Page 1
B.1. Adjusting B all Jo int fri ctio n
Depending on t he weight of the display, it may b e
neces sary to make adjustmen ts to the B all Joint
Mechanism. If t he displ ay does n’t hold it s positi on
or is too resistant, adjust the four tension screws
located around the Ball J oint (se e diagram) using
the supp lied 2.5 mm Allen Key.
Check th e display, and then a djust ag ain if
necessary.
NOTE: Be sure to adjust screws evenly.
B.2 . Adju sting Pivot He ad ten sion
It is possible to control the amount of resistance
in the Pivot Head to suit your display.
To increas e the res istance of the Pi vot Head to
suit heavier displays, use the 5mm Allen Key
supplied in the Desk Clamp Box to tig hten the
interscrew in a clockwise direction.
To decrea se the re sistan ce of the Pivot Hea d to
suit lighter displays, loosen the interscrew in an
anti-clockwise direction.
NOTE: It is recomme nded t he Pivot
Head b e left a t the factor y setting fo r
best performance.
B.3. Adjus ting G as Str ut Res istance
B. 3.1 Depending on the weight of the display,
it may be n ecess ary to a djust th e arm. This can
be done by using the supplied 5mm Allen Key.
B.3.2. If the arm tends to automat ically r ise
or fall when the display is attached, it will be
necessar y to make small adjustments to the gas
stru t. (see dia gram)
B.3.3. If the arm tends to rise, the gas strut
position should be raised. If the arm tends to
fall, the g as strut posit ion shou ld be lowe red.
2.5mm
Allen Key
Arm
Interscrew
5mm Allen Ke y
Loosen
Lighter
display
Heavier
display
Loosen
Tighten
5mm
Allen key
Tighten
Lighter
Heavier
Lower Gas Strut to
suit heavi er display
Tension
Screws (x 4)
Ball Joint
Pivot Hea d
Gas Stru t
Raise Gas Strut
to suit lighter
display
remove card from the
Please do not
Spacedec Acrobat
Articulated Wall Arm
SPACEDEC ACROBAT
ARTICULATED WALL ARM
USER
OPERATING CARD
For your comfort and safety please take a few
moments to adjust the position of your display
To adjust the Spacedec Acrobat Articulated
Wall Arm, please refer to the instructions in
this User Operating Card
Use the Ergonomic Guidelines overleaf
as a guide for correct positioning
Page 2
Ergonomic Guidelines
Ergonomists r ecommend that the optimal posi tion of your screen should b e slightly below eye level.
When lo oking at the scre en’s centre the user s hould ha ve a downward visual angle of approx. 10 °-20°.
As a guid e, the hei ght (h) of your display should be approximate ly as follo ws:
1
5°
10°-20°
/
2”)
1
/
2”) is recommended.
15°
(h)
Tall Male (Ma x): 560mm (22” ) Tall Female (M ax): 520mm (20
Short M ale (Min): 368mm (14
1
/
2”) Short Fe male (Min): 356mm (14”)
For visua l comfor t, a viewin g distan ce (d) between 500m m (20”) to 750mm (29
Angular adjustments to reduce reflection on your display should range between 5° forward tilt to 15°
back ward tilt.
HORIZO NTAL SIGHT LI NE (d)
CENTR E OF SCREEN
A
Adjusting D ispl ay
Your Ar ticulated Wa ll Arm s hould alrea dy be pr eset to a ccommodate the average
size/weight of a display. To adjust the position of your display for visual comfor t,
simply hold b oth sides of the disp lay an d adjust to des ired positi on.
SPACEDEC ACROBAT
ARTICULATED WALL ARM
B
Mechanical Adjustment
If undesired tilt or pan occurs at any stage, this means the factory settings on your Articulated Wall
Arm re quires a djustm ent. Ple ase refe r to adjus tment details overlea f.
B.1. Ball Joint friction
B.2 . Pivot Head tens ion
B.3. Gas Str ut resi stanc e
B.1.
B.2.
atdec.com
B.3.
Published: 24.10.07©
Due to conti nuing product de velopment, the man ufacturer
reser ves the right to alte r specificati ons without noti ce.
Loading...