Atdec A F -AT-W Installation Manual

Page 1
A
(x4)
(x4)
(x4)
Wall Mounted Monitor Arm
Installation Guide
AF-AT-W
COMPONENT CHECKLIST
Arm Assembly
(x1)
Primary arm
cable cover
B
VESA
head
(x1)
C
End Cap
(x1)
Wall Plate
(x1)
Nylon Anchor
Mounting
M4 x 10mm
E
(x1)
I
Plug (x2)
L
screws
F
Secondary arm
cable cover
(x1)
J
Countersunk
Screws
M4 x 12mm
(x2)
M
Mounting
screws
M4 x 12mm
G
2.5mm
Allen key
(x1)
K
Countersunk
Screws
M6 x 50mm
(x2)
N
Mounting
screws
M4 x 16mm
H
5mm
Allen key
(x1)
O
Security Screw
M4 x 16mm
(x1)
REQUIRED TOOLS
• Power Drill
• Drill Bit
• Phillips Head Screwdriver
WEIGHT RANGE
0 - 8kg (0 - 17.6lbs)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
AF-AT-W Page 1 of 4
Page 2
1. Position Wall Plate
As a guide, it is recommended that the bottom of the Wall Plate be positioned approximately 140mm (5 1/2”) above the desktop.
140mm (5 1/2”)
Note: The wall-mounted arm provides vertical adjustment of 128mm.
128mm (5”)
2. Choose the appropriate installation procedure depending on your wall type
Masonry
Nylon Anchors
Timber Stud
Timber Stud
8mm (5/16”)
Hole
3. Mount Arm Assembly
3.1 Unlock the Locking Dial before
inserting the Arm Assembly into the Wall Plate
Locking Dial
Wall Plate
M6 x 50mm Countersunk Screw
v
3.2 Slide the Arm Assembly to the preferred height and lock to secure the arm
Locking Dial
5.5mm (1/4”) Hole
Wall Plate
3.3 Secure the End Cap with the supplied M4x12mm Countersunk Screws and 2.5mm Allen Key
M4x12mm Countersunk Screw
End Cap
2.5mm Allen Key
M6 x 50mm Countersunk Screw
Wall Plate
AF-AT-W Page 2 of 4
Page 3
4. Install VESA monitor head
4.1 Install VESA monitor head as shown
5. Mounting Monitor
5.1 Insert VESA monitor head into
the receptacle in the Arm Assembly
VESA monitor head
Screen
VESA monitor head
M4x10/12/16mm Phillips Head Mounting Screws
Optional Spacers (may be required for recessed and uneven surfaces)
5.2 OPTIONAL SECURITY SCREW Ensure the Monitor is supported, then loosen the Monitor head screw with the 5mm Allen Key and tilt screen up before installing the M4 x 16mm Security Screw into the Security Screw hole
Monitor head screw
100mm
100mm
Note: Support Screen when adjusting tilt.
6. Adjusting Height
6.1 After plugging in your cables,
install the Cable Covers.
Security Screw Hole
Arm Assembly
6.2 Lift/Lower Screen to the desired height. Move both Screen and Arm assembly together.
M4 x 16mm Security Screw
Loosen
Tighten
6.3 Lock the Lock Dial firmly.
Phillips Head Screwdriver
5mm Allen Key
AF-AT-W Page 3 of 4
Page 4
7. Cable Management
7.1 After plugging in your cables, install the Cable Covers.
Insert Cable Covers up into Lock Slots.
Lock Slot
7.3 Cable Clips and Cable Stops can be installed to further manage cables.
7.2 Push Cable Covers away from Elbow Joint to secure in place.
‘click’
‘click’
Elbow Joint
8. Adjusting the Display Bracket
Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
No Allen Key necessary No Allen Key necessary
Note: Ensure enough cable slack is given to allow for movement.
Loosen
5mm Allen Key
Tighten
Note: Support Screen when adjusting tilt.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20180206B
atdec.com | atdec.co.uk | atdec.com.au
AF-AT-W Page 4 of 4
Loading...