ATC Electrical & Mechanical DPH750-ECO, DPH1500-ECO, DPH1000-ECO, DPH500-ECO Installation Instructions

ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland

IE: 01 4678301, UK:0203 564 9164, Email [e-mail]

ATC Electrical & Mechanical,

ATC ALMERIA ECO DIGITAL PANEL HEATER
INSTALLATION AND OPERATION MANUAL

DPH500-Eco 500w Digital Panel Heater
DPH750-Eco 750w Digital Panel Heater
DPH1000-Eco 1000w Digital Panel Heater
DPH1500-Eco 1500w Digital Panel Heater
DPH2000-Eco 2000w Digital Panel Heater

-1-

ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland

IE: 01 4678301, UK:0203 564 9164, Email [e-mail]

ATC Electrical & Mechanical,

CONTENTS

Contents 2

Important Safety Instructions 3

Electrical Installation notes 4

Wall Mounting Instructions 5

First Use and Setup 7

Settings Standby and Boost 8

Setting the Running Temperatures 9

Program Menu and programming 9

Keylock 11

Open Window Detection 11

Sound 11

Factory Reset 11

Battery Replacement 12

Maintenance 12

Landlord mode (Runback) 13

Runback mode settings 13

Main Runback Menu, Max Duration and Temperature Set points 14

Activating Runback and using the heater in Runback mode 15

Runback Operation Scenarios 16

Optional Castor Installation instructions 17

Technical Specifications 17

Component Diagram 18

Warranty 19

End on life and disposal information 19

EcoDesign Information 20

-2-

ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland

CAUTION

IE: 01 4678301, UK:0203 564 9164, Email [e-mail]

IMPORTANT SAFETY INSTRUCTIONS

These instructions should be carefully read before installation and retained by the user.
The booklet must be kept and delivered to the new user in case of disposal of the
heater. The Manufacturer reserves the right to vary the features of the product without
prior notice. The technical data are indicative only.

1. This heater is intended solely for the use it has been designed for, namely space
heating. The Manufacturer or Distributor is not responsible for any damage that
could happen due to improper use.

2. After unpacking make sure that the heater is complete and shows no signs of
tampering or any visible damage

3. Keep packing materials, which are potentially dangerous, away from children.

4. The heater can be used by children of at least 8 years (as well as by persons with
reduced physical, sensory or mental capabilities, or lack of experience or required
knowledge) provided that they are under supervision, or after they have been
instructed relating to the safe use and have understood the potential dangers.

5. Children should not play with the Heater.

6. Cleaning and maintenance must be performed by the user and not by unsupervised
children.

7. Children of less than 3 years should be kept away unless continuously supervised.

8. Children aged from 3 years and less than 8 years shall only switch on/o the
heater provided that it has been placed or installed in its intended normal operating
position and they have been given instruction concerning use of the heater in a safe
way and understand the hazards involved, children should always be supervised.

9. Children aged from 3 years and less than 8 years shall not plug-in, regulate, clean
the heater or perform maintenance.

10. Before connecting the heater make sure that the voltage is the same as indicated
on the device rating label.

11. Do not use in presence of gas, inflammable or explosive liquids or substances as
defined in BS5345.

12. Some fundamental rules which apply to all electrical devices
must be observed when using the heater:

• Do not touch the heater with wet hands.

• Do not handle the heater when you have bare feet.

• Do not let children play with the heater.

ATC Electrical & Mechanical,

13. Avoid the use of extension cords with this product, extension cords may overheat
and there could be a risk of fire.

14. Do not make any modification to the Heater.

15. Keep connections dry.

16. If the power supply cord is damaged, do not use the heater until the cord has been
replaced. For power cord replacement, always contact an electrician in order to
avoid any risk of injury.

-3-

ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland

IE: 01 4678301, UK:0203 564 9164, Email [e-mail]

ATC Electrical & Mechanical,

17. If the heater is not going to be used for a long period, disconnect it from the power
supply.

18. Always disconnect the heater before doing any maintenance.

19. CAUTION - Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are
present.

ELECTRICAL INSTALLATION NOTES

The installation should always be carried out by a qualified electrician or a competent
person in accordance with the current electrical standards: HD 384 CENELEC for
Mainland Europe, IEC 60446 and BS 7671 for the United Kingdom, IEC 60445(2010) &
ET101:2008 for Ireland and IEC 60364-7-708 1988 internationally.
The energy supply to the heater must always be properly earthed. The heater must be
connected to the energy supply using the provided cable.

An over voltage category III Combined Circuit breaker and Residual Current Device
(RCD) with rated earth leakage operation not exceeding 30mA must be fitted upstream
on the supply line. The circuit breaker must have a contact opening distance of at least
3 mm.

• The heaters should always be installed only using the mounting brackets provided
or optional castors if purchased separately.

• Under no circumstances turn the heater on if it is not mounted using the brackets
supplied, the original castors accessory or if the face of the heater is flat on any
surface.

• The heater must not be recessed in the ceiling. There must be enough space
around the top of the heater to ensure adequate ventilation.

• A minimum air gap of at least 100 cm should always be allowed between the top of
the heater and a ceiling or roof.

• The heater should be at least 60 cm away from any surrounding walls.

• A distance of at least 100 cm should always be left in front of the heaters to ensure
safety

• The Heater should be mounted at a minimum of 15cm to the bottom of the heater
above floor level.

• The Heater must not be located either directly below, or in front of a socket-outlet.

• The Heater must be installed so as to prevent any control switches being able to be
touched by anyone who is in the shower or bath.

• Make sure that there is no possibility of inflammable material, combustible material
or curtains coming into contact with the heater, there is a risk of fire if this happens.

DO NOT COVER THE HEATER.

NOTE: The installer should review the contents of this manual with the owner on
completion of the installation.

-4-

ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland

IE: 01 4678301, UK:0203 564 9164, Email [e-mail]

ATC Electrical & Mechanical,

WALL MOUNTING INSTRUCTIONS

Remove the heater from the packaging and then remove the wall bracket from the
back of the heater by laying the heater face down and opening the lock with a flat
screwdriver.

1) Lift the locking tab with the screwdriver, 2) Push the bracket toward the base
of the heater.

3) Lift the Top of the bracket away from 4) Remove the bracket.
the heater

Kw 0.5/.75/1.0 1.5 2.0

A 218

B 130 292 402

-5-

All dimensions in mm

ATC House, Broomhill Drive, Tallaght, D24 EF99, Ireland

CAUTION

IE: 01 4678301, UK:0203 564 9164, Email [e-mail]

ATC Electrical & Mechanical,

Note: Prior to drilling the wall, ensure there are no cables or pipes

within the wall.
After mounting the wall bracket ensure that the mounting screws are
fixed firmly to guarantee that the heater is safely mounted to the wall.

Mark the wall according to the dimensions given on the previous page for the correct
heater of your size. Drill the wall and insert the plastic wall anchors into the holes.

Mount the wall bracket using the screws provided ensuring that the screws are securely
holding the bracket to the wall and there is no movement in the bracket.

To mount the heater onto the wall, tilt the heater so the bottom holes in the rear of the
heater are aimed at the lower mounting hook and attach the heater on to the bracket
(A).

Rotate the heater towards the wall until the upper hooks enter the upper mounting
holes (B)

Push the heater down on the brackets (C) until a click is heard and the latch is in place.

-6-