ATC Group OP XS, ATC 36 Installation Manual

Operating Instructions for OP Devices

AHT Cooling Systems GmbH – NL Deutschland

Sonntagshornstraße 19 · 83278 Traunstein · Germany · Tel. [phone] · Fax [phone] · Email [e-mail]

1 April 2008

Operating Instructions for OP Devices

AHT Cooling Systems GmbH – NL Deutschland

Sonntagshornstraße 19 · 83278 Traunstein · Germany · Tel. [phone] · Fax [phone] · Email [e-mail]

2 April 2008

Operating Instructions for OP Devices

Table of Contents

1. Safety instructions ……………………………………………………………………...……….. 4

2. Before using the device …………………………………………………………………….... 4

3. Packing ……………………………………………………………………………………..…. 4

4. General information ………………………………………………………………………….…….. 5

5. Warranty ………………………………………………………………………………………...….. 5

6. Transport, packing, location, assembly ……………………………………………………. 6

7. Storage of products ………………………………………………………………...……….. 7

8. Connecting to the power supply system………………………………………………….………. 7

9. Commissioning …………………………………………………………………………...……….. 8

10. Material and cooling agent ………………………………………………………………….… 8

11. Control unit ……………………………………………………………………………….………. 9

12. Cleaning …..………………………………………………………………………….………. 10

13. Maintenance……………………………………………………………………………….……… 11

14. Connection diagram ………………………………………………………………………….... 11

15. Exploded assembly drawing and parts list ………………………………………………….. 11

16. Name plate information ………………………………………………………………..……. 11

17. Device information (OP XS tall, OP S / Showcase, OP MP / ATC 27, OP LP / ATC 36,

OP XLP / ATC 48) ….…………............................................…...…. 12

18. Cleaning details …………………………………………………………………………… 14

19. Maintenance details …………………………………………………………………………... 14

20. Notes ……………………………………………………………………………………..……. 14

Operating instructions for OP devices (OP XS tall, OP S / Showcase, OP MP / ATC 27,
OP LP / ATC 36 and OP XLP / ATC 48), English

Subject to technical changes and misprints or typographical errors.
Dated April 2008

AHT Cooling Systems GmbH – NL Deutschland

Sonntagshornstraße 19 · 83278 Traunstein · Germany · Tel. [phone] · Fax [phone] · Email [e-mail]

3 April 2008

Operating Instructions for OP Devices

1. Safety instructions

 Pay attention during and after installation that the device is not positioned on the electric

cable!

 Always transport the device in upright position!
 If the device is slanted during transport, you must wait at least for two hours before you

start running the device in order to avoid defects!

 Pull power plug before each cleaning or maintenance

operation or interrupt power supply!

 Do not position the device next to a heat source, in supply air or in the current of hot air.
 Do not keep or store fuel, gas or other flammable substances close to the cooling unit!

There is risk of fire or explosion due to the escaping vapours.

 Keep a distance of at least 8 cm (3.2 inches) between the wall and the rear side in order

that hot air may escape upwards.

 Ventilation openings must not be blocked!
 Level the device on a solid surface area and set it up in a room which is appropriate for its

dimensions and its purpose of use.

 Do not use the cooling unit at a place where the am

bient temperature falls below 16°C

(61°F). Set up the device at a dry place.

 When setting up the device or when relocating it, pay attention not to damage the floor.
 Do not damage the refrigeration circle!
 The electric cable must only be replaced by a qualified technician!
 Do not use any extension cords or multiple plugs!
 The disconnection of the power supply must be possible by pulling the power plug or by a

two-pole switch which is switched before the socket.

 This operating instruction is part of the device. Therefore, it must remain with the device!

2. Before using the device

 Check the device for damages after unpacking. Report possible damages immediately to

the fright carrier!

 Wait for two hours before starting up the device in order that the cooling circuit is able to

achieve its entire functionality.

 The installation and the electrical connection must

be appropriately prepared by a

qualified person according to the valid regulations.

 Before starting up the device, you must clean its inside!
 Recommend professional installation and set-up!

3. Packing

 The packing material can be completely recycled and

is marked by a recycling symbol.

Dispose according to the local regulations.

 Store packing material (plastic bag, polystyrene parts, etc.) out of the range of children.

AHT Cooling Systems GmbH – NL Deutschland

Sonntagshornstraße 19 · 83278 Traunstein · Germany · Tel. [phone] · Fax [phone] · Email [e-mail]

4 April 2008

Operating Instructions for OP Devices

4. General information

This operating manual refers to several design models. The following pages detail instructions
for the operation, maintenance and cleaning of the device. The manufacturer cannot be held
liable for damages which are a result of the inappropriate application of the product. In
order to maintain warranty claims, please read and observe the information in this operating
manual.

This operating manual is valid for the following design models:

 OP XS tall
 OP S (Showcase)
 OP MP (ATC 27)
 OP LP (ATC 36)
 OP XLP (ATC 48)

I

nformation for your safety:

The construction of this cooling display was accomplished according to the safety standards of
ETL (Edison Testing Laboratories) for electrical and sanitary devices.
The device is exclusively suited for the storage and presentation of packed food or food which
has been filled in bottles or cans.

 H

ygienic guidelines: (according to ETL list)

o ETL approval according to the hygienic guidelines category II of NSF

 Electrical safety:

o (according to ETL list) ETL approval according to the guidelines for the electrical

safety UL 471 (USA and Canada)

o Declaration of Conformity for Europe CE

Responsibilities of the customer:

 Make sure that the outlet is provided with a ground terminal.
 The current and voltage must correspond to the information on the name plate of the

device.

 Pay attention that the device is positioned on a level surface.
 Read and observe the guidelines on the following pa

ges.

5. Warranty:

Due to differently formulated warranties it is not possible to make general statements here.
Warranty periods are shown separately and agreed on in our general terms and conditions, in
the order confirmation or in the purchase contracts.

Warranty exclusion:

 Use of the device at a location with a room temperature of more than 26°C (78°F)
 Use of extension cords and multiple plugs
 Inappropriate use / application
 Insufficient cleaning, maintenance and/or repair
 Inappropriate grounding
 Connection of the device to a power supply which de

name plate

viates from the instructions on the

AHT Cooling Systems GmbH – NL Deutschland

Sonntagshornstraße 19 · 83278 Traunstein · Germany · Tel. [phone] · Fax [phone] · Email [e-mail]

5 April 2008