Atdec Spacedec SD-POS-VBM-B2B, Spacedec SD-POS-HA-B2B, Spacedec SD-POS-VBM, Spacedec SD-POS-HA Installation Instructions Manual
Page 1
A. Determine the degree of
rotation you require. (Refer to
Mounting Options above)
B. To Limit the Rotation,
use the 2.5mm Allen Key to
insert the supplied M5
Grub Screw into your
chosen Locking Hole until it
sits flush with the Base Plate.
N
OTE: If you want the full
355° rotation, you do NOT
need to install a grub screw.
Step 1. Limit Rotation
Component Checklist (Check you have received all parts against the Component Checklist below)
M4x10mm Screws (x4)
M4x16mm Screws (x4)
POS Assembly (x1)
Hardware
2.5mm Allen Key (x1)
M4x12mm Screws (x4)
Installation Instructions
Installation Template
(x1)
M5 Grub Screw (x1)
4 x Ø3mm (1/8”)
Pilot Holes
Centre for
45mm(1¾”) Cable
Access Hole
Mounting Options
A. Position the Installation
Template in the desired location
on your work surface. Ensure the
straight edge sits perpendicular
with the User’s line of sight. Mark
the center points of each of the
required holes onto the work
surface with a pencil.
B. Drill 4 x 3mm (
1
/8”) Pilot
Holes to a depth of 15mm (
9
/16”).
Use a 45mm (1¾”) hole saw to
drill the Cable Access Hole in the
work surface.
C. Reposition POS Multi with
the “Direction Arrow” pointing in
the direction required for your
chosen rotation. Secure the POS
to the work surface using the
supplied 14 Gauge Screws (x4).
INSTALLATION
TEMPLATE
Top Cap (x1)
Screw Cover
(x1)
14 Gauge Screws (x4)
0° Locking Hole (Fixed)
0-180° Locking Hole
0-270° Locking Hole
0-90° Locking Hole
Direction Arrow
Locking Holes
Rotation Options
0° Rotation (Fixed)
0-90° Rotation
0-180° Rotation
0-270° Rotation
0-355° Rotation
OR
4x
M5x75mm Screws
(To suit 70mm
4x M5
Cable Management
Hole
14 Gauge
Screws (x4)
Ø45mm
(1¾”) Cable
Access Hole
4 x Ø3mm (
1
/8”)
Pilot Holes
USER
USER
5° Gap in
Rotation
USER
Step 2. Locate and Secure your POS Multi
5° Gap in
Rotation
270°
180°
0°
90°
270°
180°
0°
90°
355°
355°
M5 Grub Screw
Your POS Multi offers 355° of
Rotation. This can also be limited
to suit a specific application.
The Direction in which you
mount POS Multi will determine
where the 5° gap in Rotation is
located, and how you choose to
limit the rotation.
2.5mm Allen Key
Base Plate
Direction
Arrow
Direction
Arrow
2mm Allen Key (x1)
Display | POS Multi
SD-POS-VBM
Security Screw (x1)
Tightening Tool (x1)
VESA plate (x1)
Page 2
A. Loop the Security Cable
(Kensington or similar)
around the internal post
of the POS Assembly.
B. Feed the other
end
of the cable through
the POS Assembly and
out the Cable
Management Hole.
C. After you have attached the monitor
(As directed in Step 8) install the lock to the
monitor as per the manufacturer guidelines.
Step 5. Install Top Cap
Step 4. (Optional) Install Monitor Security Cable (Security Cable NOT Included)
Prior to attaching your monitor,
install the monitor cables.
Run them through the Cable
Management Hole, down the
pole and out the Cable Access
Hole in the work surface.
Step 6. Install Monitor Cables
Top Cap
Cable
Management
Hole
OUT
IN
Step 3. Attach Screw Cover
Remove the paper backing from the Screw
Cover and adhere to the POS base as shown.
Screw
Cover
These Installation Instructions secure
the POS Multi using the provided
fasteners from above thework surface.
For advanced Security Installation from
below the work surface. Please refer to
the Advanced Security Installation
Addendum.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 27.07.09 ©
Position your Display to the desired viewing
angle, using the 40° angular movement
allowed by the VESA Ball Mount.
If the display does not hold its position,
or is too resistant, adjust the Tension Plate
(see diagram right).
To make any adjustments, use the
Tightening Tool supplied.
Top of
Display
There are two mounting hole configurations:
UКЗxКЭКЗx
UК£ддКЭК£дд
Choose appropriate Mounting Screws
from the Hardware supplied to suit
your Display.
Mounting Screws (x4)
VESA Plate
Back of Display
Çx
(3”)
£ää
(4”)
Çx
(3”)
£ää
(4”)
Step 7. Attach the VESA plate to your Display
Step 8. Attach your Display to the POS Assembly
Step 9. Adjust the VESA Ball Mount
Advanced Security Installation
PUSH
Push down firmly to attach the Top Cap.
Hook the top of the VESA plate onto
the Quickshift Mount.
Gently push the bottom of the Display
into the Mount until you hear a ‘CLICK’.
Insert the Security Screw, and tighten
using the 2mm Allen Key supplied.
Tighten (+Kg)
Loosen (-Kg)
Tension
Plate
Tightening
Tool
Security
Screw
CLICK
PUSH
HOOK
TIGHTEN
Back of Display
2mm
Allen Key
Page 3
Advanced Security Installation Addendum
Step 1. Purchase M4 Fasteners
Using the M4 Security Holes, your POS
Multi can be secured from beneath the
work surface for greater security.
Determine the length of Screw
you require using the formula shown,
and purchase 4x M4 Screws and
Washers, with your chosen drive type.
Screw Length Formula Security Holes
A. Position the Installation Template in the desired location on your work surface. Ensure the straight edge sits
perpendicular with the User’s line of sight. Mark the cente
r points of each of the Security Holes, and Cable Access
Hole onto the work surface with a pencil.
B. Drill 4 x 5mm (0.18”) holes through the work surface (Take care to drill perpendicular to the
work surface). Use a 45mm (1.77”) hole saw to drill the Cable Access Hole in the work surface.
C. Reposition POS Multi with the “Direction Arrow” pointing in the direction required for your chosen rotation.
(Refer to the Mounting Options in POS Multi Installation Instructions) S
ecure the POS to the Desktop using the
purchased M4 fasteners (x4).
Step 2. Locate and Secure your POS Multi
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 23.07.09 ©
NOTE: Return to POS Multi or Back-to-Back Installation Instructions to finish Installation
Work Surface
+
Washer
Thickness
+
5mm (0.18”)
Length =
M4
Thread
M4
Security
Holes
4 x Security Hole
Centre Point
Centre for
45mm (1.77”) Cable
Access Hole
Ø45mm(1.77”)
Cable Access
Hole
M4 Screws
NOT
Provided
M4 Washers
Ø5mm (0.18”)
Mounting
Holes (x4)
Drive Type
INSTALLATION
TEMPLATE
USER
Display | POS Multi
SD-POS-VBM
SD-POS-VBM-B2B
SD-POS-HA
SD-POS-HA-B2B
Loading...