Atdec SDPOSVBMB2B User Manual

SD-POS-VBM

Installation Instructions

Display | POS Multi

Component Checklist (Check you have received all parts against the Component Checklist below)

Hardware

Screw Cover

(x1)

POS Assembly (x1)

VESA plate (x1)

Top Cap (x1)

Mounting Options

Your POS Multi offers 355° of
Rotation. This can also be limited
to suit a specific application.
The Direction in which you
mount POS Multi will determine
where the 5° gap in Rotation is
located, and how you choose to
limit the rotation.

Rotation Options

0° Rotation (Fixed)

0-90° Rotation
0-180° Rotation
0-270° Rotation
0-355° Rotation

Step 1. Limit Rotation

A. Determine the degree of

rotation you require. (Refer to
Mounting Options above)
B. To Limit the Rotation,
use the 2.5mm Allen Key to
insert the supplied M5
Grub Screw into your
chosen Locking Hole until it
sits flush with the Base Plate.

OTE: If you want the full

N
355° rotation, you do NOT
need to install a grub screw.

Direction

Arrow

Installation Template

(x1)

Tightening Tool (x1)

180°

270°

2.5mm Allen Key

M5 Grub Screw

Base Plate

5° Gap in

Rotation

0°

355°

Locking Holes

90°

M4x10mm Screws (x4)

M4x12mm Screws (x4)

M4x16mm Screws (x4)

Security Screw (x1)

OR

USER

5° Gap in

Rotation

0°

90°

355°

Direction

Arrow

Direction Arrow

2.5mm Allen Key (x1)

2mm Allen Key (x1)

14 Gauge Screws (x4)

M5 Grub Screw (x1)

270°

180°

USER

0° Locking Hole (Fixed)

0-90° Locking Hole

0-180° Locking Hole

0-270° Locking Hole

Step 2. Locate and Secure your POS Multi

A. Position the Installation

Template in the desired location
on your work surface. Ensure the
straight edge sits perpendicular
with the User’s line of sight. Mark
the center points of each of the
required holes onto the work
surface with a pencil.

1

B. Drill 4 x 3mm (
Holes to a depth of 15mm (

/8”) Pilot

9

/16”).
Use a 45mm (1¾”) hole saw to
drill the Cable Access Hole in the
work surface.
C. Reposition POS Multi with
the “Direction Arrow” pointing in
the direction required for your
chosen rotation. Secure the POS
to the work surface using the
supplied 14 Gauge Screws (x4).

4 x Ø3mm (

Pilot Holes

4x

M5x75mm Screws

(To suit 70mm

1

/8”)

Cable Management

Hole

14 Gauge

Screws (x4)

4x M5

Ø45mm

(1¾”) Cable

Access Hole

4 x Ø3mm (1/8”)

Pilot Holes

Centre for

45mm(1¾”) Cable

Access Hole

INSTALLATION

TEMPLATE

USER

Step 3. Attach Screw Cover

Remove the paper backing from the Screw
Cover and adhere to the POS base as shown.

Screw
Cover

Step 4. (Optional) Install Monitor Security Cable (Security Cable NOT Included)

A. Loop the Security Cable

(Kensington or similar)
around the internal post
of the POS Assembly.

B. Feed the other

end
of the cable through
the POS Assembly and
out the Cable
Management Hole.

C. After you have attached the monitor
(As directed in Step 8) install the lock to the
monitor as per the manufacturer guidelines.

Step 5. Install Top Cap

Top Cap

PUSH

Step 6. Install Monitor Cables

Prior to attaching your monitor,
install the monitor cables.

Run them through the Cable
Management Hole, down the
pole and out the Cable Access
Hole in the work surface.

Push down firmly to attach the Top Cap.

Step 7. Attach the VESA plate to your Display

There are two mounting hole configurations:

UКЗxКЭКЗx
UК£ддКЭК£дд

Choose appropriate Mounting Screws
from the Hardware supplied to suit

Top of

Display

your Display.

£ää

(4”)

Çx

(3”)

Cable

Management

Hole

Çx

(3”)

IN

OUT

Mounting Screws (x4)

VESA Plate

£ää

(4”)

Back of Display

Step 8. Attach your Display to the POS Assembly

Hook the top of the VESA plate onto
the Quickshift Mount.

Gently push the bottom of the Display
into the Mount until you hear a ‘CLICK’.

HOOK

PUSH

Back of Display

Step 9. Adjust the VESA Ball Mount

Position your Display to the desired viewing
angle, using the 40° angular movement

Tension

Plate

allowed by the VESA Ball Mount.

If the display does not hold its position,
or is too resistant, adjust the Tension Plate
(see diagram right).

To make any adjustments, use the
Tightening Tool supplied.

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 27.07.09 ©

CLICK

Loosen (-Kg)

Tighten (+Kg)

Tightening

Tool

Insert the Security Screw, and tighten
using the 2mm Allen Key supplied.

TIGHTEN

Security

Screw

2mm

Allen Key

Advanced Security Installation

These Installation Instructions secure
the POS Multi using the provided
fasteners from above thework surface.

For advanced Security Installation from
below the work surface. Please refer to
the Advanced Security Installation

Addendum.