TH-3065-LPT
5mm
(
3
/
16
”)
50mm (2”)
Stud
10mm
(
3
/8”)
58mm
(2.3”)
Wall
Component Checklist
Installation Instructions
Flat Screen Wall Mount | Tilt
Wall Plate
End Cap (x2)
Tilt Bracket (x2)
Wall Plate
Wall Mounting HardwareTools Required Display Mounting Hardware
• Power Drill
• Phillips Head
Screwdriver
A1
M4x12/25
(x4 each)
A2
M5x12/25
(x4 each)
A3
M6x12/25
(x4 each)
A4
M8x16/25
(x4 each)
A5
M8
Spacer
(x4 each)
A6
Multi
Washer
(x4 each)
B1
Coach
Screw
(x4 each)
B2
Nylon
Anchor
(x4 each)
• 5mm (1/4”) Drill Bit
• 10mm (3/8”)
Masonry Drill Bit
• 13mm (1/2”) Socket
Wrench or Shifter
IMPORTANT INFORMATION
! IMPORTANT Install Telehook TH-3065-LPT Wall Mount as per the Installation Instructions
! This product supports a maximum load of 40Kg (88 lbs).
! This product only supports displays with mounting hole confi gurations from 100mm x 100mm (min.) to 600mm x 400mm (max.).
! The manufacturer does not accept responsibility for incorrect installation.
! Before installing this Telehook product, please check the display ventilation requirements with your LED/LCD manufacturer.
Step 1. Check Components
B2
Washer
(x4 each)
Check you have received all parts by comparing supplied parts against the Component Checklist and Hardware lists above.
Step 2. Mount the Wall Plate
Masonry Wall Timber Stud
3
10mm (
/
”) hole
8
OR
B2
B3
B1
Tip: Use the supplied magnetic bubble level
to ensure wall plate is horizontal.
Note: Use a stud fi nder to accurately locate the centre of each
stud. Ensure that all four screws are fi xed securely into the studs.
5mm (
3
/
”) hole
16
B3
B1
Click!
Push
Rear View of Screen
A
TOP
Pull
12max
Step 3. Attach Tilt Brackets to Screen
A1|A2|A3|A4
Mounting Screw
A6 Multi-washer
For M8 Screws
For M5 &
M6 Screws
For M4 Screws
Tilt Bracket
A5 Spacer (optional)
Use for recessed
mounting holes only.
Use longer mounting
screws with spacers.
Step 4. Attach End Caps
Push each of the End Caps
onto the tabs at each end
of the wall plate.
Step 6. Unlocking Screen
Step 5. Attach Screen to Wall Plate
5.1 Hook the Tilt
Brackets onto the
top edge of the
Wall Plate.
Step 7. Cable Management
Note: If dimension ‘A’ is larger than
195mm (7.68“) the maximum tilt
shown in Step 8 will be reduced.
x2
(two people required)
5.2 Lock the
screen to the
Wall Plate by
gently pushing
the bottom of
the screen.
Step 8. Set Screen Tilt
Pull down both strings to unlock the Tilt
Brackets from the Wall Plate.
TIP: Hide strings by
sticking magnetic
pendants onto the
Tilt Brackets behind
the screen.
Installation Complete
Unlock the Tilt
Brackets from
the wall plate.
Pull the bottom
of the screen out
from the wall to
provide access for
connecting cables
to the screen.
Once cables are
connected, lock
screen to Wall Plate
as in Step 5.2.
Once the brackets
are locked, set the
screen tilt by gently
pulling or pushing
the top edge of the
screen.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 18.08.15 ©
Loading...