ATake Tumbler Quick Manual
PACKAGE CONTENTS
• ATake Tumbler Wireless Speaker
• USB power cable
• 3.5mm audio cable
• Instruction manual
- Build-in Hands-Free Speakerphone -
Welcome
Thank you for your purchase of the ATake™ Wireless Speaker. You are on your way to living a life free of wires. But first, please read this user’s guide
carefully for important information concerning operation, performance and safety.
You will find the ATake™ Wireless Speaker to be convenient, compact and easy to connect with your mobile phone, iPod touch®, iPhone™, computer, mp3
player, or any other device player must be equipped with Bluetooth A2DP stereo transmitting capabilities– if not, you may need a Bluetooth Wireless
Transmitter.
Care and maintenance
Read the following recommendations before using the ATake™ Wireless Speaker. Following these you will be able to enjoy our product for many years.
● Keep it dry and don’t take it to damp places to avoid the product’s internal circuit being affected.
● Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices,
destroy the battery or distort certain plastic parts.
● Don’t expose the product to cold areas. It may damage the internal circuit board.
● Don’t try to disassemble the product as it may get damaged if you are not professional.
● Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.
● Don’t use intensive chemical products or detergent to clean the product.
● Don’t scratch the surface with sharp things.
● Please turn off the product if you don’t use it for a long time.
NOTE:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
MADE IN CHINA
TYPE: ASP-698iS
www.atake.com
2013.02
Operating Instructions
FIGURE:
1
32
4 5 76 8 9
1. Speaker
2. Indicator (Red/Blue/Green)
3. Volume Decrease; Reject Call
4. Play/Pause; Answer/Redial
5. Volume Increase; Pairing
6. Microphone
7. Power Switch
8. Charging Port
9. Line-In Port
Indicator Denitions:
RED: Charging mode
BLUE: (quick ash) Pairing mode
BLUE:
(slow ash)
GREEN: Line-in mode
Playing mode
Charge Your BT Speaker
Make sure that your bluetooth speaker is fully charged before using it.
A full charge is approximately 2.5 hours and plays continuously 4 hours then.
1. Connect to a USB charging cable or use USB to DC adapter to charge.
2. When the LCD light indication is RED, the device is charging.
3. The LED light indication goes off when the device is fully charged.
Button Denitions:
While music playing While call incoming
Short press for
Increase
the volume.
Hold 2 seconds for
Short press for
Hold 2 seconds to
Short press for
Pairing
Play/Pause
Redial
Decrease
mode.
the last numbers
the volume. Short press for
Short press for
Answering
Rejecting
call
call
4. When the battery is low, the speaker turns off automatically after
hearing 3 monosyllabic. Please charge your speaker immediately.
Turning your bluetooth speaker on and o
Switch to turn “ON” the device. A string of tones appear and the BLUE Indicator blinks.
Switch to turn “OFF” the device. A string of tones appear and the BLUE Indicator goes off.
Pairing the bluetooth speaker with your phone
1. Activate Bluetooth on the phone.
2. Switch the bluetooth speaker ON. Hold the “ ” button for 2 seconds and hear a single tone when setting to paring mode.
3. When you turn on your bluetooth speaker for the first time, the Bluetooth-enabled phone will automatically start up in
pairing mode.
(1) The BLUE Indicator blinks quickly and a string of tones appear while pairing.
(2) Search for new devices on your phone.
(3) Choose “698”.
(4) Press ’Yes’ or ‘OK’ on the phone and confirm with PIN code 0000 (4 zeros)
4. Your phone will confirm when the pairing is complete and a single tone will appear to tell you that the bluetooth speaker is
connected.
REMARK: Every time the bluetooth speaker is switched on, it will connect to the last connected device automatically.
Remeber to turn off the device when not using it to save power.
Hands-free speakerphone
When your mobile phone rings, the call is automatically connected to your speakerphone. You can press “ ” to answer the
call , or press “ ” to reject the call. To avoid the excessive echo affecting the call quality, please adjust the speakers to the
appropriate volume during a call.
Answering incoming calls
If you receive a call while listening to music on the bluetooth speaker the music will pause. After processing the incoming call,
the music will continue to play.
Connect to other music equipment
Connect to other portable media players to the line-in port on the speaker using the supplied cable. The bluetooth will be
disconnect and the LED indicator turns GREEN while set to Line-in mode.
Troubleshooting
Q. Why can’t I hear sound from the wireless speaker?
A. Check the volume level on your Bluetooth enabled music player. Also ensure that there are no ‘barriers’ between the wireless speaker
and your paired Bluetooth® device such as walls, people or furniture as this may prevent the speaker and device from pairing successfully.
If you still can not hear sound, reset the device that you are trying to pair the speaker with. If this does not solve the issue then delete the
pairing information and brign the pairing process again.
Q. My device says ‘Bluetooth® Module not found’, what can I do?
A. This means that your device cannot find its internal Bluetooth® chip for some reason. Restarting your device should fix this problem. If
not, please contact the manufacturer of your device.
Q. My Bluetooth® device won’t pair with the speaker.
A. You need to ensure that the phone, computer or other device that you wish to connect supports the Bluetooth A2DP stereo sound
profile. The speaker will not support a mono Bluetooth® profile. Please check with your device manufacturer to ensure compatibility.
Loading...