Page 1
Installation Instructions
FLAT SCREEN WALL MOUNT | FIXEDTH-3070-UF
Important Notes
Supports a maximum load of 91kgs (200lbs).
Suits displays with mounting hole patterns from 180mm to 810mm wide (7”-31
high (5”-19
The manufacturer does not accept responsibility for incorrect installation.
Component Checklist
1
/
”).
2
Bits Bag
3
/
”) by 125mm to 500mm
4
™
Display Bracket (x 2)
Wall Plat e
Security Bracket
TOOLS REQUIRED:
Power Drill
12mm (1/2”), 10mm (3/8”) or 7mm (1/4”) Drill Bit
Phillips Head Screw Driver
Spirit Level
17m m (11/16”) Socket Wrench or Shifter
A
Mounting the Wall Plate
Masonry Wall
Note: E nsur e the Wal l Plat e
is moun ted wi th the f olde d
tabs pointing upwards.
12mm (1/2”)
Hole
Masonry
Wall Plug
Wall Plat e
Coach Screw
TIP: Us e a spir it leve l to
ensure the wa ll pla te is
horizontal
It is recommended when
mounting directly in to maso nry
wall, that the mounting holes
are posi tione d as far ap art as
possible.
Washer
Dry Wall Timber Stud Wall
Note: E nsur e the Wal l Plat e
is moun ted wi th the f olde d
tabs pointing upwards.
Dry Wall
Anchor
Wall Plat e
Dry Wall
Anchor Screw
TIP: Us e a spir it leve l to
ensure the wa ll pla te is
horizontal
10mm (3/8”)
Hole
Dry Wall
Anchor Washer
Coach
Screw (x4)
Multi
Washer ( x4)
Washer ( x4)
Mounting Screws
M8x15mm / M8x3 5mm / M8x45mm (x4 each)
M6x15mm / M6x35mm / M6x45mm (x4 ea ch)
M5x15mm / M5x35 mm / M5x45mm (x4 e ach)
Cross Re cesse d Screws
The dr y wall anchors p rovided in
the bit b ag have b een te sted for
this wall m ount application and w ill
each hold in exce ss of 30kg per
anchor.
Befor e using the expanding
anchor s, please ensure tha t you:
· Check th e plas ter board wall (dry
wall) is in g ood condition with no
cracks, peeling pap er or signs of
water damage etc.
· Take care ins talling the anchors,
that th ey are not over tightene d
or driven into th e wall dur ing
installation.
· Minimum thickn ess of drywall
should b e no les s than 12mm (
· Recomm end to us e all 6 anch ors
even wit h light mo nitor applica tions .
· Only use t he anch ors supplied
in the kit.
· Make sur e the 10mm (
drille d hole is as recommended and
no small er or lar ger.
· The anch ors during ex pansion
should n ot interfere with s tuds o r
noggins (cross strengtheners).
M4x15mm / M4x35mm / M4x45mm (x4 each)
1
/2”)
3
/8”) pre-
Masonry Wall
Plug (x4)
Recessed Hole
Bush (x4)
Note: E nsur e the Wal l Plat e
is moun ted wi th the f olde d
tabs pointing upwards.
7mm (1/4”)
Wall Plat e
Coach Screw
TIP: Us e a spir it leve l to
ensure the wa ll pla te is
horizontal
Use a stud finder to pre cisely
locate the timber stud and
ensure t hat the mounting hole s
are located in the centre of
the stud.
Dry Wall
Anchor (x6)
Spacer Bush (x4)
Timb er
Stud
Hole
Washer
Page 2
B
C
Multi
Washer
Mounting
screw
M6 & M8
Screw Hole
M4 & M5
Screw Hole
When attaching the Brackets ensure
that both are vertically aligned.
Ensure that the tightest fitting hole
in the multi washer is used when
attaching the mounting screw.
Recessed Mounting Holes
With the Brackets attached
to the display, lift the display
and hook the brackets onto
the Wall Plate as shown.
There are three height
positions to choose from in
50mm (2”) increments.
E
E.1.
For additional securit y, it is suggested that a Padlock is
attached through the Security Bracket and the Wall Plate
on either side as shown. The Padlock (not supplied) should
have a shackle diameter no larger than 5mm (3/16”).
No por tion of this document o r any ar twork contained herein should b e repro duced in any way without the exp ress w rit ten con sent of A tdec P ty Ltd.
Due to con tinuin g product development, the manufacture reser ves the right to alter sp ecifications without notice. Publishe d: 05.11. 08©
E.2.
(not supplied)
Loading...