AWMS-2-4640-C | Page 1 of 11
Installation Guide
AWMS-2-4640-C
2 x 460 Arms on 400 Post with C-Clamp
COMPONENT CHECKLIST RANGE
CONTENTS
A
AWM-A46
460 Arm
(x2)
C
AWM-FC
C-Clamp
(x1)
B
AWM-P40
400 Post
(x1)
C-Clamp
Page 2
Page 3
400 Post
Page 6
Page 7
460 Arm
Page 8
Page 9
Page 10
Page 11
AWM-FC
Component Checklist
Clamp Installation
AWM-P40
Component Checklist
Post Installation
AWM-460
Component Checklist
Arm Installation
Monitor Installation
Cable Management
AWMS-2-4640-C | Page 2 of 11
AWM-FC
C-Clamp
Installation Guide
AWM-FC
C Clamp
COMPONENT CHECKLIST REQUIRED TOOLS
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with Atdec modular (AWM) products.
! The manufacturer accepts no responsibility for incorrect installation.
A
C Clamp Bracket
(x1)
B
C Clamp Plate
(x1)
C
Cover for Post
(x1)
D
Cover for Base
(x1)
E
4mm
Allen key
(x1)
F
5mm
Allen key
(x1)
• All tools supplied
A
C Clamp Bracket
(x1)
B
C Clamp Plate
(x1)
C
Cover for Post
(x1)
D
Cover for Base
(x1)
E
4mm Allen key
(x1)
F
5mm Allen key
(x1)
AWMS-2-4640-C | Page 3 of 11
1. C Clamp overview
2. Re-configure Clamp
1.1 Default - This is the “out of the box” configuration
MIN THICKNESS - 25mm ( 1”)
MAX THICKNESS - 33mm (1
5
/16”)
MIN THICKNESS - 18mm (
11
/16”)
MAX THICKNESS - 25.8mm (1”)
1.2 Inverted - The C Clamp can be reconfigured for thicker surfaces
2.1 Slide pad off 2.3 Invert pad 2.3 Slide pad back on
Fasteners
supplied
with post
Tighten
Firmly
!
3.2 Place in desired location 3.3 Slide the C Clamp bracket over the plate
and position screw tips in the indents on
the base plate
Note: You may need to un-screw the set screws
out of the plate using the allen key
3.1 Attach plate to post
3. Post mount configuration
Desk Clamp
Bracket
Mounting
surface
Pad
M8 x 16mm
Set Screw
3.4 Check the set screws are mounted in position. Also check the
desk clamp bracket is positioned tight up against the mounting
surface edge
3.5 Tighten the set screws firmly and evenly on both sides of the
desk clamp bracket.
AWMS-2-4640-C | Page 4 of 11
4. Installing the clamp cover to post
5. Base mount installation
4.1 Remove the cable cover by pulling it
straight up and out of the post. Remove
top cap if already installed
5.1 Attach plate to base
5.5 Tighten the set screws firmly and evenly on both sides of the
desk clamp bracket
5.4 Check the set screws are mounted in position. Also check the
desk clamp bracket is positioned tight up against the mounting
surface edge
4.2 Locate the C Clamp cover over the
post. Guide over the holes in the base
plate and gently apply pressure on the
cover until it clicks into place
5.2 Place the base and plate in desired
location
4.3 Re-attach the cable cover by sliding
it into the post channel. Fit the pole and
cover caps back on.
5.3 Slide the bracket onto the base plate
and position screw tips in the indents on
the base plate
Note: You may need to un-screw the set
screws out of the plate using the allen key
Fasteners
supplied
with base
Tighten
Firmly
!
!
Desk Clamp
Bracket
Mounting
surface
Pad
M8 x 16mm
Set Screw
Click!
Loading...