ATC Electrical & Mechanical Z-1651W Installation Instructions

Distributed By

ATC Electrical & Mechanical

ATC House, Broomhill Drive

Tallaght, Dublin 24

Ireland
PH: [phone]
FX: [phone]

HAND DRYER

UK Office

ATC Electrical & Mechanical

Innovation Centre, Gallows Hill

Warwick, C V34 9PL

PH: [phone]

MODEL Z1651W/M

INSTALLATION MANUAL

EMAIL: [e-mail]

WEB: www.ATC.ie

PLEASE READ CAREFULLY THROUGH THIS MANUAL BEFORE USING THE PRODUCT. OBSERVING ALL SAFETY
INFORMATION, WARNINGS AND NOTES WILL PROTECT YOURSELF AND OTHERS.

This product is intended for installation by a qualified electrician; please obser ve al l l ocal wi ring r ules w hen i nstall ing this

If the dryer will not run

First ensure that the

breaker supplying the dryer is operational. If it is,
disconnect the power and remove the dryer cover.
Taking suitable precautions to avoid shock hazard, reconnect the power and
check for voltage at the terminal block.
If ther

,
Microcomputer
times
again.

If the dryer cycles by it
runs all the time, or is not
sensitive enough

Ensure that there is no obstruction on or in front of the infrared sensor.
Clean an

Try adjusting the sensitivity potentiometer
on Microcomputer Board (Blue
sensor range. If the problem persists, replace the Microcomputer Board

If heat element gets hot but
the fan motor does not turn

Disconnect the power. Remove the dryer cover and check for obstructions
in the fan housing. Damaged fans must be replaced. If there no obstructions,
replace the motor.

If the dryer runs but makes a
buzzing noise

Disconnect the power. Remove the dryer cover and check the fan for rubbing
on the housing as its rotates. Replace fan

If the fan motor runs but the
heat element does not get
hot (Dryer blows cold air)

Disconnect the power and remove the dryer cover. Check for loose or
damaged wires. Remove the blower housing.
see
element does not appear damaged, disconnect it at the Electric Board and
check element wire continuity

time.

If the motor makes a ticking
or whining noise when it runs

Disconnect the power, remove the dryer cover and check the brushes for
wear, replace them if necessary

Model:

Serial No.:

Distributor:

Customer:

Address:

Tel No.:

Fax. No.:

Date of Purchase:

For Seller:

Signature &Stamp:

product. Disconnect power at the Circuit breaker or main fuse before installing or servicing.
Failure to properly ground unit could result in severe electrical shock and/or death.
All units must be supplied with a 3-wire service. The ground wire must be connected to the dryer’s earthing terminal and
back plate.

NOTE

Do not install dryer over a washbasin.

If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or similar qualified person
in order to avoid a hazard. Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring
rules

SPECIFICATION

INSTALLATION

Installation Kit Included: 4pc self-threading screw, 4pc plastic dowel,1pc installation template

MOUNTING HEIGHTS (to base of the d ryer)

OPERATION

MAINTENANCE

•

•

•

•

•

•

•

•

•

•

•

•

•

1. Installation must be carried out in accordance with the current edition of the local wiring regulations. Installation

2. Place template against wall at desired height (see mounting height recommendations below) and mark the

3. Remove and retain the two security hex cover screws and cover. Then mount the hand dryer base on the wall

4. Connect the live wire (Brown) to the terminal block marked “L”.

5. Connect the neutral wire (Blue) to the terminal block marked “N”.

6. Connect the ground wire(Colored Green & Yellow) to the terminal block marked “E”.

7. Replace cover. Do not over-tighten screws.

8. Energize the supply and test for sensitivity. If the dryer sensitivity is not satisfactory, remove the cover and

Men 1200mm
Women 1160mm
Children 4-7 years
Children 8-10 years
Children 11-13 years
Children 14-16 years
Disabled Bathr oom 900mm

•

•

•

•

•

•

•

•

•

Voltage: 230V/50Hz,6.1A
Rated Power: 1400W
Air Velocity : 13M/S
Air Flow: 90M3/H
Drying Time: 30-40S
Sensor Range: 5-15CM (Manually adjustable)
Protection Level: IPX1
Stainles s St e el Electric Isolation: CLASS I
ABS Electric Isolation CLASS II
Finish: Stainless Steel or White ABS
Brush Motor: 2300 rpm
Noise at 2M: 60dB
Dimensions (HxWxD): 285 x22 5x165 mm

should be performed only by a qualified electrician.
location of the 4 mounting holes. Drill Diameter: 8mm (5/16").
using the wall plugs and fixings provided

adjust using the sensitivity potentiometer.

812mm
860mm
910mm
960mm

Automatic No-touch operation.
Shake excess water from hands.
Place hands under the outlet to start operation.
Rub hands lightly and rapidly.
Stops automatically after hands are removed.

Periodic cleaning of the unit is recommended.
Isolate power, remove cover and clean dryer interior. Remove any dust or lint.
Wipe the cover with a damp cloth and mild cleaning solution. Do not soak.
Never use abrasives to clean the cover

CIRCUIT DIAGRAM

TROUBLESHOOTING

Symptom

circuit

self ,

e is power and the dryer will not run, replace the Electric Circuit Board

Board, and/or Sensor Board. Turn the blower wheel several

by hand to see if it is blocked, if so remove blockage and test dryer

y dirt off the sensor lens.

Corrective Action

dial). Turn anti-clockwise to decrease the

if it is burnt out or broken. Damaged elements must be replaced. If the

Please check thermostat continuity on the heating element at the same

, if open circuit replace the element

if it is rubbing or damaged.

Check the heating element to

WARRANTY

This hand dryer has a 1 year warranty from the date of purchase for any manufacturing defect.
It covers replacement of defective parts except when caused by improper use of the hand dryer. This warranty is only valid if
the form card has been properly filled up with the vendor stamp.
For any warranty claim you should contact your local distributor or manufacturer.