Atdec SD-WD User Manual
SD-WD
Installation Instructions
Display | Wall Direct
Note: This product will suit VESA complia nt mon it ors with 75mm x 75mm (3” x 3”) and 100mm x 100mm (4” x 4 ”) hole patterns only.
It will support up to a maximum weight o f 25kg (55lbs) .
Component Checklist
VESA
plate (x1)
Wall Mount
Assembl y (x1)
TOOLS REQUIRED:
• Power Drill
• Phillips-head Screwdriver
• 4mm (
• 8mm (
• 8mm (
or Shifter
3
/16”) Drill Bit
5
/16”) Masonry Drill Bit
5
/16”) Socket Wrench
Hardware
(Optional)
Security
Screw (x1)
Nylon
Anchor (x4 )
Mounting Fasteners
M4x10mm
Screw ( x 4)
M6 Coach
Screws ( x 4)
M4x12mm
Screw ( x 4)
Combined 3mm
Allen Key and
Phillips-head
Screwdriver (x1)
M4x16mm
Screw ( x 4)
Step 1. Component Checklist
Check you have receiv ed a l l parts against the Component Checkl ist abo v e .
Step 2. Installing the Wall Mount Assembly (choose from one of the following options)
For mounting Spacedec to a Timber Stud Wall - Using the Wal l Moun t Assembly Bracket, mark
the location of the 4 holes and dril l u si ng a 4 m m dril l bit. Secure the bracket t o the w al l u si ng the M 6 Coach
Screws as shown in diag ram A.
For mounting Spacedec to a Masonry Wall - Using the Wall Mount Assembly Bracke t, mark
the location of the 4 holes and dril l u si ng a n 8mm mason ry drill bit. Secu re the brac k et t o the wa l l u si ng the M6
Coach Screws and Nylon Anchors as shown in diagram B.
Stud
4 x 4mm
Holes
Wall Material
Wall Mount Assembly
Bracket
M6 Coach
Screw
4 x 8mm
Holes
Mason ry Wal l
Nylon Anchor
Wall Mount Assembly
Bracket
M6 Coach Screw
A. Timber Stud Wall
B. Masonry Wall
Step 3. Attach the VESA plate to your Display
There are two mounting hole configurations:
• 75 x 75mm
• 100 x 100mm
Choose appropriate Mounting Screws
from the Hardware supplied to suit
your Display.
Top of
Display
100mm
(4”)
Step 4. Attach your Display to the Wall Mount Assembly
75mm
(3”)
Mounting Screws (x4)
VESA Plate
75mm
100mm
(3”)
(4”)
Back of Display
Hook the top of the VESA Plate onto
the VESA Ball Mount.
Press and hold the Release Buttons.
Gently insert bottom of VESA Plate
into Quickshift Mount. Release
Buttons to lock
in place.
Back of Display
Step 5.
Adjust the VESA Ball Mount
Position your Display to the desired viewing angle, using the 20°
angular movement allowed by the VESA Ball Mount.
Depending on the weight of the displa y, it may be necessary to make
adjustments to the VESA Ball Mount. If the display does not h o l d i t s
position, or is too resistant, adjust the Tensi on Plate located at the
rear of the VESA Ball Mount (see diagram right ).
To ma k e any adjustments tension evenly using the 3mm Allen Key
supplied. Apply half a turn at a time to each screw on the Tension
Plate to adjust evenly.
Check the display, and then adju st agai n if necessary.
(Optional) Insert the Security Screw
supplied and tighten using a
Phillips-head Screwdriver.
Security
Screw
Combined Phillips-head
Screwdriver/Allen Key
supplied
Tension
Plate
Combined Phillips-head
Screwdriver/Allen Key
supplied
Loosen (-Kg)
Tighten
(+Kg)
Installation Complete
No portion of this document or a ny artwork contained herein should be reproduced in a ny way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 23.11.11 ©
Loading...