Atdec TH-31-55-SA-PK Installation manual

G Fix the Tilt angle of the Display

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 29.08.08 c

Step 1

Fit two M8x45mm Locking screws
into brackets behind Display. Adjust
the Tilt angle of the Display. Tighten
two locking screws with the Long
6mm Allen Key provided.

WARNING: Do not attempt to
adjust tilt angle without firstly
loosening locking screws.
Doing so may damage
product.

M8 Small

Washer

M8x45mm

Screw

Long 6mm

Allen Key

Tighten

TM

A Attach Telehook Swing Arm Unit to the Wall

NOTE:

The manufacturer does
not accept responsibility
for incorrect installation.

Telehook Flat Screen

Wall Mount Swing Arm

supports a maximum

weight of 65kgs (143lbs)

TOOLS REQUIRED:

z Power Drill
z 12mm (1/2”) Drill Bit
z 7mm (9/32”) Drill Bit
z Adjustable wrench

12mm (1/2”) hole

Wall Plug

Tip: Use a Spirit

Level to ensure

this surface is

vertical.

M10 Coach Screw

M10 Steel Washer

Masonry Wall

OR

Timber Stud Wall

Timber Stud

M10 Coach Screw

Tip: Use a Spirit

Level to ensure

this surface is

vertical.

M10 Steel Washer

7mm (9/32”) hole

.

.

H Horizontal Adjustment Feature

TIGHTEN

LOOSEN

If necessary, once the display is mounted, adjust the horizontal
angle as shown.

ADJUST

ANGLE

-5° to 25°
Tilt

Padlock

(not supplied)

5mm (3/16”)

diameter shackle

For added security, you may
choose to attach a padlock
to one or both brackets to
prevent theft of the display.
It is recommended that the
padlock should have a
shackle diameter of 5mm
(3/16”).

I Security Option

Component Checklist

Wall Mount Horizontal Bar

Wall Mount Bracket (Left)

Wall Mount Bracket (Right)

Slider (x2)

5mm

Allen Key

M10 Steel

Washer (x4)

M8 x45mm

Locking Screws (x2)

Multi

Washer (x6)

M5 x16mm

Mounting

Screws (x6)

M6 x16mm

Mounting

Screws (x6)

M8 x16mm

Mounting

Screws (x6)

M10 Coach

Screw (x4)

M4 x16mm

Mounting

Screws (x6)

Bit Box

IMPORTANT:

Ensure you have received all parts against the component checklist prior to installing.

Clinch Nuts

M12 Steel

Washer

M12 Plastic
Washer (x2)

M12 x80mm

Screw

M12

Locking Nut

Cable Manager

Clip (x4)

8mm

Allen Key

Long 6mm

Allen Key

Wall Mount

Cover

Telehook Swing Arm

Pivot Head

Installation Instructions

Flat Screen Wall Mount | Swing Arm

M8 x45mm

Button Screws (x2)

M8 Small

Washer (x2)

Wall Plug (x4)

D Positioning Sliders

Step 1

Accurately position sliders at distance X as recorded in Section A. Ensure the Sliders are equally spaced along the centre Horizontal
Bar.

=

=

Slider (x2)

Grub

Screws (x2)

Step 2

Secure slider in
position and tighten
firmly with supplied
Allen Key. Ensure that
it locates into the slot
on the horizontal bar.
The grub screw should
tighten flush to
surface.

C Attaching the Brackets to the Display

M8 Screw Hole

M6 Screw Hole

M5 & M4

Screw Hole

Step 2:

Use the supplied Multi Washer as
shown above. Ensure that the tightest
fitting hole in the washer is used for
the specific sized screw. Note

distance X, for use in the
following steps.

=

=

TOP

Clinch Nuts

Multi Washer

Step 1

Attach left and right wall mount brackets to the rear of your display. Select M4, M5, M6 or M8 mounting screws to suit your display.
Ensure a minimum of two mounting screws are used per wall mount bracket. Clinch nuts must be positioned as shown (internally).

B Attach Pivot Head to Swing Arm

Step 1

Slide the Wall Mount Cover along the
Swing Arm until it snap fits onto the
wall plate.

Wall Mount Cover

Step 2

Assemble the Pivot Head
onto the Swing Arm as
shown.

M12 Screw

M12

Locking Nut

M12 Steel

Washer

M12 Plastic

Washer

Wall Plate

End of

Swing Arm

E Attach the Horizontal Bar to Pivot Head

Step 1

Attach the Horizontal Bar and tighten
screws as shown.

M8x45mm

Button Screws

Pivot Head

Horizontal Bar

Step 1

Note: This operation
requires two persons.

Now that the horizontal bar is
attached to the Swing Arm
with the Sliders in place, lift
the Display with brackets
attached and hook the
Brackets over the Sliders.

Note: The brackets should
rest on the horizontal bar
with the slider between the
bracket.

F Mounting the Display

Cable

Manager Clips

Step 2

Attach the four Cable Manager Clips to
the Swing Arm by inserting the clips into
the holes. Ensure that the clips are held
firmly in place.

Swing Arm

X

Tighten

Distance X

Horizontal Bar

8mm Allen

Key

5mm Allen

Key

Note: make sure
the threaded nut
faces inwards