Page 1
TH-3060-LPF
Components Checklist
Installation Instructions
Flat Screen Wall Mount | Fixed
Hardware
M5x30/16mm (x4 each)
Coach Screw (x2)
Dry Wall anchor (x4)
M6x30/16mm (x4 each)
Wall Plate
Tools Required:
Power Drill
6mm
Phillips Head screwdriver
10mm
Large Flat Head Screw Driver
13mm
1
drill bit
(
")
4
3
masonry drill bit
(
")
8
1
Socket Wrench or Shifter
(
")
2
Display Bracket (x2)
10mm ( drill bit
Spirit Level
3
")
8
M5/6/8 Washer
(x4 each)
M6/8 Spacer (x4)
M4/5 Spacer (x4)
M8x30/16mm (x4 each)
Display Mounting
Screws
Nylon Anchor (x2)
IMPORTANT INFORMATION
! IMPORTANT - Install Telehook 3060 Wall Mount as per Installation Instructions.
! This product supports a maximum load of 65kg (143.3lbs).
! This product supports displays with mounting hole configurations from 100mm (4”) to 500mm (19½”) high,
and from 200mm (8”) to 810mm (32”) wide.
! The manufacturer does not accept responsibility for incorrect installation.
! Before installing this Telehook product, please check the display ventilation requirements with your
LED/LCD manufacturer.
Step 1. Check Components
Check you have received all parts against the component checklist and Hardware above.
Step 2. Mounting the Wall Plate
Dry Wall
Each Dry Wall anchor should be at a
Note:
maximum distance from the next anchor point.
This is the recommended mounting pattern for
Dry Wall Anchors.
Dry Wall Anchor
3
10mm(
") Hole
8
Wall Plate
Dry Wall Anchor Screw
Tip: Use a spirit level to ensure wall plate is horizontal.
OR
Masonry Wall
Nylon Anchor
Wall Plate
Coach Screw
10mm(
3
") Hole
8
Timber Stud
Use a stud finder to accurately locate
Note:
the centre of the stud. Ensure that all two
screws fix securely into the stud.
OR
1
6mm(
") Hole
4
Wall Plate
Coach Screw
Timber Stud
Page 2
Step 3. Attaching Brackets to Display
Tip: If Hook Plates obstruct mounting
holes, remove and reposition
(as shown below.)
Bracket
Washer
Spacer
(optional, used only for
recessed mounting holes)
Mounting Screw
Back of Display
TOP
Note: Ensure that both
Release Ties are closest
to the outside edge of
the Display.
Release Tie
Use a large flat blade screwdriver
to remove/replace the two Hook
Plate screws.
Step 4. Attaching/Detaching Display to Wall Plate (2 people required)
With the Brackets attached to the Display,
lower the Hook Plates onto the Wall plate.
Listen for "CLICK" to ensure the catch has
engaged.
Hook Plate
Hook Plate Screw
Slide Display to desired position.
Detaching Display from Wall Plate:
To detach Display from wall plate, pull and
hold Release Ties to disengage locking
mechanism. Then lift the Display to unhook
from the wall plate.
Step 5. Cable Management
To access cable ports,
Note:
fold out screen tilt supports.
Power Cable
Release Tie
Fold Tilt Supports back
once all
cables have been installed.
Hook Plate
Wall Plate
screen tilt support
Cut Release Ties so that they cannot
be seen from front of screen.
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 14.10.10 ©
Loading...