Page 1
Component Checklist
Bits Bag
Installation Instructions
TELEHOOK
32”-63” WALL TILT
Mounting the Wall Plate
A
Timber Stud Wall
Masonry Wall
Display Bracket (left)
Wall Plate
Coach Screw (x4)
Masonry Wall Plug (x4)
Washer (x4)
Recessed Hole Bush (x4)
Washer
Masonry
Wall Plug
Wall Plate
12mm (1/2”)
Hole
Note: Ensure the Wall Plate
is mounted w ith the folded
tabs pointing upwards.
Coach Screw
8mm (5/16”)
Hole
Important Notes
TOOLS REQUIRED:
l
Power Drill
l
12mm (1/2) or 8mm (5/16) Drill Bit
l
Phillips Head Screw Driver
l
Spirit Level
l
17mm (11/16”) Socket Wrench or
Shifter
l
The Telehook 32-63 Wall Tilt supports LCD and Plasma Flat Panel Displays from 32” (81cm)
to 63” (160cm) and supports a maximum load of 91kgs (200lbs).
l
This product suits displays with mounting hole patterns from 180mm to 740mm wide (7”-29”) by 100mm to
500mm high (4”-20”).
l
The manufacturer does not accept responsibility for incorrect installation.
Security Bracket (right)
Security Bracket (left)
Multi Washer (x4)
Spacer Bush (x4)
Mounting Screws
M8x15mm / M8x35mm / M8x45mm (x4 each)
M6x15mm / M6x35mm / M6x45mm (x4 each)
M5x15mm / M5x35mm / M5x45mm (x4 each)
M4x15mm / M4x35mm / M4x45mm (x4 each)
Cross Recess ed Screws
TIP: Use a spirit
level to ensure
that the wall plate
is horizontal
Note: Ensure the Wall Plate
is mounted w ith the folded
tabs pointing upwards.
Wall Plate
Coach Screw
Washer
Timber
Stud
Display Bracket (right)
TIP: Use a spirit
level to ensure
that the wall plate
is horizontal
Page 2
Attaching the display to the wall
plate
B
Multi
Washer
M6 & M8
Screw Hole
M4 & M5
Screw Hole
Mounting
screw
Markings
E
C
When attaching the Brackets
to the display, use the markings on
the brackets to ensure that both
brackets are vertically aligned.
Ensure that the markings are
positioned towards the top of the
display and that the tightest fitting
hole in the multi washer is used
when attaching the mounting
screw to the display.
Recessed Mounting Holes
If the mounting holes are
recessed into the back of
the display, use the supplied
Recessed Hole Bushes to pack
the recessed hole. If the brackets
require further clearance from
the display, attach the Spacer
Bushes. Ensure the brackets are
securely fixed to the display.
With the brackets attached to the display, lift the
display and hook the brackets onto the Wall Plate
as shown.
Note: For demonstration purposes, the wall
has been omitted from the above images.
Note: For demonstration purposes, the display
has been omitted from the images below.
Adjusting Tilt
D
For additional security, it is suggested that the left and right Security
Brackets be inserted and a Padlock attached through each Security
Bracket and the Wall Plate as shown. The two Padlocks (not supplied)
should have a shackle diameter no larger than 5mm (3/16”)
-5° to 15°
tilt adjustment
TIGHTEN
LOOSEN
Note: For demonstration purposes, the display
has been omitted from the above images.
To adjust the angle of the display, loosen the Tilt Lever
located on each bracket then adjust to desired angle. Once
in position, tighten each lever firmly.
Tilt Lever
To adjust the Tilt Lever position
without tightening or loosening
the lever, pull the lever as shown
to dis-engage the ratchet
mechanism and rotate the lever
into the desired position.
Tilt Lever
PULL
ADJUST
Ensure both Tilt
Levers are facing
outwards.
Due to continuing product development, the manufacture reserves the right to alter specifications without notice. Published: 08.10.07©
Note: This procedure will require two persons
D.1.
D.2.
E.2.
E.1.
Back of
display
Loading...