Atdec SD-FS-H User manual

D Horizontal Rail
Brace

C Horizontal Rail

C Horizontal Rail

G

U Screw M8x40mm

S

U

V

Component Checklist

Installation Instructions

SD-FS-H

IMPORTANT INFORMATION:

Step 1. Install the Pole to the desk.

Step 2. Assemble Horizontal Support Rail.

! IMPORTANT - Install Spacedec Free Standing Hex as per Installation Instructions.

! This product supports a maximum load of 8kg (17.5lbs) in each screen.
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
! This product is designed to support six screens of similar weight & size when configured to use the freestanding base.
! Using less than six screens may result in the stand becoming unbalanced & unstable.
! The manufacturer accepts no responsibility for incorrect installation.

Check you have received all parts against the component checklist and Hardware.

Spacedec Freestanding Hex

A. Pole

B. Freestanding Base

C. Horizontal Rail (x4)

D. Horizontal Rail
Brace (x2)

E. Pole Cover

F. Mounting Head
L/R (x4)

G. Mounting Head
Centre (x2)

I. Pole Top
Cap (x2)

J. Spanner

L. Washer 3/8”

M. Spring
Washer 3/8”

O. Screen Mounting
Screw M4x10 (x24)

P. Screw
M8x12mm (x4)

R. Spring Washer
M6 (x3)

V. Screw M6x8mm (x4)

U. Screw M8x40mm (x8)

S. Allen Key M5

H. Cable Clip
w/ Screw (x12)

K. Bolt Through
Plate

N. Bolt 3/8”

Q. Screw
M6x15mm (x3)

T. Allen Key M6

Desk

A Pole

K Bolt Through Plate

L Washer 3/8”

M Spring Washer 3/8”

N Bolt 3/8”

A Pole

Desk

B Freestanding Base

K Bolt Through Plate

L Washer 3/8”

M Spring Washer 3/8”

N

T

Hardware:

Tools Required:

Phillips Head Screw Driver

Option 1: Bolt Through

Option 2: Freestanding (with optional security bolt)

Bolt 3/8”

Allen Key M6

Q Screw M6x15mm

1. Loosen Thumb Screw.

2. Detach Bracket to mount into Horizontal Rail.

G. Mounting Head - Centre

Screw M8x40mm

Allen Key M5

Screw M6x8mm

Mounting Head - Centre
Bracket

TIGHTEN

TIGHTEN

DETACH

TIGHTEN

TIGHTEN

R

SpringWasher M6

LOOSEN

1

2

Spacedec

Installation Complete

C

No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 18.08.11

Step 3. Install Horizontal Rail to the Pole.

Step 5. Fasten Display to Mounting Heads.

Step 6. Attach Display to Horizontal Rail.

Step 8. Cable Management

P Screw M8x12mm

S Allen Key M5

E Pole Cover

Horizontal Rail
Sub-Assembly

Pole

I

Pole Top Cap

INSERT

O Screen Mounting
Screw M4x10mm

F Mounting Head

- L/R

End
Display

TOP

Centre
Display

O Screen Mounting
Screw M4x10mm

G Mounting Head

- Centre

TOP

1

2

3

To adjust the tension of the
tilt mechanism, first remove
the cover cap to expose the
tilt nut then using the
spanner supplied, tension
the nut until the display
holds the desired position.
Replace cover cap.

H Cable Clip

Step 4. Adjust Horizontal Rail Position.

Ensure horizontal rail is attached to
vertical pole with arrow facing upwards.

Select the desired height of your rail to
suit your screen size by inserting the
screws in the various holes in the pole.

Remove rail end cap screw (3) & end cap
(2). Slide Mounting head(1) onto rail &
replace end cap.

Step 7. Adjust Display Tilt Tension.

TIGHTEN

TIGHTEN

TIGHTEN

Manage your cables by attaching the cable
clips to the rail & inserting your cables.

Cables can be routed through pole & exit
at the top, centre or bottom cable ports.

Cable Clip H