Quick Start Guide
For Android Tablet
TC97RA1
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interfer ence to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiv er.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Caution:
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation
1
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure
to radio waves. This device is desig ne d and manufacture d no t to
exceed the emission limits for exposure to radio frequency (RF)
energy set by the Federal Communications Commission of the
U.S. Government.
The exposure standard employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set by
the FCC is 0.06 W/kg. Tests for SAR are conducted using
standard operating positions accepted by the FCC with the EUT
transmitting at the specified power level in different channels.
The highest SAR value for the device as reported to the FCC is
1.39 W/kg when placed next to the body.
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
To prevent possible hearing damage, do not listen at
high volume levels for long periods.
Package contents
Carefully unpack your box and take out the items listed
below. If any of the items are missing or damaged, please
contact your dealer immediately:
• One tablet • One AC adapter • One USB cable
• This guide
2
Tablet layout
No. Name No. Name
1 Touchscreen 5
2 Volume up/down 6 Micro SD card slot
Power button 7
3
Front facing
4
camera
Headphone jack
Micro USB DC IN /
Micro USB port
Microphone
8
3
No. Name No. Name
1 Rear facing camera 3 Volume up/down
2 Power button 4 Speaker
4
Charging your tablet
If your tablet is just being unpacked from the box, you need
to charge the tablet first. It will take around 4 to 5 hours to be
fully charged.
1. Plug the USB head of the cable into the adapter.
2. Plug the micro-USB head of the cable - with the side
marked with “B” or an icon facing down - into the
micro-USB port on your tablet.
3. Plug the adapter into a wall-socket.
5
Powering ON/OFF your tablet
To power on your tablet
Press and hold the power button
down until the screen turn on.
To power off your tablet
To turn off your tablet, follow these steps:
1. Press and hold the Power Lock button.
2. The Power-off menu appears as shown below. Touch
Power off.
3. Touch OK to power down your tablet.
6
Inserting a storage card
Your tablet supports micro-SD
cards with maximum storage
space up to 32G. You can insert
the micro SD card and pull it out
without powering down the
tablet. To do so, follow the steps
below.
Install your Micro SD Card
1. Hold your tablet with front side up.
You can find the micro SD card slot on the same
side with the power button. (For detail, see page 4)
2. Insert your micro SD card in the direction as shown.
Remove your Micro SD Card
1. Push and release the micro SD card. This will
unlock the card.
2. Pull out the micro SD card.
7
Specifications
z Intel® Bay Trail-T Z3735F
Processor
Memory
Storage
Wireless
Touchscreen
Cameras
Battery
Input/Output
z Base 1.33 GHz, Burst to 1.83GHz
z 2 MB L2 Cache
z DDR3L- 1333
z Default 2 GB
z eMMC v4.5.1
z Default: 16GB (for KK 4.4)
z Default:: 16GB (for Win8.1)
z Wi-Fi 802.11 b/g/n
z Bluetooth 4.0
z 9.7-inch Retina Display
z 10-point multi-touch
z Front: 2.0M
z Rear: 5.0M
z 1Cell , 1S3P
z Li-polymer
z 8400 mAh
z Model No.:
z 1 x micro-USB 2.0 OTG port
z 1 x Mic/head phone jack combo
z 1 x micro-SD card slot (32G max)
z 1 x Analog MIC
(2048 x 1536)
(Type B)
8
Speaker &
Mic
AC-Adapter
Dimension
(mm)
Weight
z Build-in Speaker x 2
z Analog MIC x 1
z DC Output: 5V/2A
z Input Voltage: 100 - 240VAC
z Input Frequency: 47 - 63Hz
z Model No.:
z 242.5 (W) x 179 (H) x 9.6 (D)
z 464 g (w/o adapter)
9
Loading...