TH-3070-CTL
TH-3070-CTS
Component Checklist
Installation Instructions
Ceiling Tilt Short Mount / Ceiling Tilt Long Mount
HARDWARE
M6x16mm/30mm/45mm
Ceiling Cover
Mounting
Cover
Mounting
Plate
Bracket Locking
Plate (x2)
M8x15mm
Screw (x2)
Head Clamp
Assembly
Clamp Cover
Middle
Clamp Cover
Bottom
Clamp Cover
Side (x2)
M10
Washer
M10x30
Screw
M10 Coach
Bolt (x4)
Nylon
Anchor (x4)
Tightening Tool
M6/M8/M10
Washer (x4 each)
Spacer (x4 each)
Pole
Assembly
Mounting
Bracket (x2)
Horizontal Rail
M4x12mm
Screw (x2)
Cable
Clip (x2)
IMPORTANT INFORMATION:
! IMPORTANT - Install Telehook Ceiling Mount as per installation instruction.
! This product supports a maximum load of 65kg (143lbs.).
! This product has a universal mounting hole pattern that suits a broad range of TV’s:
From 200-800mm in width and 200-500mm in height.
! The manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received against the component checklist and hardware above.
Step 2. Install Mounting Plate to the ceiling
Step 3. Install Mounting Cover
M8x16mm/30mm/50mm
Display Mounting
Screws (x4 each)
M6/M8
Tools Required:
• Power Drill
• 7mm(0.25”) Drill Bit
• 12mm(0.5”) Masonry Drill Bit
• Phillips head screw driver
• 17mm(0.7”) Socket Wrench or Shifter
2mm/2.5mm/3mm
5mm/8mm Allen Key
Using the Mounting Plate as a template, mark and drill 4 holes.
Masonry Ceiling
Drilled Holes
Nylon Anchor
Mounting Plate
M10 Washer
Coach Screw
NOTE: Drilled hole sizes,
For Masonry Ceiling, Ø12mm (0.5”) and 70mm (2.75”) deep.
For Timber Ceiling, Ø7mm (0.75”).
Timber Ceiling
OR
Step 4. Attach Pole Assembly to Base Plate
4A 4B 4C
Set Screws
Remove the three set
screws using the supplied
3mm Allen Key.
INSERT
Pole Assembly
Insert the three set screws
using the supplied 3mm
Allen Key to secure.
PUSH
Pole Assembly
Mounting Cover
Step 5. Position Mounting Cover
PUSH
Mounting
Cover
Step 6. Set the Height of the Pole
6A
Whilst supporting the lower half of Pole
Assembly loosen the Socket Cap Screws
(x2) using the supplied 5mm Allen Key.
Step 7. Install the Ceiling Cover
If the lower pole hangs
below a suspended
ceiling, push the ceiling
cover up to the ceiling.
6B 6C 6D
Height Adjustment
CTL: 1050-1900mm
CTS: 550-900mm
Tighten the Socket Cap Screws
Slide Pole Assembly to the
desired height.
(x2) to set the height using the
supplied 5mm Allen Key.
Step 8. Install the Clamp Head
8A 8B 8C
Set Screws
If necessary, centralise the Pole Joint
by tightening the Set Screws (x2) to suit
using the 2.5mm Allen Key.
Push up to the ceiling
Step 9. Install the Horizontal Rail
9A. To Set Orientation
Loosen the three set screws
using the supplied 3mm Allen
Key.
NOTE: The rail mount is factory set in
the horizontal axis.
ATTACH
Secure the collar with the
three set screws using the
supplied 3mm Allen Key.
9B. Insert
Horizontal
Rail
INSERT
1. Loosen the 4 screws using the supplied
2.5mm Allen Key.
9C. Secure Horizontal Rail
1. Make sure the large slot of Horizontal Rail is facing front.
2. Align the holes of the Horizontal Rail and Head Clamp.
3. Lock in place with M10 Screw and Washer using the
supplied M8 Allen Key.
2. Rotate the head clamp 90° and insert
the 4 screws again using the supplied
2.5mm Allen Key.
Large Slot
Horizontal Rail
Loading...