Atdec ADBS-2x1-17TC, ADBS-3x1-30T3C Installation Manual

Download

Page 1

2 x 1 Ceiling Menu Board Tilt

Installation Guide

ADBS-2x1-17TC

INSTALL GUIDELINES

TWO PERSON INSTALL RECOMMENDED.

• Read and understand Installation Safety Instructions before commencing installation.

• Atdec recommends that a professional AV installer or other suitably qualified person install this product.

• Configurations should be installed in a symmetrical manner for optimal safety.

• Place rail supports (ADB-RPJ, ADB-RUJ, ADB-WP) evenly along the length of a Rail segment to provide even loading of components.

• Place ADB-P Poles and ADB-RPJ Rail Pole Joiners directly behind the centre of each screen.

• Ensure that each ADB-R Rail is supported by at least one ADB-WP Wall Plate.

COMPONENT & PARTS CHECKLIST

220lbs 100kg

A6 A7

A10 A11

ADB-PC Pole Ceiling Fixture QTY:1

Ref Part name Qty A1 Ceiling Plate 1

A2 Plate Covers 2 A3 M8 x 70mm Screw 3 A4 M8 Washer 12 A5 M8 Nut 4 A6 Plastic Anchor 6 A7 Coach Screw 6 A8 Open Wrench 1 A9 6mm Hex Key 1 A10 M8 x 60mm Screw 1 A11 End Cap 1

REQUIRED TOOLS

• Power driver

• 13mm Hex socket

• Crosshead Screwdriver

OPTIONAL TOOLS

• Spirit Level

ADBS-2x1-17TC Page 1 of 4

Page 2

COMPONENT & PARTS CHECKLIST (cont.)

220lbs 100kg

B2B1B3 B4

ADB-RPJ Rail Pole Joiner QTY:1 Ref Part name Qty

B1 Rail-Pole Plate 1

B2 M8 x 12mm Screw 4 B3 M8 Washer 4 B4 M8 Sliding Nut 4 B5 5mm Allen Key 1 B6 6mm Allen Key 1

B5 B6

ADB-P150 150 Pole QTY:1 Ref Part name Qty

C1 Pole Ø 1.97” (50mm),

59.05” (1500mm) Long 1

220lbs 100kg

ADB-R125-S 125 Rail QTY:1

Ref Part name Qty D1 Rail, 49.21” (1250mm) 1 D2 End Cap 2 D3 M5 x 8mm Screw 2

ADB-B400T VESA 400 Tilt Brackets QTY:2

Ref Part name Qty E1 Tilt Bracket - Right 1 E2 Tilt Bracket - Left 1 E3 M5 x 15mm Screw 4 E4 M6 x 15mm Screw 4 E5 M8 x 15mm Screw 4 E6 M6 Washer 4

55lbs 25kg

E2E1

E3 E4

E5 E6

ADBS-2x1-17TC Page 2 of 4

Page 3

INSTALLATION SAfETY INSTRUCTIONS

CAUTION: THIS MOUNT IS INTENDED fOR USE ONLY UP TO THE MAXIMUM WEIGHTS INDICATED. USE WITH DISPLAYS HEAVIER THAN THE MAXIMUM INDICATED MAY RESULT IN INSTABILITY OR fAILURE CAUSING POSSIBLE INJURY, DEATH OR DAMAGE TO EQUIPMENT.

Do not attempt to install this product until all instructions and warnings have been read and properly understood. If you have any questions regarding any of the instructions or warnings, please contact Atdec customer service.

Please keep this information for future reference.

Please check carefully to make sure there are no missing or defective parts - defective parts must never be used. Never operate this mounting system if it is damaged. Return the mounting system to a service centre for examination and repair.

Atdec, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

In such cases, all guarantees will expire.

GENERAL

This product should only be installed by someone of good mechanical aptitude, who has experience with basic building construction, and fully understands these instructions. Atdec recommends that a professional AV installer or other suitably qualified person install this product. Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped. Always use an assistant or mechanical lifting device to safely lift and position equipment.

If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death both during installation and at any time thereafter.

Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.

PRODUCT LOCATION

Please pay careful attention to where this product is located. Check load capacity of wall prior to installation as some mounting surfaces (including walls, ceilings, horizontal surfaces) are not suitable for installation. Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. Installing on drywall boards alone will not support the weight of most AV equipment. If you install this product on drywall it must be securely fixed to a wooden stud, concrete block or other permanent structure behind the drywall board.

Designed for indoor use, this mount is suitable for public or home installation. If located in a public or frequently

populated area ensure that the product is out of the immediate reach of people. If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling.

When drilling holes in walls it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so.

fIXING HARDWARE

The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.

It is highly recommended that all wall fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations.

HAzARD LIMITATION

When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of product can do so unhindered by any cabling.

Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts.

Particular attention to the nature of moving parts is required especially when assembling, installing and adjusting during set up. Immediately after installations double-check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness.

Tighten screws so adaptor brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 4.5N/m or 40 in-lb maximum torque.

Correct length screws must be used. If screws don’t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

It is recommended that periodic inspections of the product and its fixing points are made to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualified person.

ADBS-2x1-17TC Page 3 of 4

Page 4

Loosen

Front Rear

Loosen all

Tighten all screws

5˚

10˚

15˚

(for concrete)

E3,4,5

A10

A11

5˚

10˚

15˚

E3,4,5

A10

A11

A10

A11

INSTALLATION INSTRUCTIONS

(for concrete)

A10

A11

Loosen

Front Rear

Loosen all

(for concrete)

E3,4,5

A10

A11

A10

A11

A10

A11

A10

A11

(for concrete)

Loosen

5. Position plate on pole and retighten screws from step 4

6. Fix safety screw

A10

Loosen all

7. Fix ADB-RPJ in centre point of rail

10. Tighten or loosen screw to raise

or lower screen height, respectively

Front Rear

Tighten all screws

8. Attach brackets to screen with supplied screws

11. Tighten safety screw

E3,4,5

A11

9. Carefully lower brackets onto the rail, one at a time.

12. Put screw into hole to set at required angular increment

5˚

10˚

15˚

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20181220A

atdec.com | atdec.co.uk | atdec.com.au

ADBS-2x1-17TC Page 4 of 4