Installation Method
Daily Use & Maintenance
First Fix
• A Recessed Junction box
should be installed to allow
hand dryer to sit flush with the
wall.
determined from table
overleaf
Height should be
Cover Removal
•
Remove the Allen Screws on
either side of the hand dryer,
lift off cover and disconnect
earth cable. Make sure to put
the cover in a location where it
will not be damaged.
Mounting
• Drill mounting holes according
to the area that the Hand
Dryer is to be installed in (see
Overleaf) & mount the hand
dryer.
• Connect the electrical cables
and ensure correct Polarity.
Cover
External Maintenance:
• Regularly clean cover with a
soft cloth, do not use harsh
detergents, Acid or Alkali Based
Cleaning products or cleaning
brushes as they may damage
the cover finish.
•
If using a chemically
impregnated cloth please test
on an inconspicuous area prior
to use to check suitability.
Internal Maintenance
• After turning off the power supply, remove cover and
check all connections,
•
Clean away any dirt that has deposited inside the hand
dryer and clean the air filter.
• Remove the motor housing and check the brushes on the
motor for wear. Replace worn Brushes.
Please note: Brushes are a consumable item and are not
covered under warranty
Method Of Operation:
ATC Puma
Hand Dryer
Z-2000M
Replace Cover
•
Reconnect the earth cable and
replace the cover onto the
base of the hand dryer.
Install the two Allen Screws
•
and test the hand dryer
Cover
Insert the back
of your hands
Turn your hands
over
Packing List
ATC Puma Hand Dryer
5mm Plastic wall plug x4
30mm Self Tapping Screws x4
Rub your hands
together until dry
User Manual
Allen Key
Specification
Voltage 230v ~ 50Hz Motor Brush Motor
Phase 1Φ Sensor Range 15-20cm
Load
Air Speed
Heat level
500w-1150w
60m/s Size (mm) 280x180x152
650w-750w
IP Class IPX1
Nett Weight
3.0kg
Features
• Infra-Red operated Hygienic High Speed hand dryer
•
Solid Stainless Steel
• Auto stop Function after 40s to prevent overrun
•
On/Off switch of the element for lower power usage
•
Built in air filter
Product Description
Cover
Infrared
Sensor
Speed/Element
Switch
Circuit Diagram
Infrared
Sensor
Thermal
Cut Off
Environmental Protection
Waste electrical products should not be disposed
of with household waste, please recycle this
♻
product where the facilities exist.
Please check with your local authority
Warranty
ATC Electrical &Mechanical provides a 2-year limited parts
warranty for the Z-2000M as long as the following conditions
are followed:
tallation and use of the hand dr
Ins
instruction manual, which is packed with hand dryer.
In order to arrange service fo
information is required.
Receipt number:
____________________________________________
Date of Manufacture:
__________________________________________
Date of Purchase:
__________________________________________
yer is in accordance with the
r the hand dryer the following
Precautions before installation
Do not install in the following locations; Installation in these
areas can cause the unit to malfunction
• Areas with Temperatures below 0
• In direct Sunlight or areas above reflective surfaces
• Areas where the unit can come into direct contact with
water
• Above counters or sinks
• Areas of High moisture and Humidity levels
• Locations containing Corrosive or Oxidizing gasses
Areas at Altitude above 2000m
•
o
C or above 40oC
Installation Location
• The Chart below shows the recommended mounting
height for the Hand Dryer.
• Make sure the dryer is mounted more than 150mm away
from walls on either side of the dryer.
Ensure the wall the hand dryer is mounted on is flat and
•
smooth.
Do not mount the unit behind doors where the opening of
•
the door may damage the dryer
Do not install the dryer with the power connected; the
•
dryer must be connected by a qualified electrician when
being installed.
Location of junction
box without cover
The power cord Supplying the hand dryer should be at least
1.5m² 2 Core & Earth
Loading...