Atdec AF-AA Installation Manual

Page 1
AF-AA Page 1 of 4
COMPONENT CHECKLIST
B
Monitor
arm (x1)
C
(x1)
A
VESA
head
(x1)
D
Rotation
limiter
(x1)
G
Security Screw
M4 x 16mm
(x1)
H
Mounting
screws
M4 x 10mm
(x4)
I
Mounting
screws
M4 x 12mm
(x4)
J
Mounting
screws
M4 x 16mm
(x4)
E
Primary arm
cable cover
(x1)
F
Secondary arm
cable cover
(x1)
Installation Guide
AF-AA
Accessory Arm
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with the range of AF Poles and arms. ! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
WEIGHT RANGE
• Phillips Head Screwdriver
0 - 8kg (0 - 17.6lbs)
Page 2
AF-AA Page 2 of 4
1. Install VESA monitor head
2. Install arm assembly
5mm
Allen Key
Pole
Top Cap
Spacers (may be required for recessed and uneven surfaces)
VESA monitor head
Screen
M4x10/12/16mm Phillips Head Mounting Screws
1.1 Install VESA monitor head as shown.
2.1 Remove Top Cap and Allen key
from existing AF- pole product
2.4 Place arm and handgrip on to the pole
Note Ensure handgrip tab lines up with slot in pole
2.5 Turn the handgrip to fix the height of the arm and place the top cap back on to the pole
2.3 Place handgrip tab in arm assembly
100mm
100mm
Arm Assembly
2.2 OPTIONAL ROTATION LIMITER
Insert rotation limiter for 180�
rotation around mounting pole
Page 3
AF-AA Page 3 of 4
4.1 Unlock Handgrip ensuring both the screen and arm assembly are supported
4.2 Lift/Lower the Screen to the desired height. Move both Screen and Arm assembly together
4.3 Lock Handgrip firmly
4. Adjusting Height
5. Cable Management
3. Mounting Monitor
VESA monitor head
Arm Assembly
3.2 OPTIONAL SECURITY SCREW Ensure the Monitor is supported, then loosen the Monitor head screw with the 5mm Allen Key and tilt screen up before installing the M4 x 16mm Security Screw into the Security Screw hole
Note: Support Screen when adjusting tilt.
3.1 Insert VESA monitor head into the receptacle in the Arm Assembly
5mm Allen Key
Phillips Head Screwdriver
Loosen
Tighten
Security Screw Hole
M4 x 16mm Security Screw
Monitor head screw
Lock Slot
Elbow Joint
click’
click’
Elbow Joint
‘click’
‘click’
5.1 After plugging in your cables, install the Cable Covers.
Insert Cable Covers up into Lock Slots.
5.2 Push Cable Covers away from Elbow Joint to secure in place.
5.3 Cable Clips and Cable Stops can be installed to further manage cables.
Cable Stop
Cable Clip
Note: Ensure enough cable slack is given to allow for movement.
Page 4
AF-AA Page 4 of 4
Adjusting the Display Bracket
Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
5mm Allen Key
Tighten
Loosen
No Allen Key necessary No Allen Key necessaryNote: Support Screen when adjusting tilt.
5. Cable Management (Cont)
Press down firmly onto the other edge of the Cable Stop and hold. This allows the rear profile to flex in place
Insert Cable Stop on one edge of the Pole Slot
Allen Key Storage
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20180206B
Loading...