Page 1
ATC SUNRAY PLUS QUICK START GUIDE
1. Control Buttons:
There are four control buttons on the sunray heater, these
buttons will change their function depending on what
mode you are in.
1
Change mode,
confirm and move to the next section, or
Access programme setting (hold for 5s)
2
Decrease Temperature/time or
Select Economy mode when programming
3
Increase Temperature/time or
Select Comfort mode when programming
4
Power on/off,
Select Frost Protection mode when
programming, or
Access the Engineering menu (hold for 5s)
2. First time operation:
In order to turn the radiator on, press the Power button (4).
The first time the radiator is turned on it will ask you to set
the time and day. If this is not done immediately then you
can set it after you have set your
program. See step 6.
The Display will change from four dashes to show the
current room temperature and
one of five operation modes, this
image shows program mode.
3. Setting the Temperature
The Comfort temperature is set while the heater is showing
the current room temperature on the display with the ‘+’ &
‘-‘ buttons (3&2). Press and hold either the ‘+’ or the ‘-'
button to begin setting the temperature, once the set
temperature starts to increase or decrease on the screen
you can release the button and start pressing ‘+’ and ‘-‘ to
set the desired temperature. Once you let go of the button
for 2s the temperature setting is saved. Note: The Economy
mode set temperature is factory set to be 3.5
o
C less than
the comfort temperature –> this can be change in the
engineering menu, see step 9 part 1 -> Engineering Menu.
4. Keypad Lock
Hold ‘+ & ‘-‘ together for 5 seconds to lock or unlock the
screen.
5. Changing Operating Modes:
The Sun Ray Plus heaters have 5 operating modes.
To change between the different modes press the Mode
button (1), each press will advance through the modes in
the following sequence:
Comfort Mode:
Full time Comfort mode shows two full
rows of bars across the bottom of the
screen and a Sun on the upper right side
of the display. As shown here.
Economy Mode:
Full time Economy mode shows one full
row of bars across the bottom of the
screen and a moon on the upper right of
the display. As shown here. Economy
temperature is factory set at 3.5
o
C less than the Comfort
setting.
Frost protection Mode:
Full time frost protection mode is factory
set at 7
o
C and is not adjustable, it is shown by a snowflake
on the right of the display. As shown here.
Program mode:
Program mode shows the numbers 1 to
7 on the left hand side of the screen
with the user set programme for the
current day at the bottom of the screen. The current day is
indicated by the arrow pointing to the numbers on the left.
The current time is indicated by the 2 flashing bars at the
bottom of the screen. As shown here.
Central Control mode:
This mode is not used. It shows a
copyright symbol in the lower right
corner. As shown here.
Central
Control
(not used)
Comfort
Economy
Frost
protection
Program
Page 2
Supplied by ATC Electrical & Mechanical
For Contact detail please visit www.ATC.ie
6. Programme Mode Detail
In the Program shown above the heater is set to run
in economy mode between midnight and 7am,
comfort mode between 7am and 7pm, and frost
protecon mode between 7pm and midnight.
7. Setting your own program
To begin programming the sunray heater
press and hold the Mode buon (1) unl
the display shows “PROG”.
There will be a small arrow poinng to the numbers on the
le hand side of the screen. These numbers are the days of
the week, 1=Monday, 2=Tuesday etc. The arrow will point
to 1 (Monday) when you begin programming.
The programme is set using the ‘+‘, ‘-’ & Power buons
(3, 2 & 4). Two flashing bars shows the hour that is to be
programmed.
To programme the radiator to run in Frost Protecon mode
for the hour indicated by the 2 flashing bars press the
power buon (4). The 2 flashing bars will move to the next
hour.
To programme the radiator to run in Economy mode for the
hour indicated by the 2 flashing bars press the ‘-‘ buon (2).
To programme the radiator to run in Comfort mode for the
hour indicated by the 2 flashing bars press the ‘+‘ buon (3)
When you have finished programming a day you can copy
the programme forward to the next day by holding in the
Mode buon unl the arrow on the le side of the screen
moves to the next number. To move to next day without
copying the programme just press the Mode buon once.
When You Have finished programming the last day of the
week press the Mode buon once to set or confirm the
me. See step 7.
IMPORTANT: Once the programming and me seng
has been completed you will need to set the heater to
operate in the program mode as outlined in step 5 Changing Operang Modes.
8. Step by Step Programme Example:
The program shown in step 5 (Programme Mode Detail) is
set by following these steps: Press and hold the Mode
buon unl you see ‘Prog’ on the screen. The arrow will be
poinng to 1 indicang you are going to set the programme
for Monday. Now press the ‘-‘ buon 7 mes to set
economy mode for (00:00-07:00), then press the ‘+’ buon
12 mes to set comfort mode for(07:00-19:00), finally press
the power buon 5 mes to set frost protecon mode for
(19:00-24:00). Monday is now programmed. To copy this
programme forward to Tuesday press and hold the Mode
buon unl the arrow moves to point to the 2 on the le
side of the screen. To move to Tuesday without copying
the programme just press the Mode buon once.
9. Setting the time.
The me can only be set the first me you turn the radiator
on or aer you have completed the programming .
When the programming has been completed for all 7 days
the display will ask for the day and me to be set. This is
indicated by the 7 numbers on the le of the screen
flashing. Select the correct day with the ‘+‘ & ‘-’ buons.
When you have the correct day, press the Mode buon.
The Hours will now flash, set the correct hour of the day
with the ‘+‘ & ‘-’ buons and press the Mode buon, the
minutes will now flash. Set the minutes in the same way
and press the Mode buon to set the me and complete
the programming.
IMPORTANT: Once the programming and me seng has
been completed you will need to set the heater to operate
in the program mode as outlined in step 4 - Changing
Operang Modes.
NOTE: The day/me seng will only be stored in the heater
for 30 minutes if the power supply is interrupted. The
Programme will be stored indefinitely.
10. Engineering Menu
To access the engineering menu press and hold the power
buon for 5 seconds. The numbers on the le side indicate
which part of the menu you are in. Press the power buon
once to move from one part to the next.
Part 1 sets how many
o
C the economy mode set temperature
is below the Comfort mode set temperature.
Part 2 sets the temperature offset –> the No. of
o
C above/
below the observed room temperature the radiator uses as
it’s current temperature.
Part 3 is to be ignored.
Part 4 sets number of seconds the backlight stays lit for.
A73020300 - 2016.02
Loading...