Atari® TT030™ Hard Disk Drive
Installation Manual
Reproduction of all or any portions of this manual is not allowed without the
specific written consent of Atari Corporation.
Every
7
effort has been made to ensure the accuracy of the product documentation
in this manual. However, because Atari Corporation is constantly improving and
updating its computer hardware and software, it is unable to guarantee the
accuracy of printed material after the date of publication and disclaims liability
for changes, errors, or omissions. These documents are for repair service
information only. Part numbers are for reference only. Only parts on current
dealer parts lists are available. No license is given for any use by the possession
of these documents and may not be reproduced in any form without the written
approval of Atari Corporation.
Atari, the Atari logo, TOS, SHDRIVER.SYS, and TT030 are trademarks or
registered trademarks of Atari Corporation.
Copyright
1991.
Atari Corporation
Sunnyvale, CA
94089-1302
All rights reserved.
Atari®
TT030™
Hard
Disk
Installation Manual
Kit Contents
Your
Atari
Hard Disk
kit
should contain the
following
items:
•
Hard Disk
Drive
with Product Manual
•
Hard Disk
Drive
Cover
Assembly Part Number: CA40
1082-001
•
Hard Disk Shield Part Number:
C300835-001
•
8 Mounting Screws Part Number: C30
1333-001
•
Interface
Cable
Part Number: CA401 13
1-001
•
Power Supply
Extension
Cable
Part Number: CA400972-001
•
Installation Manual Part Number:
C302322-001
•
HDX Advanced Hard Disk Utilities Disk Part Number: CA4QQ870-QQ1
If
any of
these
components are
missing from
your
kit
please contact
the
outlet
from which
the
kit
was
ordered.
Tools Required:
Phillips
screwdriver.
*
Flat
blade (slotted)
screwdriver.
-
1
Installation
The following
steps
should
be
completed
in
the
following
order
to
install
the
hard disk
in
your
Atari
TT030
computer. Carefully
read each
step
all
the
way
through before
taking
any action required
by
that
step.
WARNING
This installation should be performed in a static free
environment.
Static can
cause
damage
to
the components
in
this
kit. Failure
to
perform
each
step
completely or
skipping
steps
could
result
in
damage
to
the hard disk or your
computer.
Mounting
the Hard
Disk
to
the
Accessory
Cover
The following
instructions pertain
to
attaching the hard disk
to
the
accessory
cover
so
that
it can
be
installed
in
the computer.
1. Remove the hard disk
from
its box.
2. Depending on
what
kind
of hard disk
you
are
installing
the
power
supply connector could be hard to access once the drive is installed in
the bracket.
If
this is the
case
install
the short
power
supply extension
cable.
If
the drive already has an extension
cable
installed
do
not
install
the one supplied with the
kit.
3.
Locate
the
SCSI
ID jumpers on the hard disk.
Refer
to
the hard disk
product
manual
for their
location.
Make sure
the
SCSI
ID jumper is
set
or drive
0.
4.
Attach the hard disk
to
the bracket assembly
as
shown
in
Figure
1 with
the four
(4)
mounting
screws.
5.
Locate
the
JTard
Disk
LED
Connector.
Refer
to
the hard disk
product
manual
for
its location.
If
the hard disk
you
are
installing
does
not
have
an
LED
connector,
skip
to step
7,
otherwise continue with this
step
and
step 6. Plug the LED cable into the LED connector on the hard disk as
shown in the Seagate ST157a example in Figure 2.
6.
Push the
LED
cable
into the
accessory cover
so
it
will
not
get
pinched
when installing the accessory cover into the computer.
2
Loading...