AT-320 H323 Phone User Manual (V1.39)
AT-320 H323 Phone User Manual
¾
AT-320 H323 phone Appearance Introduction:.................................................................... 2
¾
Function Keys of AT-320 H323 Phone Introduction ............................................................... 2
¾
Features .................................................................................................................................. 3
¾
Standard and Protocol ............................................................................................................ 3
¾
Operating requirements ..........................................................................................................4
¾
Electric requirements.............................................................................................................. 4
¾
Size.......................................................................................................................................... 4
¾
Installation.............................................................................................................................. 5
¾
Configuration.......................................................................................................................... 5
¾
Phone Keypad set ................................................................................................................... 5
¾
Configured by WEB ................................................................................................................ 9
¾
Configured by PalmTool ....................................................................................................... 22
¾
Telnet Configuration ............................................................................................................. 22
¾
Upgrade AT-320 H323 phone ............................................................................................. 38
¾
Usage of the phone ............................................................................................................... 39
AT-320 H323 Phone User Manual (V1.39)
2
¾ AT-320 H323 phone Appearance Introduction:
● AT-320 H323 Phone Front Illustration (Refer to Fig 1.1):
Fig 1.1 AT-320 H323 Phone Front Illustration
¾ Function Keys of AT-320 H323 Phone Introduction:
Keys Function
LOCIP/SET
With handset hung, press this key to get local IP address of the phone
MISCAL
With handset hung, press this key to review missed number
ANSCAL
With handset hung, press this key to review received number
SPEED
Speed dial
NUMBER
With handset hung, press this key to get phone number
DIACAL
With handset hung, press this key to review dialed number
SERIP The gatekeeper ip
REDIAL/EXIT
While reviewing missed, received or dialed number, press this key to dial current
number
SPEAKER/OK
Press this key to have a call without lifting the handset
AT-320 H323 Phone User Manual (V1.39)
3
VOL+
Increase the volumes of handset or speaker; turn over the record backward
VOL-
Decrease the volumes of handset or speaker; turn over the record forward
¾ Features
¾ Hardware
● Main chip—PA1688 50MHz
● Data Memory—2MB SDRAM
● Program Memory—1or 2 MB Flash memory
● Ethernet Jack—1/2 10/100M jacks
● AC/DC adapter—Input AC100--- 230VOutput 9V DC, 1A
¾ Software
● DHCP support for LAN or Cable modem
● PPPoE support for ADSL or Cable modem
● Set phone by HTTP web browser or Telnet
● Upgrade by FTP
● Support major G.7XX ;GSM610 audio codec
● VAD(Voice active detect)
● CNG (Comfort noise generation)
● Dynamic voice jitter buffer
● G.167/165 compliant 16ms echo cancellation
● Tone generation and Local DTMF re-generation according with ITU-T
● E.164 dial plan and customized dial rules
● 100 entries for speed dial
● 80 entries each for missed calls, answered calls and dialed calls
● Adjustable volume for both handset and speaker
● Voice prompt
● Hotline
● Support adjustable user password and super password
¾ Standard and Protocol
AT-320 H323 Phone supports following standard and protocol:
AT-320 H323 Phone User Manual (V1.39)
4
● IEEE 802.3 /802.3 u 10 Base T / 100Base TX
● Major G.7XX; GSM610 audio codec
● H.323 V4
● TCP/IP: Internet transfer and control protocol
● RTP: Real-time Transport Protocol
● RTCPReal-time Control Protocol
● VAD/CNG save bandwidth
● DHCPDynamic Host Configuration Protocol
● PPPoEPPP Protocol over Ethernet
● DNSDomain Name Server
● TelnetInternet's remote login protocol
● FTPFile Transfer protocol
● TFTPFile Transfer protocol (optional)
● HTTPHyper Text Transfer protocol
● Build in H.323 proxy
¾ Operating requirements:
● Operation temperature: 0 to 50° C (32° to 122° F)
● Storage temperature: -30° to 65° C (-22° to 149° F)
● Humidity: 10 to 90% no dew
¾ Electric requirements:
● Voltage: 9V~24V
● Power adapter: output DC 12V/450mA
● Network interface:1/2X RJ-45 Ethernet Connectors
¾ Size
200 x 195 x 87 mm (L x W x H)
AT-320 H323 Phone User Manual (V1.39)
5
¾ Installation:
1 Connect handset to base: insert handset cord into handset cord jack at the left side
of the base.
2 Connect IP phone to Internet: plug the RJ-45 Ethernet cable into the Ethernet Jack.
Plug the other end of the cable into HUB. Refer to Fig 2.2 please.
Power on IP phone: plug the power cord adapter into the Power Jack. Then plug the
other end of the power cord adapter into the appropriate wall outlet.
¾ Configuration
Four different ways can be used to configure AT-320 H323 phone: phone
keypad, web browser, Telnet commands and PalmTool configuration tool on
computer.
¾ Phone Keypad setup
● Function Keys Introduction: When using keypad and LCD to configure the
settings of IP phone, following keys will be used:
Keys Function Keys Function
LOCIP/SET
Enter setting mode
SPEAKER/OK
Enter submenu; confirm change
VOL
Turn over menu
backward
VOL -
Turn over menu forward; move
cursor backward
NUMBERS
Modify values
REDIAL/EXIT
Exit current menu; exit setting mode
● Enter into settingsPlease Inputting the phone password on the keypad (If the debug
isn’t 0,the original password is 1234; If the debug is O, please use super password
1234567878) then press # for a while until there is Password stated on the
LCD , Please input the phone password again and press to
confirm. You successfully enter into settings.
Password
#
AT-320 H323 Phone User Manual (V1.39)
6
Refer to above operation; you can reach any menu to modify any value. Please refer
to following structure illustrations to learn the values of each menu item. As for the
meaning of each item and value, please refer to Web Browser Setting chapter.
● Menu Structure:
OK
AT-320 H323 Phone User Manual (V1.39)
7
AT-320 H323 Phone User Manual (V1.39)
8
AT-320 H323 Phone User Manual (V1.39)
9
¾ Configured by WEB
Double click icon to open the IE browser. Input the IP address of the phone
into address bar ( ), and then input password of the
phone into the following page. Default password 1234 is ordinary password and
super password is 12345678. With Debug set 0[disable], please input super
password; while Debug is not set as 0[disable], please input ordinary password.
Then click button. The following configured page wills popup. Refer
to Fig 3.1 please.
Fig 3.1 Http Setting
Network Setting
AT-320 H323 Phone User Manual (V1.39)
10
Fig 3.2 Network Setting
● iptype: Set how IP phone gets relevant network parameters by selecting
corresponding item from drop down list.
static ip: Select this item to authorize users set IP address, subnet mask and
router IP address of IP phone manually.
dhcp: Select this item to enable DHCP mode. With this system, your LAN or
router automatically assigns all the required network parameters to any device
connected to it when the device log on. AT-320 IP phone is shipped from the
factory with DHCP on. So, if you’re LAN or router is configured to use DHCP
addressing, the IP phone’s LAN parameters will automatically be configured as
soon as it is connected to the LAN or router and powered up.
pppoeThose ADSL and Cable Modem users please select this item for it is a
protocol especially designed for them. With this system, ADSL ISP
automatically assigns all the required IP parameters to any device connected to
it when the device log on.
modemIf the IP phone used with modem, please select this item to get
relevant network parameters auto. Then please fill ID and pin into ppp id and
ppppin fields.
● ppp id: With pppoe or modem selected in iptype drop down list, please enter
the user name here.
AT-320 H323 Phone User Manual (V1.39)
11
● ppp pin: With pppoe or modem selected in iptype drop down list, please enter
the password here.
● local ip: With static ip selected in iptype drop down list, please enter IP address
of IP phone here.
● subnet mask: With static ip selected in iptype drop down list, please enter
subnet mask of IP phone here.
● router ip: With static ip selected in iptype drop down list, please enter router IP
address of IP phone here.
● dns: With static ip selected in iptype drop down list, please enter IP address of
DNS server here.
● dns 2: With static ip selected in iptype drop down list, please enter IP address of
backup DNS server here.
● mac: MAC address is the physical address supplied by the Ethernet NIC.
AT-320 phone is shipped from the factory with a unique algorism MAC
address printed on the back of the base.
Protocol Setting
Fig 3.3 Protocol Setting
AT-320 H323 Phone User Manual (V1.39)
12
● use service: Enable/disable service by checking/clearing this box.
To make calls through gatekeeper, please check this box; otherwise, phone can
only make IP-to IP calls or calls through gateway.
● register ttl : IP phone will send a keep-alive registration message to H323
gatekeeper every “register ttl” seconds. The value range is 10-65535. Default is
60.
● jitter size : Set buffer size of RTP package. The value range is 0-32.
● service type: This option is used to accommodate the miscellaneous
requirements of the system providers. When IP phone is connected to these
systems, please select the corresponding service type.
Common: no special requirements
Mediaring: use Mediaring prepaid card
Etalk: use etalk prepaid card. When this is selected, please select
“dialnum” from the “Use dialplan” list box and put “00” into “dial
number”.
Auvtech: use Auvtech’s H.323 system. When connected with Auvtech’s
system, please select “auvtech” from the “nat traversal
” list box, select “account” from the “local type” list box.
Subcentrex: Use Subcentrex’s H.323 system
Ringtec: Use Ringtec’s H.323 system. When this is selected, please select
“dialnum” from the “Use dialplan” list box and put Ringtec account into
“dial number”.
Smartcon: Use Smartcon’s H.323 system
Dda: Use Dda’s H.323 system
Vida: Use Vida’s H.323 system
Citron: Use Citron’s H.323 system
Asiasoft: Use Asiasoft’s H.323 system
Huawei: Use Huawei’s H.323 system
AT-320 H323 Phone User Manual (V1.39)
13
Asiainfo: Use Asiainfo’s H.323 system
Lucent: Use Lucent’s H.323 system
IPN: Use IPN’s H.323 system
Yiyang: Use Yiyang’s H.323 system
Thinker: Use Thinker’s H.323 system
Suntek: Use Suntek’s H.323 system
● service addr, service id: Please put the URI (domain name/IP address : service
port) of the server into “service addr”. When the default service port is used, “:
service port” can be omitted.
If “use service” is checked, please put the URI of gatekeeper into “service
addr” .The default service port is 1719. If the gatekeeper has a GKID, please put
it into “service id”.
If “use service” is not checked, to make calls through gateway, please put the URI
of the gateway into “service addr”. To make IP-to-IP call, please clear this field.
In both cases, the default service port is 1720.
● nat traversal: When the IP phone with private IP address need communicate
with other IP phones in a different LAN or on Internet, please select an item from
dropdown list to set the proxy used by the phone.
disable: Select this item when the log in server and IP phone in the same
LAN, or the log in system supports the IP phone working behind the LAN.
enable: When the system does not support IP phone working behind the
LAN, please select this item to search public IP address of the NAT device.
With this item selected, “nat addr” field will be activated. Besides, port
mapping (port forwarding) needs to be properly set up on NAT device.
citron: With Citron private protocol used, select this item to fit into the
GnuGK system transferring the voice and signal by router.
auvtech: Select this item with Auvtech private system used.
vida: Select this item with Vida private system used.
aivgr: Select this item with aivgr private system used.
AT-320 H323 Phone User Manual (V1.39)
14
● nat addr: When “nat traversal” is set to “enable”, please put the domain name
of the servers ( These web server helps to find out the public IP of the IP phone)
into “nat addr”, such as www.whatismyip.com.
● nat ttl: When IP phone sit behind a NAT device, it will send packets to server
every “nat ttl” seconds to keep the port mapping on the NAT device alive. “nat
ttl” is an integer between 10 and 65535 .default value is 20.
● phone number: The local phone number or username of this phone, usually is
allocated by system.
● account: While calling card is set, please type the account of chosen card into
this field; while md5 account item selected in local type dropdown list, enter ID
here; while account is selected in local type dropdown list, enter H323 ID here.
While prefix item selected in use dialplan dropdown list, enter language
indicating number, card number and # here, such as 14589653185.
● pin: W hile calling card is set, please type the password of chosen card into this
field; while md5 account item selected in local type dropdown list, enter
password here. While prefix item selected in use dialplan dropdown list, enter
password and # here, such as 3185.
● register port: The local UDP port registered with server to accept incoming
handshaking messages. any number between 1024 and 65535 is acceptable.
● signal port: This port is Q.931 port using TCP protocol, can be any number
between 1024 and 65535.
● control port: This port is H.245 port using TCP protocol, can be any number
between 1024 and 65535.
● dtmf: Set DTMF signal sending way by selecting control string, inband audio,
signal keypad or rfc 2833 from list box.
● dtmf payload : When DTMF select rfc 2833.This parameter can be used
indicating type of RTP payload type. The value can be use integer 96-101.
● rtp port: RTP port is the port transferring and receiving voice packets using
UDP protocol. This is an even number between 1024 and 65535, can’t be the
same as “register port”.
● local type: This parameter refers to how IP phone authenticate itself to the
gatekeeper. The meaning of each item is as follow:
AT-320 H323 Phone User Manual (V1.39)
15
phone number: Use phone number as E.164 and H323 ID to login the GK.
account: Use phone number as E.164 and designated H323 ID filled in
account field as H323 ID to login GK.
auto: use support automated negotiate authentication account and pin about
MD5 or CAT .
md5: use MD5 authentication account and pin.
cat: use CAT authentication account and pin.
sha1: use SHA1 authentication account and pin.
● call type: Set call type by selecting the items in drop down list.
normal: Call out in normal way by selecting this item.
advanced: Call out in faststart and tunneling way by selecting this item. It is a
recommended way with H323 protocol used.
● rtp tos: Set the TOS field of the IP header of the RTP packets. The bigger this
value is 0, the higher priority the packet is .
phone settings:
Fig 3.4 Phone Setting
● use dialplan: Set whether use dial plan or use dial number by selecting the
corresponding item in drop down list.
AT-320 H323 Phone User Manual (V1.39)
16
disable: Do not use dial plan or dial number by selecting this item.
enable: Use dial plan by selecting this item.
dialnum: Use dial number by selecting this item. With this item selected,
please enter the dial prefix into dial number field.
prefix: Use 179XX service by selecting this item.
Hotline: Use Hotline function by selecting this item. With this item selected,
please enter the hotline number into dial number field.
Note With 179xx service used, please set as follows: fill call prefix into dial number
field, such as 17930; type; language indicating number, card number and # into
account field; fill password and # into pin field.
● dial number: With dialnum selected in use dialplan drop down list, please
enter the dial prefix into this field according to requirement of log in server. For
example, with eTalk card used, enter 00 here.
● ddd code: With enable or dialnum selected in use dialplan drop down list, set
area code according to E.164 dial rule. For example, Beiing 10; Shanghai 21.
● idd code: With enable or dialnum selected in use dialplan drop down list, set
country code according to E.164 dial rule. For example, China 86; U.S.A .1.
● idd prefix: With enable or dialnum selected in use dialplan drop down list,
set international call prefix according to E.164 dial rule, such as 00.
● ddd prefix: With enable or dialnum selected in use dialplan drop down list,
set long distance call prefix according to E.164 dial rule, such as 0.
Note With dialnum seletcted in use dialplan drop down list, you can also set dddcode,
AT-320 H323 Phone User Manual (V1.39)
17
iddcode, iddprefix and dddprefix according to requirement of system.
● innerline: Enable/disable innerline call by selecting corresponding items from
dropdown list.
disable: Disable call innerline by selecting this item.
enable: enable call innerline by selecting this item.
● local prefix: With enable selected in innerline dropdown list, please fill the
number switching to local call, such as 0.
● nonlocal prefix: With enable selected in innerline dropdown list, please fill the
number switching to long-distance call, such as 9.
● ring type: Set ring type by selecting corresponding item from drop down list.
dtmf 0-9: Set ring as ordinary rings in different frequency
not disturb: Set the phone do not ring by selecting this item.
pcmring: Set ring as music shipped from factory by selecting this item.
user defineSet ring as music saved by user by selecting this item.
● Use digitmap: Enable/disable digit map by checking/unchecking the box.
● Call waiting: Enable/disable call waiting by checking/unchecking the box.
● forward number: Enter receiving forwarded calls phone number into this field;
If the IP phone used with modem, with modem item selected in iptype list box,
and then fill ISP number into this field.
● fwd poweroff: Forward calls if power off by checking this box. Please enter
receiving forwarded calls phone number into fwd number field.
AT-320 H323 Phone User Manual (V1.39)
18
● fwd noanswer: Forward calls without replying by checking this box. Please
enter receiving forwarded calls phone number into fwd number field.
● fwd always: Forward all calls by checking this box. Please enter receiving
forwarded calls phone number into fwd number field.
● fwd busy: Forward calls if busy by checking this box. Please enter receiving
forwarded calls phone number into fwd number field.
● answer: Enter a number from 0 through 60 to set the entries of the seconds
before the phone answer the call auto or forward the calls.
Audio settings:
Fig 3.5 Audio Setting
● vad: Enable/disable VAD (voice activity detection).
● agc: Enable/disable AGC.
● aec: Enable/disable VEC.
● codec1: Set the priority 1of the audio compression algorithm. The options are
g729g7231g711ug711a and gsm.
● codec2: Set the priority 2of the audio compression algorithm. The options are
g729g7231g711ug711a and gsm.
● codec3: Set the priority 3of the audio compression algorithm. The options are
g729g7231g711ug711a and gsm.
● codec4: Set the priority 4of the audio compression algorithm. The options are
g729g7231g711ug711a and gsm.
● codec5: Set the priority 5of the audio compression algorithm. The options are
AT-320 H323 Phone User Manual (V1.39)
19
g729g7231g711ug711a and gsm.
● g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is 6.3kbps,
low rate is 5.3kbps.
● audio frame: Set audio frames in RTP package. Minimum is 1 and maximum is
8.
● handset in: Drag the slider to adjust the volume of handset input. Drag it to the
left to reduce the volume; while drag it to the right to increase the volume.
● handset out: Drag the slider to adjust the volume of handset output. Drag it to
the left to reduce the volume; while drag it to the right to increase the volume.
● speaker out: Drag the slider to adjust the volume of handfree output. Drag it to
the left to reduce the volume; while drag it to the right to increase the volume.
Other settings:
Fig 3.6 Other Setting
● password: Set the password of the phone. (Default password is 1234).
● super password: Set the super password of the phone.(Default super password
is 12345678).
● debug: Set the debug level of the phone.
disable: Disable output the debug message by selecting this item.
output: Output the operation information to the window, such as register,
input by selecting this item.
output all: Output all debug information and data in test window by
AT-320 H323 Phone User Manual (V1.39)
20
selecting this item.
remote debug: Save the debug information in SDRAM of IP phone by
selecting this item.
no check: Disable checking firmware tags when upgrading. This is not
suggested, because it will increase the risk of upgrading the wrong firmware
into the phone.
● upgrade addr: Put IP address or domain name obtained by ISP of FTP server
supplying upgrade program into this field.
● nts ip: Fill IP address of time server here.
● use daylight: Enable/disable daylight.
● timezone: Select correct time zone in list box.
When debug set as 0[disable], if input ordinary password (default one is 1234), then
following page will pop up after clicking . And only those parameters can
be modified.
AT-320 H323 Phone User Manual (V1.39)
21
Fig 3.7 Setting Page using ordinary pin with Debug set as 0 [disable]
● Update: Click this button to save the configuration and the phone will reboot.
Once the phone reboots successfully, the new configuration is effective.
Note After entering set page, if Update button is not clicked within 5 seconds, then
when you click it again, the index page asking for pin will pop up again. Then
please input the password again to enter the set page and then click Update
button to confirm the modification.
Phone Book:
Click this button to open the speed dial settings page. Please refer to Fig
3.7. In this page, you can set and save the speed dial number by typing the name into
the
Name
field and then entering the corresponding number following the name. For
example, input Jack in Name field following 001, and then input 5989426454 into
Phone number field. Then Jack’s number 5989426454 is saved in phone book. Then
please click
Save/Back
button. In normal state, you can use speed dial to call numbers
saved in phone book.
AT-320 H323 Phone User Manual (V1.39)
22
Fig 3.8 Phone Book Illustration
Upgrade Program: Click this button to update the program of IP phone. Before
updating, please fill IP address of FTP server into upgrade addr field, and then click
this button. Then the phone will read the corresponding bin files from the server and
then load into the phone.
Update Digitmap: Click this button to update the digitmap of the phone. Before
updating, please fill IP address of FTP server into upgrade addr field, and then click
this button. Then the phone will read the corresponding map files from the server and
then load into the phone.
Note Please refer to PalmTool User Guide to learn how to write digitmap or just
download TXT file from our site. Then please save it as “phone type.map” file,
such as pa168S.map.
¾ Configured by PalmTool
PalmTool is a tool designed especially to configure and upgrade the PA168 IP phone. On a PC
connecting with the phone or at the same segment of the phone, double click icon to open the
PalmTool. The index page of PalmTool will popup.
a) Input the IP address of the phone into
Local IP
field (such as 192.168.1.100), and
then click “Phone Settings” button.
From Version1.24, use PalmTool to set the IP phone, please set debug as output or
output all firstly, or PalmTool cannot connect IP phone. The parameters of PalmTool is
same as the parameters in HTTP, so please refer to HTTP set chapter to learn how to
set IP phone.
¾ Telnet Configuration
● On the PC choose Start>Run, and then type telnet 192.168.1.100 into Run
field in popuping Run dialog. Or input telnet 192.168.1.100 in the DOS
window. Then the following information will be displayed.
AT-320 V1.39 settings
Password :
Then please type password. With debug is set as 0[disable], if type ordinary password
(default one is 1234), after Retun, you will see
AT-320 H323 Phone User Manual (V1.39)
23
Password : ****
P:\>
If you type super password, then you will see:
Password : ********
P:\>
Above information indicates that IP phone is under setting mode, and then you can set
the AT-320 IP phone by using the telnet commands.
¾ AT-320 Telnet Commands Explanation
AT-320 Telnet Commands
Command Function
?
Supply command name and parameters
get
Display basic parameters of the AT-320 IP phone
set
Set parameters of the AT-320 IP phone
store
Save current settings to designated position
load
Load designated settings to current position
exit
Exit from the setting mode without saving the configuration
write
Exit with saving all configurations and restart AT-320
ping
Ping other net parameter
ftp
The phone connects to FTP server and then get the files
Detail description of AT-320 Telnet commands
Command ?
Syntax description: No optional parameter
Usage: Type command name and parameters following P:\> . Be used as the
keyword to supply keyword and parameters of the relevant commands.
Relevant usage: None
AT-320 H323 Phone User Manual (V1.39)
24
Detailed description:
List help of all commands
For example:
P:\>?
set
get list settings
store x store current to xth settings
load x load xth settings to current
exit
write save settings
Command get
Syntax description: No optional parameter of keywords
Usage: Display basic parameters of the AT-320 IP phone
Relevant usage: None
Detailed description:
get Display basic running parameters of the AT-320 IP phone. Input
ordinary password without debug being set as 0[disable], or input super
password with debug set as 0[disable], then following parameters of IP phone
will be displayed:
AT-320 V1.39 settings
Password: ********
P:\>get
iptype 0[static]
ip 192.168.1.100 subnetmask 255.255.255.0 router 192.168.1.254
dns 202.106.196.152 dns2 202.106.196.115 mac 00-09-45-65-a3-e6
service 1[enable]
servicetype 0[common] serviceaddr 203.93.9.57 serviceid [empty]
nattraversal 1[enable] nataddr www.showmyip.com natttl 30
phonenumber 182378009 account [empty] pin [empty]
AT-320 H323 Phone User Manual (V1.39)
25
registerport 6800 signalport 6800 controlport 6802
registerttl 60 rtptos 0 rtpport 6802
jitter size 0
calltype 1[advanced] localtype 0[phonenumber] dtmf 0[control string]
dtmfpayload 101
dialplan 2[dialnum] dialnumber 17911 dddcode [empty]
iddcode [empty] iddprefix [empty] dddprefix [empty]
innerline 1[enable] localprefix 0 nonlocalprefix 0
answer 5 ringtype 0[dtmf0] digitmap 0[disable]
fwdnumber [empty] fwdpoweroff 1[enable]
fwdalways 0[disable] fwdbusy 0[disable] fwdnoanswer 0[disable]
audiotype 0[g7231] audioframes 1 6.3k 1[enable]
vad 1[enable] agc 0[disable] aec 1[enable]
handsetin 9 handsetout 21 speakerout 21
codec1 1[g7231] codec2 0[g729] codec3 2[g711u]
codec4 4[gsm] codec5 5[null]
password 1234 superpassword 19750407 debug 1[output]
upgradeaddr [empty]
sntpip 0.0.0.0 daylight 0[disable]
timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]
Input ordinary password with debug set as 0[disable], following information will be
seen:
AT-320 V1.39 settings
Password:****
P:\>get
iptype 0[static]
ip 192.168.1.100 subnetmask 255.255.255.0 router 192.168.1.254
dns 202.106.196.152 dns2 202.106.196.115
nattraversal 1[enable] nataddr rtpport 5144
registerport 5142 signalport 5142 controlport 5144
account [empty] pin [empty]
phonenumber 182378009 fwdpoweroff 0[disable]
fwdalways 0[disable] fwdbusy 0[disable] fwdnoanswer 0[disable]
ringtype 0[dtmf0] answer 5
password 1234
upgradeaddr [empty]
sntpip 0.0.0.0 daylight 0[disable]
timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]
AT-320 H323 Phone User Manual (V1.39)
26
Command set
Syntax description: set keywords value
Usage: Used to configure password and other running parameters of AT-320 IP
phone.
Detailed description:
set iptype X
Set how IP phone gets relevant network parameters. X ranged from 0
through 3: 0: authorize users set IP address, subnet mask and router IP
address of IP phone manually; 1: use DHCP mode. With this system, your
LAN or router automatically assigns all the required network parameters to
any device connected to it when the device log on. AT-320 IP phone is
shipped from the factory with DHCP on. So, if your LAN or router is
configured to use DHCP addressing, the IP phone’s LAN parameters will
automatically be configured as soon as it is connected to the LAN or router
and powered up; 2: use PPPoE mode. Those ADSL and Cable Modem users
please select this item for it is a protocol especially designed for them. With
this system, ADSL ISP automatically assigns all the required IP parameters
to any device connected to it when the device log on; 3: use modem mode.
Those who use IP phone with modem, please set the value as 3.
set pppid XXX
With iptype set as 2, use this command to set ADSL ID; with iptype set as 3,
AT-320 H323 Phone User Manual (V1.39)
27
use this command to set Modem ID.
set ppppin XXX
With iptype set as 2, use this command to set ADSL pin; with iptype set as 3,
use this command to set Modem pin.
set ip XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP address of AT-320 IP
phone.
set subnetmask XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set subnet mask of AT-320 IP
phone.
set router XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set router IP of network with
AT-320 IP phone.
set dns XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP address of DNS server.
set dns2 XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP of backup DNS server.
set mac XX-XX-XX-XX-XX-XX
Set MAC address of the AT-320 IP phone. Parameter
xx-xx-xx-xx-xx-xx must be an HEX number.
set service X
Set register the gatekeeper or not. X ranged from 0 through 1. 0: do not
AT-320 H323 Phone User Manual (V1.39)
28
register; 1: register.
set service type X
Enable/disable the repaid and service system .choose the repaid server
provider. Parameter x ranged from 0 through 29:
0: common: disable repaid card; 4: use Mediaring service; 2: use eTalk card;
3: use Auvtech system; 5: use Ringtec service; 6: use Smartcon service; 7:
use dda service; 8: use vida service; 9: use citron system; 10: use asiasoft
system;
12: use zte system; 13: use huawei system; 16: use asiainfo system;
17: use Lucent system; 19: use IPN system; 20: use yayuang system; 21: use
thinker system; 22: use suntek system; 28: use txtc system.
set serviceaddr XXXX
Set IP address or domain name of gatekeeper.
set serviceid XXXXX
Set service ID according to required by service system.
set nattraversal X
Set NAT traversal or not. X ranged from 0 through 7: 0: do not use. When
the log in server and IP phone in the same LAN, or the log in system
supports the IP phone working behind the LAN; 1: Use NAT traversal.
When the login system does not support IP phone working behind the LAN,
please use this value to search public IP address of the NAT device. With
this item selected, please make port mapping on NAT device; 2: With Citron
private protocol used, use this value to fit into the GnuGK system
AT-320 H323 Phone User Manual (V1.39)
29
transferring the voice and signal by router; 3: use this value with Innopath
private system used; 5: use this value with vida private system used; 6: aivgr
use this value with aivgr private system used; 7: use this value with Eproxy
private system used.
set nataddr XXXXX
Set IP address of NAT device wan port or URI of free assistant service (Such
as www.showmyip.com etc.) in Internet.
NOTE The free service list of Internetwww.ip-calculator.com; www.ipchicken.com;
www.ipchicken.com;www.showmyip.com;www.whatismyip.com;
www.myipaddress.com; www.whatismyipaddress.com; ip.sbbs.net;
www.whatismyipaddress.net;checkip.dyndns.org
set natttl XX
Set NAT TTL XX is an integer between 10 and 65535 sec. default value is
20 sec.
set phonenumber XXXXXXXX
Set a phone number of AT-320 IP phone . Value xxxxx must be an Arabic
numeral and no longer than 16 characters.
set account XXXXXX
While calling card is set, set account of chosen card; while local type is set
use authentication type, set user ID; while set localtype is set as 1, set H323
ID.
set pin XXXXXXXXXX
While calling card is set, set password of chosen card; while local type is set
AT-320 H323 Phone User Manual (V1.39)
30
authentication type, set password.
set registerport XXXX
Set register port. XXXX is range from 1024 through 6553.
set signalport XXXX
This port is Q.931 port using TCP protocol. XXXX is range from 1024
through 65535.
set controlport XXXX
This port is H.245 port using TCP protocol. XXXX is range from 1024
through 65535.
set registerttl X
Set register TTL. X is range from 10 through 65535 Sec. default value is 60
Sec.
set rtptos X
Set TOS segment of IP head package in RTP digital follow.
set rtpport XXXX
RTP port is the port transferring and receiving voice flow using UDP
protocol. XXXX is range from 1024 through 65535.
set jittersize X
Set buffer size of RTP package. X is range from 0-32.
set calltype X
Set call type of the phone. X is ranged from 0 through 2: 0: call out in normal
way; 1: call out in faststart and tunneling way. It is a recommended way.
set localtype X
AT-320 H323 Phone User Manual (V1.39)
31
This command used to set how IP phone log in gatekeeper. X is ranged
from 0 through 6: 0: use phone number as E.164 and H323 ID to login the
GK; 1: use phone number as E.164 and designated H323 ID by set account
XXX command; 2:use support automated negotiate about MD5 or CAT
authentication system.3:use MD5 authentication account and pin;4: use CAT
authentication account and pin; 5: use SHA1 authentication account and pin.
set dtmf X
Set DTMF relay type. X is ranged form 0 through 3: 0:control string
1:inband audio2: signal keypad3:rfc 2833.
set dtmf payload X
When dtmf X select 3(rfc 2833).This parameter can be used indicating type
of RTP payload type. The value can be use integer 96-101.
set dialplan X
Enable/disable dial plan and dial number. Parameter X ranged from 0
through 4: 0: disable dial plan; 1: enable dial plan; 2: use dial number; 3: use
179XX service.;4: use hotline function.
set dialnumber XX
When set dialplan value set as 2, please use this command to set dial
number. For example, with eTalk card used, please set it as 00. When set
dialplan value set as 4, please use this command to set hotline number.
set dddcode XX
Set the area code when set dialplan value set as 1 or 2. For example, the area
AT-320 H323 Phone User Manual (V1.39)
32
code of Beijing is 10; the area code of Shanghai is 21, and the area code of
Chengdu is 28, etc. Parameter xxx must be an Arabic numeral and no longer
than 3 characters.
set iddcode XXX
Set the country code when set dialplan value set as 1 or 2. For example, the
country code of China is 86; the country code of USA is 1, etc. Parameter
xxxx must be an Arabic numeral and no longer than 4 characters.
set iddprefix XX
Set IDD service prefix number when set dialplan value set as 1 or 2. For
example, IDD service prefix number of china is 00; IDD service prefix
number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no
longer than 3 characters.
set dddprefix XX
Set DDD service prefix number when set dialplan value set as 1 or 2. For
example, DDD service prefix number of china is 0; DDD service prefix
number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no
longer than 3 characters.
set innerline X
Set use innerline call or not. X ranged from 0 through 1: 0: disable; 1: enable
innerline call.
set localpreifx X
With innerline set as 1[enable] , please set the number switching to local
call, such as 9.
AT-320 H323 Phone User Manual (V1.39)
33
set nonlocalprefix X
With innerline set as 1[enable] , please set the number switching to
long-distance call, such as 9.
set answer X
Set the ring seconds before the phone answers the call auto or forward the
calls. X is ranged from 0 through 60.
set ringtype X
Set types of ring. X is ranged from 0 tohrough 12: 0-9: ring as ordinary rings
in different frequency; 10: do not ring; 11: ring as music shipped from
factory; 12: ring as music saved by user
set digitmap X
Set whether to use digitmap. X ranged from 0 to 1: 0: do not use digitmap; 1:
use digitmap.
set fwdnumber XXXXXXX
Set receiving forwarded calls phone number. XXXX must be an Arabic
numeral and no longer than 16 characters
set fwdpoweroff X
Enable/disable forward calls if power off. X is ranged from 0 through 1. 0:
do not forward calls if power off; 1: forward call if power off.
set fwdalways X
Enable/disable forward all calls. X is ranged from 0 through 1. 0: do not
forward all calls; 1: forward all calls.
set fwdbusy X
AT-320 H323 Phone User Manual (V1.39)
34
Enable/disable forward calls if busy. X is ranged from 0 through 1. 0: do not
forward calls if busy; 1: forward call if busy.
set fwdnoanswer X
Enable/disable forward calls without replying. X is ranged from 0 through 1.
0: do not forward calls without replying; 1: forward call without replying.
set audioframes X
Set audio frames in RTP package. X is Arabic numerals between 0 and 7.
set 6.3k X
With G.7231, set AT-320 IP phone to use 6.3K rate or not. X is ranged
from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate.
set vad X
Enable/disable VAD. X is ranged from 0 through 1: 0: disable VAD; 1:
enable VAD.
set agc X
Enable/disable AGC. X is ranged from 0 through 1: 0: disable AGC; 1:
enable AGC.
set aec X
Enable/disable AEC. X is ranged from 0 through 1: 0: disable AEC; 1:
disable AEC.
set handsetin X
Set initial volume of handset. X is ranged from 0 through 15.
set speakerin X
AT-320 H323 Phone User Manual (V1.39)
35
Set initial volume of microphone of the base. X is ranged from 0 through 15.
set handsetout X
Set initial volume of handout. X is ranged from 0 through 31.
set codec1 X
Set the priority 1of the audio compression algorithm. X is range from 0
through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec2 X
Set the
priority 2 of the audio compression algorithm. X is range from 0
through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec3 X
Set the
priority 3 of the audio compression algorithm. X is range from 0
through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec4 X
Set the priority 4of the audio compression algorithm. X is range from 0
through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set codec5 X
Set the priority 5 of the audio compression algorithm. X is range from 0
through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.
set password XXXX
Set password of the AT-320 IP phone. XXX must be ASCII characters.
set superpassword XXXX
Set super password of the AT-320 IP phone. XXX must be ASCII
AT-320 H323 Phone User Manual (V1.39)
36
characters.
set debug X
Set open debugging message output grade for special tool. X is ranged from
0 through 5: 0: close debugging output; 1: output the operation information
to the window; 2: output all the bug information and data in test window; 3:
save the bug information into SDRAM; 4: disable checks the mark.
set upgradeaddr XXX.XXX.XXX.XXX
Set IP address or domain name of FTP server supplying upgraded
program of AT-320 IP phone.
set ntsip XXX.XXX.XXX.XXX
Set IP address of time server.
set daylight X
Set use daylight or not. X ranged from 0 through 1: 0: do not use daylight;
1: use daylight.
set timezone XX
Set time zone.
Command store
Syntax description: no keyword. Parameter ranged from 0 through 4.
Usage: Save the current settings to the designated position.
Relevant Usage: store 1
Command load
Syntax description: no keyword. Parameter ranged from 0 through 4.
Usage: Load the designated settings to the current position.
Relevant Usage: load 1
AT-320 H323 Phone User Manual (V1.39)
37
Command exit
Syntax description: no keyword and parameter
Usage: Exit from Telnet command window without saving the configuration.
Relevant usage: None
Command write
Syntax description: No keyword and parameter
Usage: Save the configuration and restart the AT-320 IP phone.
Command ping
Syntax description: ping IP address
Usage: ping IP address of other NAT device
Relevant usage: In telnet window, input ping xx.xxx.xx.xxan IP address
and return, then the result will be displayed. If the address is effective, “ping
OK” will be seen; if the address is ineffective, nothing will be seen. Fox
example:
P:\>ping 203.93.9.57
P:\>
ping OK
P:\>ping 27.56.120.56
P:\>
Note Usually, the echo time of ping command is no more than 1 second. So if the
result is not displayed in 5 seconds, ping command is fail.
ftp command
Syntax description: ftp value
Usage: the system connects to the FTP server auto to get the corresponding file
and deal with it.
Relevant usage: ftp X
X ranged from 0 through 2:
X-0: Connect to FTP Server to get the file of updating program and save it to
AT-320 H323 Phone User Manual (V1.39)
38
the SDRAM of the phone. Then the file can be read by PalmTool. This
operation aims at testing.
X-1: Connect to FTP Server to get the file of updating program and update
program Flash. This operation aims at updating program.
X-2: Connect to FTP Server to get the file of updating dial rules and update
program Flash. This operation aims at updating dial rule.
Note When you use ftp 0 and ftp 1 commands, if the file get from FTP server is too large
or the net speed is too slow, then the process will not be seen in telnet window.
Please be patient. Using ftp command in telnet to get file spends almost same
minutes as getting file using phone. So if nothing is displayed after too long time, it
means that ftp is fail.
Note All the Telnet commands of AT-320 IP phone should be written in low case and
the password is case sensitive.
¾ Upgrade AT-320 IP phone
¾ Set FTP server
FTP server can be supplied by the server provider as well as setup by the users in
LAN. Please set the IP address of FTP server.
¾ Prepare Updated program
You can ask the server provider for the latest version of program.
¾ Operation
If you have got the IP address of the FTP server from ISP, please do as follows:
a) Use keypad to enter setting mode
b) Use keypad to input the IP address of FTP server
c) Press , then No19 light will blink twice a second. Once the
phone restarts successfully, the new program is effective.
Note Please do not change the name of the upgraded program, or the
8
Local IP
AT-320 H323 Phone User Manual (V1.39)
39
operation will be fail.
¾ Usage of the phone
¾ Receiving calls:
AT-320 IP phone can receive incoming calls from other AT-320 IP phone and
devices that support the H.323 protocol. It works just like an ordinary phone for
incoming calls. When it rings, you can receive the call by following methods:
Use handset: Lift the handset and begin speaking. When the call is over, put
the handset back.
Handset to hand free: While receiving call with handset, press
on the keypad and then put down the handset. When the call is over, press
again.
Hand free: Press to speak to the other party. When the call is over,
press again.
Hand free to handset: While receiving the call with pressed
, pick up the handset to continue the call. When the call is over, put back the
handset.
Note When you communicate with the other party without lifting the handset, please
do not exceed 40 CM from speaker.
¾ Place a call
● Call another PA168 IP phone under the same Gatekeeper:
1. Handset: Pick up the handset and listen for the Internet dial tone. Then dial the
phone number you wish to call and press or to end the dialing.
Speaker
Speaker
Speaker
Speaker
Speaker
Call
AT-320 H323 Phone User Manual (V1.39)
40
Once the call connection has been established and the ring tone has sounded,
wait for the other party to answer. When the other party answers, you can
begin speaking. When the call is over, put back the handset. The dialed
number has been saved into the buffer.
2. Hand free: Press and listen for the Internet dial tone. Then input the
phone number you wish to call and press or to end the dialing.
Once the call connection has been established and the ring tone has sounded,
wait for the other party to answer. When the other party answers, you can
begin speaking. When the call is over, Press again. The dialed
number has been saved into the buffer.
3. Blind dialing: Use the keypad to enter the phone number you wish to call and
then press or to make the call. Once the call connection has
been established and the ring tone has sounded, wait for the other party to
answer. When the other party answers, you can begin speaking. When the call
is over, Press again. The dialed number has been saved into the
buffer.
● Place a call without login the Gatekeeper
If AT-320 IP phone does not login the Gatekeeper, you can place a call by lifting
the handset or pressing and then inputting the IP address of the other
party, and then pressing or
● Place a call through Gateway
If AT-320 IP phone does not login the Gatekeeper, you can place a call through
Speaker
Call
Speaker
Call
Speaker
Speaker
Call
Speaker
AT-320 H323 Phone User Manual (V1.39)
41
Gateway directly by lifting the handset or pressing and then inputting
the IP address of the other party, and then pressing or .
Note When you place a call without Gatekeeper or with Gateway, please log off
Gatekeeper. To get the detailed operation please refer to Configuration chapter.
¾ View Records
● View missed calls
Click then you will hear the record of missed call. Click
to turn the numbers orderly; click to turn the numbers
reservedly. If there is no record, you will hear nothing.
● View received call
Click then you will hear the record of the received call. Click
to turn the number orderly; click to turn the numbers reservedly.
If there is no record, you will hear nothing.
● View dialed number
Click then you will hear the record of the dialed call. Click
to turn the number orderly; click to turn the numbers
reservedly. If there is no record, you will hear nothing.
● When you hear the number you want to dial, please press to place a call
directly.
Note AT-320 IP phone supports saving 80 entries unanswered call, dialed call and
received call ranged from 1-80 at best. When the entries arrives 80, the latest
record will cover the first one. The record will be lost when the phone restarts or
turned on.
Record
Vol + Vol -
Play
Vol +
Vol -
Play
Vol +
Vol -
AT-320 H323 Phone User Manual (V1.39)
42
Appendix Table PA168S IP phone digital-character key map:
Keys Press Once Press Twice Press Thrice Press quartic Press quintic
1
1 . , ?/_ !//
2
2 A/a B/b C/c [
3
3 D/d E/e F/f ]
4
4 G/g H/h I/i *
5
5 J/j K/k L/l
6
6 M/m N/n O/o #
7
7 P/p Q/q R/r S/s
8
8 T/t U/u V/v
9
9 W/w X/x Y/y Z/z
*
.
0
0 space :/@ ;/- \ /&
#
Case change
Reserves the right to make changes in technical and product specification without
prior notice.
AT-320 H323 Phone User Manual (V1.39)
43
AT-320 H323 Phone User Manual (V1.39)
All rights reserved
Loading...