Atdec SD-POS-HA Installation manual
SD-POS-HA
Installation Instructions
Display l POS Height Adjustable
Component Checklist
Hardware
Top Cap (x1)
VESA Plate (x1)
Installation
Template (x1)
14 Gauge
Screws (x4)
3/2.5mm
Allen Key (x1 each)
Screw Cover (x1)
POS Assembly (x1)
NOTE: Philips-head
screwdriver not supplied
M5 Grub Screw (x1)
Security Screw (x1)
(optional)
IMPORTANT INFORMATION:
! IMPORTANT - Install Spacedec POS Height Adjustable as per Installation Instructions.
! This product supports a maximum load of 20kg (44lbs).
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
! The height adjustment range (from desk level to the centre of the screen) 330-450mm (12.99"-17.72").
! The minimum thickness of the mounting surface is 15mm (0.59") when using the manufacturer supplied Hardware.
! The manufacturer accepts no responsibility for incorrect installation.
Mounting Options
Your SD-POS-HA offers 355°
of Rotation. This can also be
limited to suit a specific
application. The direction in
which you mount SD-POS-HA
will determine where the 5°
gap in rotation is located,
and how you choose to limit
the rotation.
Rotation Options
0° Rotation (Fixed)
0-90° Rotation
0-180° Rotation
0-270° Rotation
0-355° Rotation
Direction
Arrow
180
270
90
0
355
5
Gap in
Rotation
USER
OR
5
Gap
in Rotation
Direction Arrow
0
90
M4x10mm (x4)
M4x12mm (x4)
M4x16mm (x4)
Display Mounting
Screws
355
270
180
USER
Step 1. Check Components
Check you have received all parts against the component checklist and Hardware above.
Step 2. Limit Rotation
Determine the degree of rotation
A.
you require
(refer to Mounting Options above).
To limit the rotation, use the
B.
2.5mm Allen Key to insert the
supplied M5 Grub Screw into your
chosen Locking Hole until it sits
flush with the Base Plate.
NOTE: If you want the full
355° rotation, you do NOT
need to install a grub screw.
2.5mm Allen Key
M5 Grub Screw
Base Plate
LOCKING HOLES
Step 3. Locate and Secure your POS Height Adjustable
Position the Installation Template in the desired
A.
location on your work surface. Ensure the straight
edge sits perpendicular with the User’s line of
sight. Mark the center points of each of the
required holes onto the work surface with a pencil.
Drill 4 x 3mm (0.12") Pilot Holes to a depth of
B.
15mm (0.59"). Use a 45mm (1.75") hole saw to
drill the Cable Access Hole in the work surface.
Reposition SD-POS-HA with the “Direction Arrow”
C.
pointing in the direction required for your chosen
rotation. Secure the SD-POS-HA to the work surface
using the supplied 14 Gauge Screws (x4).
4x
3mm (0.12")
Pilot Holes
14 Gauge
Screws (x4)
45mm
(1.75") Cable
Access Hole
3mm (0.12")
4x
Pilot Holes
Centre for 45mm (1.75")
Cable Access Hole
USER
Direction Arrow
0
Locking Hole (Fixed)
0-90
Locking Hole
0-180
Locking Hole
0-270
INSTALLATION
TEMPLATE
Locking Hole
Step 4. Attach Screw Cover
Step 5. (Optional)
Install Monitor Security Cable
Remove the paper backing from the Screw
A.
Cover and adhere to the base as shown.
Screw Cover
B.
C.
Note: Security Cable Not Included
Step 6. Install Top Cap
Top Cap
PUSH
Step 7. Adjust Pole Height
Loosen Hand
A.
Grip.
Set to desired
B.
Height
Tighten Hand Grip
C.
to lock pole at
desired height.
Push down firmly to attach the Top Cap.
Step 8. Install Monitor Cables
Option 2: When you do not want to route the cables
PUSH
Push out to remove
A.
Cable Access Cap
below the work surface.
CABLE
ACCESS CAP
B.
OUT
Pull cables out through
Rear Cable Access Port.
Loop the Security Cable (Kensington or
similar) around the internal post of the
POS Assembly.
Feed the other end of the cable through
the POS Assembly and out the Cable
Management Hole.
After you have attached the monitor
(As directed in Step 9) install the lock to the
monitor as per the manufacturer
guidelines.
Step 8. Install Monitor Cables
ADJUST
HEIGHT
TIGHTEN
TO LOCK
LOOSEN
Hand Grip
Option 1:
Prior to attaching your monitor,
install the monitor cables.
Run them through the Front
Cable Access Port, down the
pole and out of the Cable
Access Hole in the work
surface.
Step 9. Attach the VESA Plate to your Display
There are two mounting
hole configurations:
• 75 x 75mm
• 100 x 100mm
Choose appropriate
Mounting Screws from
the Hardware supplied
to suit your Display.
100mm
75mm
Mounting Screws (x4)
VESA Plate
Top of
75mm
Display
100mm
Back of Display
IN
OUT
Step 10. Attach your Display to the POS Assembly
Hook the top of the VESA plate onto the
Quickshift Mount.
HOOK
Back of Display
Press and hold the Release Buttons. Gently
push bottom of VESA Plate into Quickshift
Mount. Release Buttons to lock in place.
PUSH
Release Button
Step 11. Adjust the VESA Ball Mount
Position your Display to the desired viewing angle using the 40°
angular movement allowed by the VESA Ball Mount.
If the display does not hold its position, or is too
resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount.
To make any adjustments, use the 3mm Allen Key
supplied. Apply half a turn at a time to each screw
on the Tension Plate to adjust evenly.
Check the display, and the adjust again if necessary.
TIGHTEN (+kg)
LOOSEN (-kg)
Installation Complete
Back of Display
Tension Plate
3mm Allen Key
(optional) Insert the Security Screw
, and
tighten using a Phillips-head Screwdriver
Phillips-head
TIGHTEN
Security Screw
Back of Display
Screwdriver
Advanced Security Installation
These Installation Instructions secure
the SD-POS-HA using the provided
fasteners from the above work surface.
For advanced Security Installation from
below the work surface. Please refer to
the
Advanced Security Installation
Addendum.
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 08.02.12
C
Loading...