Installation Method
A Recessed Junction box
Cover Removal
Remove the Allen Screws on
Mounting
Drill mounting holes according
Connect the electrical cables
Replace Cover
Replace the cover
NOTE: The cover is earthed
Install the two Allen Screws
Daily Use & Maintenance
If using a chemically
After turning off the power supply, remove cover and
Clean away any dirt that has deposited inside the hand
Remove the motor housing and check the brushes on the
ATC CHEETAH
Hand Dryer
First Fix
should be installed to allow
hand dryer to sit flush with the
wall. Height should be
determined from table
overleaf
either side of the hand dryer,
lift off cove. Make sure to put
the cover in a location where it
will not be damaged.
to the area that the Hand
Dryer is to be installed in (see
Overleaf) & mount the hand
dryer.
and ensure correct Polarity.
NOTE: The Sensitivity of the
Cheetah is fixed. Do not install
with anything below the dryer
that can start the dryer. E.g.
Shelves, Radiators, above sinks
etc.
External Maintenance:
• Regularly clean cover with a
soft cloth, do not use harsh
detergents, Abrasive, Acid or
Alkali Based Cleaning products
or cleaning brushes as they
may damage the cover finish.
impregnated cloth please test
on an inconspicuous area prior
to use to check suitability.
Internal Maintenance
check all connections,
dryer.
motor for wear. Replace worn Brushes.
Please note: Brushes are a consumable item and are not
covered under warranty
Method Of Operation:
Insert the back
of your hands
Turn your hands
over
Infra-Red Sensor
Rub your hands
together until dry
Z-2281 M/W/B
through the mounting screws.
Please ensure they are firmly
attached prior to re-energising
the power supply.
and test the hand dryer
Packing List
ATC Cheetah Hand Dryer User Manual
5mm Plastic wall plug x4 Allen Key
30mm Self Tapping Screws x4
Specification
230v ~ 50Hz
Sound Level
Phase
1Φ
Sensor Range
15-20cm (fixed)
Load
1475w
IP Class
IPX1
Air Speed
65m/s
Size (mm)
295x320x170
Heat level
900w
Nett Weight
4.5kg
Features
Infra-Red operated Hygienic High Speed hand dryer
Solid Stainless Steel or Painted Steel
Auto stop Function after4s to prevent overrun
Product Description
Circuit Diagram
Precautions before installation
Do not install in the following locations; Installation in these
areas can cause the unit to malfunction
Areas with Temperatures below 0oC or above 40oC
In direct Sunlight or areas above reflective surfaces
Areas where the unit can come into direct contact with
Above counters or sinks
Areas of High moisture and Humidity levels
Locations containing Corrosive or Oxidizing gasses
Areas at Altitude above 2000m
The Chart below shows the recommended mounting
Make sure the dryer is mounted more than 150mm away
Ensure the wall the hand dryer is mounted on is flat and
Do not mount the unit behind doors where the opening of
Do not install the dryer with the power connected; the
5
Voltage
75
Cover
Countersunk
Cover Screw
Allen Key
Motor Cable
Entry Hole
P.C.B
Heating Element
power ind ic at or
Infra-Red Sensor
Air outlet
Check i nd ic at or
dB@1
m
sensor plug
Environmental Protection
Waste electrical products should not be disposed
of with household waste, please recycle this
product where the facilities exist.
♻
Please check with your local authority
Warranty
ATC Electrical &Mechanical provides a 2-year limited parts
warranty for the
are followed: Installation and use of the hand dryer is in
accordance with the instruction manual, which is packed
with hand dryer.
In order to arrange parts for the hand dryer the following
information is required.
Receipt number: ____________________________________________
Z-2281 M/W/B
as long as the following conditions
water
Installation Location
height for the Hand Dryer.
from walls on either side of the dryer.
smooth.
the door may damage the dryer
dryer must be connected by a qualified electrician when
being installed.
Date of Manufacture: __________________________________________
Date of Purchase: __________________________________________
The power cord Supplying the hand dryer should be at least
1.5m² 2 Core & Earth
Loading...