Atdec SD-DO Installation manual
SD-DO
Installation Instructions
! The Spacedec Display Quickshift Donut is to be used on 42mm and 50mm diameter poles only.
! The Manufacturer accepts no responsibility for incorrect installation.
Component Checklist
Display | Quickshift Donut
Check you have received all parts against this Component Checklist prior to installation.
Quickshift
Donut (x1)
42mm Front
Donut Insert (x1)
42mm Rear
Donut Insert (x1)
Visidec Groove
Lock (x1)
NOTE: Phillips-head
screwdriver not supplied
Step 1. Install Quickshift Donut
Select your correct product configuration: A, B, or C.
A. Use this configuration with a
standard 50mm pole
(No inserts required)
B. Use this configuration with a
Visidec 42mm extrusion
pole
Front Donut
Insert
Rear Donut
Insert
Groove
Insert
Hardware
Security
Screw (x1)
(optional)
3mm Allen
Key (x1)
5mm Allen
Key (x1)
C.
Use this configuration with a
standard 42mm pole
Front Donut
Insert
Mounting
Screws
M4x10mm
Screw (x4)
M4x12mm
Screw (x4)
M4x16mm
Screw (x4)
Rear Donut
Insert
Slide the Quickshift Donut onto the pole
(with the lever open), removing the End
Cap if necessary.
Rear groove insert must align with slot in
the Pole.
Groove
Insert
OR
Note: Ensure inserts are fitted
in correct orientation.
Arrows point
to top surface
Slide the Quickshift Donut into the desired position.
If necessary, adjust the tension between the
Quickshift Donut and the Pole using the 5mm Allen
Key supplied.
TIGHTEN
OR
Once in place, close the lever
to lock the Quickshift Donut
in the desired position.
Slot
(Visidec 42mm pole shown)
LOOSEN
WARNING: Be careful not to overtighten
CLOSE
Step 2. Remove VESA plate from Quickshift Donut
Press and hold the Release Buttons (one on either side).
Release
Button
Release
Buttons
Step 3. Attach the VESA plate to your Display
There are two mounting hole configurations:
• 75 x 75mm
• 100 x 100mm
Choose appropriate Mounting Screws
from the Hardware supplied to suit
your Display.
Top of
Display
Whilst holding the Release Buttons, remove the VESA Plate.
VESA Plate
LIFT
Mounting Screws (x4)
VESA Plate
75mm
75mm
(3”)
(3”)
100mm
(4”)
100mm
(4”)
Back of Display
Step 4. Attach your Display to the Quickshift Donut
Hook the top of the VESA plate onto
the Quickshift Mount.
Press and hold the Release Buttons. Gently
insert bottom of VESA Plate into Quickshift
Mount. Release
VESA plate
Buttons to lock
in place.
Back of Display
Step 5. Adjusting the VESA Ball Mount
Position your Display to the desired viewing angle, using the 40°
angular movement allowed by the VESA Ball Mount.
Depending on the weight of the display, it may be necessary to make
adjustments to the VESA Ball Mount. If the display does not hold its
position, or is too resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount (see diagram right).
(optional) Insert the Security Screw, and
tighten using a Phillips-head Screwdriver.
TIGHTEN
Release
Button
Phillips-head
Screwdriver
Loosen (-Kg)
Tension
Plate
To make any adjustments tension evenly using the 3mm Allen Key
supplied. Apply half a turn at a time to each screw on the Tension
Plate to adjust evenly.
Check the display, and then adjust again if necessary.
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 26.09.11 ©
3mm Allen Key
Tighten (+Kg)
Loading...