Page 1
TH-1040-VFM
Component Checklist
Installation Instructions
Flat Screen Wall Mount / Full Motion
Hardware
M4/M5 Washers
(x4 each)
M6/8 Spacer (x4)
3mm Allen Key
Articulated Arm
VESA Plate
Tools Required:
Power Drill
•
6mm (0.25”) Drill Bit
•
10mm (0.4”) Masonry Drill Bit
•
Phillips-head Screwdriver •
13mm (0.5”) Socket Wrench or Shifter
•
Drill Guide
Coach Bolt (x2)
Concrete Anchor (x2)
M4/5 Spacer (x4)
Security Screw (x1)
IMPORTANT INFORMATION:
! IMPORTANT - Install Telehook 1040 Flat Screen Wall Mount as per Installation Instructions.
! This product supports a maximum load of 25kg (55lbs).
! This product supports VESA mounting hole configurations: VESA plate, 75x75mm, 100x100mm, 200x100mm,
and 200x200mm.
! The manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the component checklist and Hardware above.
Step 2. Locate Drilling Position
Choose the location of your
Telehook Wall Mount,
ensuring that the wall is
structurally sound (for a
timber stud wall, locate the
stud using a stud detection
device). Use the Drilling
Guide to mark out the hole
centres.
Drilling Guide
FRONT
Dust Collector
Un-fold the Drilling Guide and
open the Dust Collector.
Top
Drilling Guide
BACK
Double-sided
tape (x2)
Peel away the backing from the
double-sided adhesive tape.
Position the Drilling Guide vertically
onto the wall using a Spirit Level.
Display Mounting
Screws
M4x16/25mm (x4 each)
M5x16/25mm (x4 each)
M6x16/30mm (x4 each)
WALL
Step 3. Attaching the Articulated Arm to the Wall
Remove the Telehook Arm from the packaging and open fully.
Timber Stud Wall
- Drill two 6mm (0.25”) diameter holes, 50mm (2”) deep.
- Secure the Mounting Plate to the wall using the Coach
Bolts supplied.
Coach Bolt (x2)
Slide the Wall Plate Cover back along
the arm, and push flat against the wall.
OR
Un-clip the Wall Plate Cover and slide down the arm.
Wall Plate Cover
Masonry Wall
- Drill two 10mm (0.4”) diameter holes, 50mm (2”) deep.
- Secure the Mounting Plate to the wall using the Coach
Bolts and Concrete Anchors supplied.
Coach Bolt (x2)
Concrete Anchor (x2)
Page 2
Step 4. Attaching the VESA Plate to your Display
Choose appropriate Mounting Screws and
Washers from the Hardware supplied
Mounting Screws (x4)
Washers (x4)
VESA Plate
Top of
Display
to suit your Display.
Back of Display
Step 5. Attaching your Display to the Arm
Hook the top of the VESA Plate onto the VESA
Ball Mount.
VESA Plate
VESA Ball Mount
HOOK
Press and hold the Release Buttons. Gently push
bottom of VESA Plate into VESA Ball Mount.
Release Buttons to lock in place.
Release Button
Recessed Mounting
Holes or Display with a
Curved Rear Panel
If the Mounting Holes are
recessed into the back of the
Display, or the Display has a
curved rear panel, use the
appropriated Spacer Bushes
supplied to pack the
Mounting Holes.
Note: Ensure the VESA
plate is securely fixed
to the display.
PUSH
Mounting Screw
Washer
Spacer
Mounting Hole
Insert the Security Screw, and tighten using the
Phillips-head Screwdriver.
TIGHTEN
Security Screw
Phillips-head Screwdriver
Step 6. Cable Management
Remove the Cable Covers as required using a Phillips-head
Screwdriver.
Cable Cover
Step 7. Final Adjustment
Position your Display to the desired viewing angle using the 40°
angular movement allowed by the VESA Ball Mount.
If the display does not hold its position, or is too
LOOSEN (-kg)
Tension Plate
3mm Allen Key
TIGHTEN (+kg)
resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount.
To make any adjustments, use the 3mm Allen Key
supplied. Apply half a turn at a time to each screw
on the Tension Plate to adjust evenly.
Check the display, and then adjust again if necessary.
Connect cables to your Display, and route along the arms.
Re-attach the Cable Covers to hold the Cables in place.
TI P : Leave enough slack in the cables
to allow full movement at the joints.
+/- 20°
angular tilt
360° infinite
horizontal rotation
Rotate the Display as desired, locking the
Display into position by tightening the
Tension Plate.
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 30 .10.11 ©
Loading...