This MS33 BLE sensor is a type of sensor that combined
TPMS and App installed in smart phone called Nissan
ETCM. MS33 TPMS internal sensor adapts BLE low
energy transmission, let driver understand tire situation
through Nissan ETCM. When the system detects tire
pressure or temperature abnormal situation, it (APP) will
directly alarm the driver. Besides, transmission between
sensor and smart phone has been fully protected by a
well-design encryption/ decryption design. It could
provide the condition of sensor let people who with bad
intention know. Further more, there is an auto-learning
function in Nissan ETCM. All the thing need to do is to
place the smart phone in front of the driver at the left
hand side, then drive for a while. There are more
explanation about how to comply the whole process of
auto-learning position function.
About This Manual:
The information in this manual is subject to change
2.4 Balance the wheels.
2.5 Install the wheel to appropriate position of the
vehicle.
Note:
(1) Beware of the conductivity between the
sensor and valve stem.
(2) Sensors are supposed to be well locked valve
stem to avoid from leaking.
(3) Please replace original manufacturer’s
sensor battery in case voltage is below 2.7v.
(4) Sensor will transmit data every 28~32
without notice.
This manual has been created with extra care. In case
that you have any comments or questions regarding
this manual, please contact your local dealer or our
Customer Service Center.
Before operating this set, please fully understand the
prerequisite such as specifications or constraints of
the hardware and software. We are not responsible
and have no liability for any loss, damage or injury as
a result of misuse.
2. Internal Sensor
2.1 Remove the tires from the vehicle
2.2 Deflate the tires and detach the rims from the
tires.
2.3 Install the sensor on the rim with appropriate
position.(Please use 1.5~3. N-m to screw the
sensor)
Copyright (C) ATBS Technology 版權所有請勿翻印
seconds when the vehicle is running, and
when the vehicle stops, the sensor will
transmit data every 148~152 seconds.
3. Nissan ETCM APP Installation:
Nissan ETCM App is designed for Nissan Vehicle.
Through the Nissan ETCM you can know tire
temperature and pressure, sensor battery voltage, and
each sensor’s ID. At the meanwhile, it provide the autolearning position function for the driver to save time to set
Sensor ID. Besides, the connection between MS33 BLE
sensors has been encrypted, it could increase the safety
and the stabilization of data transmission.
3.1 Install APP (Take Android as example)
3.1.1 Download the APP: Nissan ETCM from Apple Store
or Google Play.
3.1.2 Turn on the APP and agree the statement.
3.1.4: Turn on the Bluetooth, and it will scan the devices
automatically.
3.1.3 Choose Sedan icon on the screen.
3.1.5 The BLE icon will light on after turning the Bluetooth
on the main page
Copyright (C) ATBS Technology 版權所有請勿翻印
3.2 App Auto Operating
For the sensor side, there are 2 way to awake the
transmission. First, using the function of auto-learning
position to pair the sensor and APP by reliable algorithm.
Place reference procedure 3.2 series Second, using
trigger to awake MS33 properly, and then enter the
sensor ID setting pages. After setting the ID properly, it
will read the tire data immediately.
3.2.1 Click “Learning ID” button below
3.2.3 Please the smart phone in front of the driver at the
front center side, then drive for about 20 to 30 minutes.
3.2.2 Press the “Auto” button, start to learn the sensor ID
automatically, at the meanwhile, the vehicle will start to
blink.
3.2.4 During the detection, the sensor ID will show on the
learning page automatically, once it complete the
detection, the learning page will show like the below
picture. Then, please press “Save” button to turn the
page to the main page
Copyright (C) ATBS Technology 版權所有請勿翻印
3.2.5 Press “Yes” button to confirm.
3.3.2 ID Edit Mode page: User could key in the sensor ID
one by one directly. Once four sensors are already,
please press “Save” button to store the ID.
Note: When the Auto Sensor ID Learning is abnormal,
please stay in the same learning page and redo 3.2
procedure again.
3.3 App Manual Operating
3.3.1Enter learning ID page, users can use “edit” or “QR
code” button to set up the ID manually before install
inflate the tire.
QR Code Mode page: User could scan the QR Code on
the MS33 to get the sensor ID one by one directly. . Once
four sensors are already, please press “Save” button to
store the ID.
Copyright (C) ATBS Technology 版權所有請勿翻印
3.3.3 Press “Yes” button to confirm.
3.4.2 Enter Sound page, users can choose the audio
alarm for the abnormal tire condition.
3.4 App Other setting
3.4.1Enter Setup page, users can set up the unit and limit
of tire pressure and temperature.
Copyright (C) ATBS Technology 版權所有請勿翻印
5. Specification
Model
MS33
Operation
Temperature
-40℃~ 125℃
Operation
Humidity
0 ~ 100%
Total
Length
72±0. 2mm
Total Height
12.4±0. 2mm
Weight
27g (±0.5g)
Battery
lifespan
Around 36 months
Battery size
CR2050W for TPMS spec
Monitoring
pressure
0 ~ 900kpa ±7Kpa ( 0-130psi ±1Psi)
Monitoring
temperature
-20℃~85℃ ±1℃
2.4GHz
Others
Continuously transmits 10 records when tire
pressure change rapidly; When a tire stops,
it transmits every 148-152 seconds. If not, it
transmits every 28-32 seconds.
5.1 MS33 Sensor
. Connect the equipment into an outlet on a circuit
different from that to which the
receiver is connected.
. Consult the dealer or an experienced radio/TV
technician for help.
FCC Caution: To assure continued compliance, any
changes or modifications not
expressly approved by the party responsible for
compliance could void the user's
authority to operate this equipment. (Example - use
only shielded interface cables
when connecting to computer or peripheral devices).
This device complies with Part 15 of the FCC Rules.
Frequency
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply
with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept
any interference received, including interference that
may cause undesired operation.
Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure
requirement, The device can be used in portable
condition without restriction.
exposure
guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of the
following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and
receiver.
Copyright (C) ATBS Technology 版權所有請勿翻印
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.