under
both Mounting Brackets.
5mm Allen Key supplied.
Mounting
Bracket
Locking
Plate
Mounting
Rail
PUSH
TIGHTEN
FIRMLY
Centralise the Mounting Rail on
the Display, then reinstall the
Locking Plates to clamp the
Mounting Rail in position.
CENTRE
Mounting
Bracket
Mounting
Back of Display
Hole
TIP: Secure the Mounting Bracket to the Display
through the top hole first, then the bottom slot.
Spacer
Bush
Mounting
Hole
5mm
Allen Key
LOOSEN
Mounting
Bracket
PUSH
Locking
Plate
5mm
Allen Key
TIGHTEN
FIRMLY
Loading...