Page 1
G Attaching the Mount to the Ceiling Hanger
J Adjusting the Viewing Position of your Display
Installation Instructions
TM
M8x10mm
Screw
6mm Allen
Key
Swivel Insert
M8x30mm
Screws
Step 1
Attach the three Swivel Inserts to the hanger in the height that
you have chosen for the mounting of the display.
Step 2
Attach the front and rear Hanger Pole Collar so that it sits on
the swivel collars as shown above. Tighten the M8x30mm
screws so that the hanger pole collars is secure, however do
not over tighten.
H Attaching the Mount to the Ceiling Hanger
Ceiling
Mount
Ceiling Mount
Cover
Cables
Step 1
To use the in-built cable management, remove the Ceiling
Mount Cover and feed the cables through the cable hole.
Ceiling
Mount
Ceiling Mount
Cover
Step 2
Cut out enough space in the Ceiling Mount Cover to allow
the cables to exit from, then push the Ceiling Mount Cover
up, until in sits flush with ceiling.
I Mounting the Display
Swivel Insert
Collar Front
Collar Rear
Cables
Cut Out
Note: The brackets
should rest on the
horizontal bar with the
slider between the
bracket.
1. Tilt Adjust
-5° to 25°
Tilt
M8 Small
Washer
M8x45mm
Screw
Loosen
Long 6mm
Allen Key
2. Pan Adjust
6mm Allen Key
Tighten
360° Rotation
To lock the position firmly tighten all 4 M8x30mm screws.
If free rotation of the display is required, only lightly tighten the
4 M8 x 30mm so that movement of the display is possible.
K Attaching the Adhesive Vinyl
Hanger
Adhesive
Vinyl
Step 1
Loosen the two M8x45mm screws, and adjust the
tilt angle of the display to the required position.
Tighten the two locking screws with the Long
6mm Allen Key provided.
WARNING: Do not attempt to adjust tilt
angle without firstly loosening locking
screws.
Doing so may damage the product.
Tighten
3. Horizontal Adjust
3
2
-5° to 5°
Adjust grub screw 1 until the display sits level. Once the
display is level, tighten grub screw 2 until it firmly tightens onto
the horizontal bar. Tighten grub screw 3 firmly until it firmly
tightens onto the horizontal bar and prevents it from moving.
1
Horizontal Bar
L Security Option
For added security you may
choose to attach a padlock to
one or both brackets to prevent
the theft of the display. It is
recommended that the padlock
should have a shackle diameter
of 5mm (3/16”).
TH-3070-CTW
Flat Panel Ceiling Mount
Component Checklist
IMPORTANT:
Ensure you have received all parts against the component checklist prior to installing.
Clinch Nuts
Wall Mount Bracket (Left)
Ceiling Mount
Ceiling Mount Cover
Wall Mount Horizontal Bar
Extension Hanger
Wall Mount Bracket (Right)
Slider (x2)
Inner Hanger
Bits Box
M8 x45mm
Locking Screws
(x2)
M8 x10mm
Screw (x24)
M5 x16mm
Mounting
Screws (x6)
Collar Front
M10 Coach
Screw (x4)
Long 6mm
Allen Key
Collar Rear
M10 Steel
Washer (x4)
Allen Key
Swivel Insert
Nylon Plug
5mm
(x3)
(x4)
3mm
Allen Key
Adhesive Vinyl
Strip (x6)
M8 x55mm
Screw
M8 x16mm
Mounting
Screws (x6)
M6 x12mm
Grub Screw
(x3)
M8x30mm
Screw (x4)
M6 x16mm
Mounting
Screws (x6)
A Mounting the Ceiling Mount
NOTE: Ensure all four M10 Coach Screws are used when mounting the Ceiling Mount.
Collar Joiner
Hanger Joiner
M8 Small
Washer
(x2)
Multi
Washer (x6)
M4 x16mm
Mounting
Screws (x6)
Telehook Flat Panel
Ceiling Mount
supports a maximum
weight of 91kgs
(200lbs)
NOTE:
The manufacturer
does not accept
responsibility for
incorrect installation.
The installer should
satisfy himself that the
ceiling is strong
enough to support the
Telehook Flat Panel
Ceiling Mount unit of
14kgs (31lbs) plus the
maximum allowable
monitor weight of
91kgs (200lbs).
Total of 105kgs
(231lbs).
TOOLS REQUIRED:
Power Drill
12mm (1/2”) Drill Bit
7mm (9/32”) Drill Bit
Adjustable wrench
Note: This operation will require two persons.
Lift the display with brackets attached and hook the brackets over the
sliders. Hold the display firmly and insert the two M8x45mm screws
and tighten by using the Long 6mm Allen Key.
M8 Small
Washer
Tighten
Long 6mm
Allen Key
M8x45mm
Screw
The Telehook Flat Panel Ceiling Mount’s
set up is now complete. The remaining
unused holes can be covered using the
6 white adhesive vinyl strips for improved
aesthetics. Peel the backing from the
strip and apply the adhesive side onto
the hanger(s) so that they cover the
unused holes.
Note: The Vinyl Strips may need to be cut to length
depending on the hanger configuration chosen.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 15/08/12 ©
Padlock
(not supplied)
5mm (3/16”)
diameter shackle
Masonry Mounting Option
12mm (1/2”)
Hole
M10 Washer
Nylon Plug
Masonry
Ceiling
M10 Coach
Screw
OR
Timber Beam Mounting Option
Timber
Beam
7mm (9/32”)
Hole
M10 Washer
M10 Coach
Screw
Page 2
B Attaching the Ceiling Mount Cover
Option 3: 1070mm (42
1
/8”) - 1820mm (71
5
/8”) Option 4: 1650mm (65”) - 2000mm (78
3
/8”)
D Attaching the Brackets to the Display
Step 1
Attach left and right brackets to the rear of your display. Select M4, M5, M6 or M8 fasteners to suit your display. Ensure
a minimum of 2 fasteners are used per bracket. Clinch nuts must be positioned as shown (internally).
Ceiling Mount
Cover
Slide cover plate up.
Ceiling Mount
False Ceiling
If the ceiling mount is attached where a false ceiling is used,
the ceiling mount cover should be used to hide the hole in
the false ceiling.
Ceiling Mount
Cover
C Mounting Options
There are four possible mounting options for the Telehook Flat Panel Ceiling Mount. The selected mounting option will be determined by the required distance from the ceiling to the centre of the display.
Option 1: 220mm (8
11
/16”) - 470mm (18
Ceiling Mount
Cover
Ceiling Mount
1
/2”) Option 2: 650mm (25
Ceiling Mount
M8x10mm
Screws
1
/2”) - 1000mm (39
Ceiling Mount
Cover
Inner Hanger
3
/8”)
Ceiling Mount
Cover
Ceiling Mount
M8x10mm
Screws
Inner Hanger
Extension
Hanger
Option 3:
To mount the display from1070mm (421/8”) to 1820mm (715/8”)
please use the above set up as shown. The Inner Hanger
position can be adjusted and the Collar can be mounted along
the holes on the Extension hanger. Settings are at 50mm (2”)
increments.
*See Note.
Ceiling
Mount Cover
Ceiling Mount
Inner Hanger
M8x10mm
Screws
Extension
Hanger
Hanger Joiner
Collar Joiner
Option 4:
To mount the display from 1650mm (65”) to 2000mm (783/8”)
please use the above set up as shown. Note that the Inner
Hanger position can be adjusted, and that the Collar will be
mounted to the Collar Joiner. Settings are at 50mm (2”)
increments.
*NOTE:
If you intend to mount the display along the hanger
as per Option 1 or Option 3, you may choose to cut
the excess hanger, for improved aesthetics and cable
management.
=
=
TOP
Clinch Nuts
X
Step 2:
Use the supplied Multi Washer as shown
above. Ensure that the tightest hole
in the washer is used for the size
screw. Note distance X, for use in
the following steps.
E Attaching Horizontal Rail
M6x12mm
Grub Screw
5mm
Allen Key
M8x55mm
Screw
Step 1
Insert the Horizontal Bar into the Hanger Pole Collar. Ensure
the slots on the Horizontal Bar are facing towards the Collar.
Insert the M8x55mm Screw to hold the bar in position.
Loosely insert the three M6x12mm grub screws.
3mm Allen Key
Collar Front
Horizontal
Rail
Step 2
Attach the two sliders to the Horizontal Bar, one on either
side. Tighten the grub screw into the slot, however do not
tighten
your display.
F Position Sliders
Step 1
Accurately position sliders at Distance X as recorded in Section D. Ensure the
Sliders are equally spaced along the centre Horizontal Bar.
M8 Screw Hole
M6 Screw Hole
M5 & M4
Screw Hole
Multi Washer
Horizontal Bar
Slider
Slot
Grub Screw
as the position will need to be adjusted to suit
Option 1:
To mount the display from 220mm (811/16”) to 470mm (181/2 ”)
please use the above set up as shown. Settings are at 50mm
(2”) increments.
*See note.
Collar Joiner
Option 2:
To mount the display from 650mm (251/2”) to 1000mm
3
(39
/8”) please use the above set up as shown. The Inner
Hanger position can be adjusted at 50mm (2”) increments.
Cut
Point of Contact
Slider
Grub
Screw
=
=
Tighten
Step 2
Distance X
Secure slider in position and tighten with
supplied allen key. Ensure that the grub screw
tightens into the slot on the horizontal bar.
Loading...