Atdec TH-3060-UFH, TH-3060-UFL User Manual

M6x16mm

Large-Medium TV Articulated Arm

M6x16mm

M6x25mm

5mm/4mm

Allen Key

M6x16mm

M6x25mm

M8x16mm

Large-Medium TV Articulated Arm

Allen Key

M6x16mm

M6x25mm

M8x16mm

Allen Key

M6x16mm

M6x25mm

M8x16mm

TH-3060-UFH

Component Checklist

Installation Instructions

Flat screen wall mount | Full Motion height adjustable

Arm

Wall plate
cover (x2)

Display

Mount

Display

Bracket (x2)

Hardware Bag

Coach Screw (x4)

Nylon Anchor (x4)

M6 Nyloc Nut (x4)
M6 x 6mm screw (x4)

Mount

cap (x2)

Spanner

6mm/4mm
Allen key

12mm Washer (x4)
20mm Washer (x4)

Tools required:

- Philips head screwdriver

- Power drill

- 5mm (0.2”) drill bit

- 10mm (0.39”) masonary drill bit

IMPORTANT INFORMATION

! IMPORTANT - Install Telehook Flatscreen wall mount as per Installation Instructions

! This product supports a minimum load of 5kg (11lbs) and a maximum load of 25kg (55lbs)
! This product supports VESA mounting hole configurations from 200mm x 200mm to 400mm x 400mm
! The Manufacturer accepts no responsibility for incorrect installation.

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware.

Step 2. Mounting Location

This product has a feature where the arm will automatically lock in position when
pushed up against the wall to the left. If this feature is to be used allow clearance
to the left when deciding the mounting location.

Display Mounting
Screws Bag

M8 x 16mm (x4)
M8 x 25mm (x4)

M6 x 16mm (x4)
M6 x 25mm (x4)

Wall

locked position

Clearance

free movement

To unlock, pull the chord down whilst
moving the arm away from the wall

Step 3. Install Arm to the wall

Masonary Wall Timber Stud wall

Drilled hole

Wall

Coach Screw

Nylon Anchor

Coach Screw

Drilled hole

Washer

- Using a 10mm (0.39”) masonary drill bit, Drill four holes,
60mm (2.4”) deep.

- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.

Washer

- Using a 5mm (0.2”) drill bit, Drill three holes , 60mm (2.4”)
deep.

- Secure the mounting plate to the wall using the Coach
Screws supplied.

NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.

Step4.AttachWallPlateCovers

Step5.AttachDisplayMounttoArm

Threaded stud

PUSH

Step6.HorizontalRotationAdjustment

B.This will

5° 5°

allow 10°
Horizontal
rotation
adjustment

x2

Note:The nuts can be re-tightened to

secure the display in position or left to allow
future changes

A.From the
tightened position
undo each nut a
quarter of a turn two
times

Washer

Mount

Step7.AttachScrewCovers

M6 Nyloc Nut
(tighten firmly)

PUSH

Step8.AttachMountingRailsToDisplay

The Mounting rails support VESA hole
configurations from 200mm x 200mm to
400mm x 400mm

Only insert the M6 x 6mm screws in
the mounting rail attached to the top of
the display. Tighten fully then undo one
half turn

Display mounting screw

Mounting rail