ATAS Monarch Batten Seam User Manual

ATAS INTERNATIONAL, INC.

12” Nom. Coverage

2”

2”

16” Nom. Coverage

SPECIFICATION DATA SHEET

1. PRODUCT NAME

MONARCH™ PANEL

MRB BATTEN SEAM

MRB120
MRB160

2. MANUFACTURER

ATAS INTERNATIONAL, INC.
Website: www.atas.com
Email: [e-mail]
Corporate Headquarters:
Allentown, PA 18106
Phone: [phone]
Fax: [phone]
Western Facility:
Mesa, AZ 85204
Phone: [phone]
Fax: [phone]
Southern Facility:
Maryville, TN 37801
Phone: [phone]

3. PRODUCT DESCRIPTION

Basic Uses:

Monarch panels with the Wind-Lok™ design
method are used for roong on both new
construction and re-roof applications.

Composition and Materials:

Standard Oerings:

MRB Batten Seam panels are available in .032
and .040 Aluminum and 24 gauge Metallic
Coated Steel.
Special Oerings: .050 Aluminum, 22 gauge
Metallic Coated Steel and 24 gauge 55% Al­Zn Coated Steel with acrylic coating may be
specied, subject to minimum quantities and
lead time.

Sizes and Proles:

Monarch panel is available in a Batten Seam
design. The batten and lock are an integral
part of the panel. The Batten style is either 12”
wide (MRB120), or 16” wide (MRB160). Panel
lengths are cut to customer specications,
with a minimum of 4’ and a maximum to
transportation limitations. Specify with or
without stiening ribs.

Color and Finish:

A choice of 30 colors is available in the KYNAR
500® PVDF or HYLAR 5000® PVDF nish.
(Request color chart or chips). An anodized
nish in clear or dark bronze is available as a
special oering. Texture may be smooth or
stucco embossed.

4. TECHNICAL DATA

KYNAR 500® PVDF or HYLAR 5000® PVDF
based nishes tested by paint supplier for:
Dry Film Thickness: ASTM D 1005, ASTM D
1400, ASTM D 4138 or ASTM D 5796
Specular Gloss: ASTM D 523
Pencil Hardness: ASTM D 3363
T-Bend Flexibility: ASTM D 4145
Mandrel Bend Flexibility: ASTM D 522
Impact Resistance: ASTM D 2794
Adhesion: ASTM D 3359
Water Immersion Resistance: ASTM D 870
Abrasion Resistance: ASTM D 968
Acid Resistance: ASTM D 1308
Acid Rain Resistance (Kesternich):
ASTM G 87 or DIN 50018
Salt Spray: ASTM B 117
Cyclic Salt Spray: ASTM D 5894
and ASTM D 5487
Humidity Resistance: ASTM D 2247
Accelerated Weathering: ASTM D 822 and
ASTM G 155, ASTM G 151 or ASTM G 153
Color Retention, Florida Exposure:
ASTM D 2244
Chalking Resistance: ASTM D 4214
Cleveland Condensing Cabinet:
ASTM D 4585
Cure Test, MEK Resistance: ASTM D 5402
Alkali Resistance, Sodium Hydroxide:
ASTM D 1308, Procedure 7.2
Flame Spread Rating: ASTM E 84
Organic coatings meet requirements of AAMA
2605 when applied to aluminum.
Panel testing/ratings:
Uplift: UL580 Class 90 (UL File R12113)
Air Inltration: ASTM E 283
Water Penetration: ASTM E 331
Fire Resistance: UL790/ASTM E 108
Impact Resistance: UL 2218
Load tables available upon request
Galvanized Steel: ASTM A 653
55% Al-Zn Coated Steel: ASTM A 792
Aluminum: ASTM B 209
Coil Coating: ASTM A 755
Field Tested and Approved

5. INSTALLATION

With the lock and seam being an integral
part of the panel, there are no caps or strips
to install. Field seaming of the panel is not
required. The panel is snapped onto the
previously installed panel, a clip is hooked over
the “leg” of the panel, and this is concealed by
the batten of the consecutive

panel to allow for expansion and contraction.
Minimum slope is 2:12. Installation manuals
or hands-on training via seminars are available
through ATAS. Visit www.atas.com for more
information.

6. AVAILABILITY AND COST

Availability:

Monarch panels are readily available through
ATAS product distributors. A complete line
of related components and trim accessories
is available to complete the roof system. Flat
sheet and/or coil stock in matching color
is also available for fabrication of related
accessories by the installing contractor.

Cost:

Contact ATAS product distributors for current
pricing.

7. WARRANTY
Products coated with a uoropolymer, KYNAR
500® PVDF or HYLAR 5000® PVDF nish carry
a thirty (30) year limited warranty against
cracking, peeling, chalking and fading.

8. MAINTENANCE

Monarch panels are virtually maintenance
free. Surface residue is easily removed by
conventional cleaning methods. Minor
scratches may be touched up with matching
paint, available from the manufacturer.

9. TECHNICAL SERVICES

Complete technical information and literature
are available from ATAS International, Inc.
ATAS can assist with design ideas and shop
drawings.

10. FILING SYSTEM

• www.construction.com

• www.atas.com

• Additional product information is available

from the manufacturer upon request.

MRB160

MRB120

TM

Monarch

is a trademark of ATAS International, Inc.
KYNAR 500® is a registered trademark of Arkema.
HYLAR 5000® is a registered trademark of Solvay Solexis, Inc.
© 2009 ATAS International, Inc. LRD0909 LAT711