This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of a shielded-type power cord is required in order to meet FCC
emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded
cables to connect I/O devices to this equipment. You are cautioned that changes or
modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the
Federal Register, National Archives and Records Administration, U.S. Government Printing Office.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
For use with AC Adaptor Model ADP-45GB (Pour Utiliser Avec Modele ADP-45GB)
Power Safety Requirement
Products with electrical current ratings up to 6A and weighing more than 3Kg must use approved power
cords greater than or equal to: H05VV-F, 3G, 0.75mm2 or H05VV-F, 2G, 0.75mm2.
2
Safety Statements
Nordic Cautions (for Notebook PC with Lithium-Ion Battery)
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions. (English)
VORSICHT! Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben
oder einem vom Hersteller empfohlenem ähnlichen T yp. Entsorgung gebrauchter Batterien nach Angaben
des Herstellers. (German)
ADVARSELI! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. (Danish)
VARNING! Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. (Swedish)
VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu. V aihda paristo ainoastaan laitevalmistajan
sousittelemaan tyyppiin. Hävitä käytetty paristo valmistagan ohjeiden mukaisesti. (Finnish)
ATTENTION! Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer
uniquement avec une batterie du mêre type ou d’un type équivalent recommandé par le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du fabricant. (French)
ADVARSEL! Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en
tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens
instruksjoner. (Norwegian)
(Japanese)
Macrovision Corporation Product Notice
This product incorporates copyright protection technology that is protected by method claims of certain
U.S.A. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by MacrovisionCorporation. Reverse engineering or disassembly is prohibited.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration
implemented regulations for laser products on August 2, 1976. These regulations apply to laser products
manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States.
WARNING: Use of controls or adjustments or performance of procedures other than
those specified herein or in the laser product installation guide may result in hazardous radiation exposure.
3
Safety Statements
Safety Precautions
WARNING! The following safety precautions will increase the life of the Notebook PC.
Follow all precautions and instructions. Except as described in this manual, refer all
servicing to qualified personnel. Do not use damaged power cords, accessories, or
other peripherals. Do not use strong solvents such as thinners, benzene, or other
chemicals on or near the surface.
Disconnect the AC power and remove the battery pack(s) before cleaning. Wipe the Notebook PC using
a clean cellulose sponge or chamois cloth dampened with a solution of nonabrasive detergent and a few
drops of warm water and remove any extra moisture with a dry cloth.
DO NOT place on uneven or unstable
work surfaces. Seek servicing if the casing has been damaged.
DO NOT place or drop objects on top
and do not shove any foreign objects into
the Notebook PC.
DO NOT press or touch the display panel.
Do not place together with small items that
may scratch or enter the Notebook PC.
DO NOT expose to strong magnetic or
electrical fields.
DO NOT leave the base of the Notebook
PC on the lap or any part of the body for an
extended period while the Notebook PC is
turned ON or is charging in order to prevent
discomfort or injury from heat exposure.
DO NOT expose to or use near
liquids, rain, or moisture. DONOT use the modem during an
electrical storm.
DO NOT expose to dirty or dusty
environments. DO NOT operate
during a gas leak.
DO NOT expose to extreme temperatures above 50˚C (122˚F) or to direct
sunlight. Do not block the fan vents!
DO NOT expose to extreme temperatures (below 0˚C (32˚F), other wise the Notebook PC may not boot.
DO NOT throw batteries in fires
as they may explode. Check local
codes for special battery disposal
instructions.
4
Safety Statements
Transportation Precautions
T o prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is
turned OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not
transport the Notebook PC while the power is still ON. Close the display panel and check that it is
latched securely in the closed position to protect the keyboard and display panel.
Remove Floppy Disks
Whether you have an internal or external 1.44MB floppy disk drive, make sure it does not contain a
diskette when transporting the floppy disk drive. When a diskette is inserted into the floppy disk drive,
the eject button protrudes out. If you attempt to transport the floppy disk drive with a diskette in the
drive, you risk damaging the eject button and also risk scratching the surface of the diskette when the
floppy disk drive is jolted.
Cover Your Notebook PC
Use a carrying case such as the one supplied with your Notebook PC to protect it from dirt, water,
shock, and scratches.
NOTE: The surface glaze is easily dulled if not properly cared for. Be careful not to rub
or scrap the Notebook PC surfaces when transporting your Notebook PC.
Charge Your Batteries
If you intend to use battery power, be sure to fully charge your battery pack and any optional battery
packs before going on long trips. Remember that the power adapter charges the battery pack as long as
it is plugged into the computer and an AC power source. Be aware that it takes much longer to charge
the battery pack when the Notebook PC is in use.
Airplane Precautions
Contact your airline if you want to use the Notebook PC on the airplane. Most airlines will have restrictions for using electronic devices. Most airlines will allow electronic use only between and not during
takeoffs and landings.
CAUTION! There are three main types of airport security devices: X-ray machines
(used on items placed on conveyor belts), magnetic detectors (used on people walking through security checks), and magnetic wands (hand-held devices used on people
or individual items). Y ou can send your Notebook PC and diskettes through airport Xray machines. However, it is recommended that you do not send your Notebook PC or
diskettes through airport magnetic detectors or expose them to magnetic wands.
5
Safety Statements
CTR 21 Approval (for Notebook PC with built-in Modem)
Danish
Dutch
English
Finnish
French
German
Greek
Italian
Portuguese
Spanish
Swedish
6
Table of Contents
UL Safety Notices
Required for UL 1459 covering telecommunications (telephone) equipment intended to be electrically
connected to a telecommunication network that has an operating voltage to ground that does not exceed
200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with the National
Electrical Code (NFPA 70).
When using the Notebook PC modem, basic safety precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons, including the following:
• Do not use the Notebook PC near water, for example, near a bath tub, wash bowl, kitchen sink or
laundry tub, in a wet basement or near a swimming pool.
• Do not use the Notebook PC during an electrical storm. There may be a remote risk of electric shock
from lightning.
• Do not use the Notebook PC in the vicinity of a gas leak.
Required for UL 1642 covering primary (nonrechargeable) and secondary (rechargeable) lithium batteries for use as power sources in products. These batteries contain metallic lithium, or a lithium alloy,
or a lithium ion, and may consist of a single electrochemical cell or two or more cells connected in
series, parallel, or both, that convert chemical energy into electrical energy by an irreversible or reversible chemical reaction.
• Do not dispose the Notebook PC battery pack in a fire, as they may explode. Check with local codes for
possible special disposal instructions to reduce the risk of injury to persons due to fire or explosion.
• Do not use power adapters or batteries from other devices to reduce the risk of injury to persons due
to fire or explosion. Use only UL certified power adapters or batteries supplied by the manufacturer
or authorized retailers.
7
Table of Contents
Contents
Safety Statements2
Federal Communications Commission Statement........................................................ 2
Canadian Department of Communications Statement..................................................2
Power Safety Requirement ........................................................................................... 2
Nordic Cautions (for Notebook PC with Lithium-Ion Battery)........................................ 3
You are reading the Notebook PC User ’s Manual. This User ’s Manual provides information on the
various components in the Notebook PC and how to use them. The following are major sections of this
User’s Manuals:
1. Introducing the Notebook PC
Introduces you to the Notebook PC and this User’s Manual.
2. Knowing the Parts
Gives you information on the Notebook PC’s components.
3. Getting Started
Gives you information on getting started with the Notebook PC.
4. Using the Notebook PC
Gives you information on using the Notebook PC’s components.
5. Configuring the BIOS
Gives you information on configuring the BIOS software.
6. Appendix
Introduces you to optional accessories and gives additional information.
Notes For This Manual
This User’s Manual was created using Macintosh versions of Adobe® PageMaker™ 6.52, Adobe
Photoshop™ 5.5, Adobe® Illustrator® 8.0, and Macromedia® Freehand™ 8.0.1. The body text type used
in this manual is “Times” (MAC) or “Times New Roman” (Windows™) and headings are “Helvetica”
(MAC) or “Arial” (Windows™). A few notes and warnings in bold are used throughout this guide that
you should be aware of in order to complete certain tasks safely and completely. These notes have
different degrees of importance as described below:
WARNING! Information to prevent
damage to components, damage to
data, or personal injury.
CAUTION! Information on actions that
must be avoided to prevent damage to
components, damage to data, or personal injury.
T ext enclosed in < > or [ ] represents a key on the keyboard; do not actually type the <
> or [ ] and the enclosed letters.
TIP: Tips and useful information for
power (advanced) computer users.
NOTE: Tips and information to aid in
completing a task.
®
12
2. KNOWING THE PARTS
Top Side
Bottom Side
Left Side
Right Side
Rear Side
Front Side
12
2
Knowing the Parts
Top Side
Refer to the diagram below to identify the components on the top side of the Notebook PC.
Display Panel
Microphone
Instant
Launch Keys
Optional
MP3 Module
Status Indicators
(described on front side)
Power Switch
Keyboard
Touchpad
Touchpad
Buttons
Opening the Display Panel
One spring-loaded latch on the front of the Notebook PC locks the display panel in the closed position
when the Notebook PC is not in use. To open the display panel, slide the latch to the right with your
thumb and lift up on the display panel at the same time. This design allows a single hand to be used
when opening the display panel. Slowly tilt the display panel forward or backward to a comfortable
viewing angle.
14
WARNING! When opening, do not force the display panel down to the table or else the
hinges may break! Never lift the Notebook PC by the display panel!
Knowing the Parts
Display Panel
The display panel functions the same as a desktop monitor. The Notebook PC uses an active matrix
TFT LCD, which provides excellent viewing like that of desktop monitors. Unlike desktop monitors,
the LCD panel does not produce any radiation or flickering, so it is easier on the eyes.
Display Panel Care
The LCD screen is very delicate and requires careful handling. Pay attention to the following precautions:
• When not in use, keep the display panel closed to prevent dust accumulation.
• Do not use chemical cleaners on the screen. Wipe only with a dry cloth or tissue.
• Do not put your fingers or any objects directly on the screen.
• Do not press or lay any objects on the machine when it is closed.
• Do not carry the Notebook PC with small or sharp objects (e.g. paper clips or staples) that may
enter the Notebook PC and scratch the display panel.
The built-in microphone provides a source for general note taking, voicemail recording, or for use with
Internet phone software. An external microphone connection is also provided for use with your own
audio input device.
Power Switch
The power switch allows powering ON and OFF the Notebook PC and recovering from STD. Push the
switch once to turn ON and once to turn OFF the Notebook PC. To prevent accidental turning OFF the
power, it is designed to take longer (about 4 seconds) to turn OFF the power.
Keyboard
The keyboard provides full-sized keys with comfortable travel (depth at which the keys can be depressed) and palm rest for both hands. T wo W indows™ function keys are provided to help ease navigation in the Windows™ operating system. The keyboard (except Fn) is also used to recover from STR.
Touchpad and Buttons
The touchpad with its buttons is a pointing device that provides the same functions as a desktop mouse.
A software-controlled scrolling function is available after setting up the included touchpad utility to
allow easy Windows or web navigation.
15
2
Knowing the Parts
Bottom Side
Refer to the diagram below to identify the components on the bottom side of the Notebook PC.
Name Card
Holder
Hard Drive
Compartment
Reset Button
Cooling Fan
& Vent
Battery
Compartment
L
Battery Release
& Lock
L
MP3 Module Release
(MP3 Module is Optional)
MP3
L
L
WARNING! The bottom of the Notebook PC (especially between the battery and hard
drive compartments, and cooling fan) can get very hot. Be careful when handling the
Notebook PC while it is in operation or recently been in operation. High temperatures
are normal during charging or operation. DO NOT PUT THE NOTEBOOK PC ON THE
LAP OR OTHER PARTS OF THE BODY TO AVOID INJURY FROM THE HEAT.
16
Knowing the Parts
The following describes the components on the bottom side of the Notebook PC as shown by the
illustration on the previous page.
Hard Drive Compartment
The hard drive compartment has a cover that is secured by the hard drive cover screw . When the cover
is removed, the Notebook’s PC hard disk drive can be seen. This design allows easy hard disk drive
swapping or upgrading.
Cooling Fan & Vent
The cooling fan turns ON when the temperature rises past a set threshold. The bottom vent brings
outside air into the Notebook PC. Do not block the vent!
Reset Button
reset
The reset button is used for rebooting the Notebook PC if <CTRL><ALT><DEL> or turning OFF the
power does not respond. To use this function, momentarily depress the button within the hole with a
pen and the Notebook PC will reboot. Do not use a pencil since the tip may break off in the hole.
Battery Compartment
The battery compartment’s surface is actually combined with the battery pack in order to reduce thickness. When the battery is released, the compartment cover and battery pack will be seen as a single unit.
The battery pack cannot be further disassembled and must be replaced as a single unit.
2
Battery Release
The battery release is a spring loaded latch that automatically locks the battery pack when inserted.
Usage details described in battery section later in this manual.
3
M
P
MP3 Module Lock
When the latch is slid towards the L icon, the MP3 module is locked in place . When the latch is slid
L
towards the
before using or transporting the Notebook PC.
icon, the MP3 module is unlocked and slightly ejected out. The lock must be secured
17
2
Knowing the Parts
Left Side
Refer to the diagram below to identify the components on the left side of the Notebook PC.
1394
DC IN
Mic-In
DC Power
Input Jack
DC IN
DC Power Input Jack
IEEE
1394
Port
Air
Vent & Fan
Fast
IrDA
Port
USB
Audio In
The supplied power adapter converts AC power to DC power for use with this jack. Power supplied
through this jack supplies power to the Notebook PC and charges the internal battery pack. To prevent
damage to the Notebook PC and battery pack, use the supplied power adapter.
4
3
9
1
IEEE1394 Port
Head-Out
Also known as iLINK (Sony) or FireWire (Apple). IEEE1394 is a high speed serial bus like SCSI but
has simple connections and hot-plugging capabilities like USB. The interface IEEE1394 has a bandwidth of 100-400 Mbits/sec and can handle up to 63 units on the same bus. It is very likely that IEEE1394,
together with USB, will replace Parallel, IDE, SCSI, and EIDE ports. IEEE1394 is also used in highend digital equipment and should be marked “DV” for Digital Video port.
Air Vent & Cooling Fan
The cooling fan turns ON when the temperature rises past a set threshold. The cooling fan is an extra
feature needed for upgrading to faster processors in the future. The air vents allow cool air to enter and
warm air to exit the Notebook PC. Do not block the air vents or else overheating may occur!
Fast Infrared Port (IrDA)
The fast infrared (IrDA) communication port allows convenient wireless data communication with
infrared-equipped devices or computers up to 4 Mbits/sec. This allows easy wireless synchronization
with PDAs or mobile phones and even wireless printing to printers. If your office supports IrDA networking, you can have wireless connection to a network anywhere provided there is a direct line of
sight to an IrDA node. Small of fices can use IrDA technology to share a printer between several closely
placed Notebook PCs and even send files to each other without a network.
USB Port
Universal Serial Bus (USB) supports many USB compatible devices such as keyboards, pointing devices, video cameras, modems, hard disk drives, printers, monitors, and scanners connected in a series
up to 12Mbits/sec. USB allows up to 127 devices to run simultaneously on a single computer, with
peripherals such as USB keyboards and some newer monitors acting as additional plug-in sites or hubs.
USB supports hot-swapping of devices so that peripherals can be connected or disconnected while the
Notebook PC is ON.
18
Knowing the Parts
Audio In
Audio input allows feeding in audio from another source in order to listen to it using the Notebook PC’s
speakers or to use it for digital multimedia files.
Microphone Jack (Mic-In)
The mono microphone jack can be used to connect an external microphone or output signals from audio
devices. Using this jack automatically disables the built-in microphone.
Headphone Jack (Head-Out)
The stereo headphone jack is used to connect the Notebook PC’s audio out signal to amplified speakers
or headphones. Using this jack automatically disables the built-in speakers.
Right Side
Refer to the diagram below to identify the components on the right side of the Notebook PC.
2
Battery
Compartment
The following describes the components on the right side of the Notebook PC as shown by the illustration above.
PC Card
Eject
PC Card
(PCMCIA)
Sockets
Hard Drive
Compartment
PC Card (PCMCIA) Sockets and Eject
Two PCMCIA 2.1 compliant sockets for two type I/II or one type III PC card is available. The socket
supports 32-bit CardBus. This allows accommodation of all Notebook PC expansion options such as
memory cards, ISDN, SCSI, and wireless network adapters.
Battery Compartment (see Bottom Side)
Hard Drive Compartment (see Bottom Side)
19
2
Knowing the Parts
Rear Side
Refer to the diagram below to identify the components on the rear side of the Notebook PC.
K
Kensington
Lock Port
®
(RJ-45)
LAN
Port
Modem
Port
(RJ-11)
External
Monitor
Port
Parallel
Port
AiBox
Docking
Port
PS/2
Port
USB
Port
The following describes the components on the rear side of the Notebook PC as shown by the illustration above.
Kensington® Lock Port
K
The Kensington® lock port allows the Notebook PC to be secured using Kensington® compatible Notebook PC security products. These security products usually include a metal cable and lock that prevent
the Notebook PC to be removed from a fixed object. Some security products may also include a motion
detector to sound an alarm when moved.
LAN Port
The RJ-45 LAN port supports an RJ-45 Ethernet cable. The internal LAN supports 10Base-T or 100BaseTX standard or duplex networks. The built-in connector allows convenient use without a dongle.
Modem Port
The RJ-11 telephone port supports an RJ-11 telephone cable. The internal modem supports up to 56K
V.90 transfers. The built-in connector allows convenient use without a dongle.
WARNING! The built-in modem does not support the voltage used in digital phone
systems. Do not connect the modem port to a digital phone system or else damage
will occur to the Notebook PC.
External Monitor Port
The 15-pin D-sub monitor port supports a standard VGA-compatible device such as a monitor or projector to allow viewing on a larger external display.
20
Knowing the Parts
Parallel Port
The 25-pin D-sub parallel/printer port supports parallel devices such as a printer or a removable drive.
AiBox Docking Port
The docking port is for connection to an AiBox portable module bay. More details given later.
PS/2 Port
The PS/2 port is for connecting an external PS/2 mouse or PS/2 keyboard to the Notebook PC if you do
not want to use the built-in pointing device and keyboard. Simultaneous use of two PS/2 devices requires an optional PS/2 Y-adapter. It is recommended that you use either a USB mouse or a USB
keyboard so that dual PS/2 connections are not required.
USB Port
Universal Serial Bus (USB) supports many USB compatible devices such as keyboards, pointing devices, video cameras, modems, hard disk drives, printers, monitors, and scanners connected in a series
up to 12Mbits/sec. USB allows up to 127 devices to run simultaneously on a single computer, with
peripherals such as USB keyboards and some newer monitors acting as additional plug-in sites or hubs.
USB supports hot-swapping of devices so that peripherals can be connected or disconnected while the
Notebook PC is ON.
2
21
2
Front Side
Refer to the diagram below to identify the components on the front side of the Notebook PC.
Display Panel Latch
M
Left
Speaker
MP3
Module
(optional)
Status Indicators
Right
Speaker
Left/Right Speaker
The built-in stereo speakers allow you to separately hear left and right channel audio without additional
attachments. The multimedia sound system features an integrated digital audio controller that produces
rich, vibrant sound in high quality 16-bit stereo. All audio features are software controlled.
3
M
P
MP3 Player Module (optional)
The MP3 player module allows the playing of MP3 files or playing/recording voice messages in a
convenient pocket-sized device. (The MP3 player module cannot record while docked in the Notebook
PC.) There is a brief introduction at the end of the hardware sections (before the BIOS section). There
is also a separate User’s Manual that comes with the MP3 Player Module.
Status Indicators
Status indicator details are described in section 3.
Display Panel Latch
One display panel latch is used to lock the display panel in the closed position. To open the display
panel, slide the latch to the right with your thumb and lift up the display panel at the same time.
22
3. GETTING STARTED
Installing/Removing Battery Pack
Using the Battery Pack
Operating Systems
Power Connection
Powering ON The Notebook PC
Power Management - Stand By/Hibernate
Restarting or Rebooting
Powering OFF The Notebook PC
Instant Launch Keys and Status Indicators
Using the Keyboard
22
3
Getting Started
Installing and Removing the Battery Pack
Your Notebook PC may or may not have its battery pack installed. If your Notebook PC does not have
its battery pack installed, there will be a large opening at the bottom of the Notebook PC. Use the
following procedures to install or remove the battery pack.
To install the battery pack:
1. Insert the battery pack with the connector first
2. Snap the battery pack into the Notebook PC
and lock the battery by moving the switch to
.
L
L
To remove the battery pack:
1. Unlock the battery by moving the switch to L.
L
You must push down and hold to slide the switch out of the lock position.
2. Lift up on the two tabs as indicated by the arrows.
3
P
M
L
L
L
L
3
P
M
L
3
P
M
L
L
24
WARNING! Never attempt to remove the battery pack while the Notebook PC is turned
ON, as this may result in the loss of working data.
WARNING! Only use battery packs and power adapters supplied with this Notebook
PC or specifically approved by the manufacturer or retailer for use with this model.
Getting Started
Using the Battery Pack
Before you use your Notebook PC on the road, you will have to charge the battery pack. The battery
pack begins to charge as soon as the Notebook PC is connected to external power. Fully charge the
battery pack before using it for the first time. A new battery pack must completely charge before the
Notebook PC is disconnected from external power. The battery pack is fully charged when the battery
charge light turns OFF. It takes a few hours to fully charge the battery when the Notebook PC is turned
OFF and may take twice the time when the Notebook PC is turned ON.
Battery Care
The Notebook PC’s battery pack, like all rechargeable batteries, has a limit on the number times it can
be recharged. Fully draining and charging the battery once a day every day will last over a year but how
long beyond that will depend on your environment temperature, humidity , and how your Notebook PC
is used. It is ideal that the battery be used in a temperature range between 10˚C and 29˚C (50˚F and
85˚F). You must also take into account that the Notebook PC’s internal temperature is higher than the
outside temperature. Any temperatures above or below this range will shorten the life of the battery.
But in any case, the battery pack’s usage time will eventually decrease and a new battery pack must be
purchased from an authorized dealer for this Notebook PC. Because batteries also have a shelf life, it is
not recommended to buy extras for storing.
3
Operating Systems
This Notebook PC may offer (depending on territory) its customers the choice of a pre-installed operating system such as Microsoft Windows ME (Millennium Edition) or W indows 2000. The choices
and languages will depend on the territory. The levels of hardware and software support may vary
depending on the installed operating system. Operating systems not pre-installed on this Notebook PC
may produce different results than the ones described in the provided user’s manuals. The stability and
compatibility of other operating systems cannot be guranteed.
Support Software
This Notebook PC comes with a support CD that provides BIOS, drivers and applications to enable
hardware features, extend functionality , help manage your Notebook PC, or add functionality not provided by the native operating system. If updates or replacement of the support CD is necessary , contact
your dealer for web sites to download individual software drivers and utilities.
The support CD contains all drivers, utilities and software for all popular operating systems including
those that have been pre-installed. The support CD does not include the operating system itself. The
support CD is necessary even if your Notebook PC came pre-configured in order to provide additional
software not included as part of the factory pre-install.
A recovery CD is optional and includes an image of all the drivers and utilities included on the factory
installed hard drive as well as the operating system itself. The recovery CD provides a comprehensive
recovery solution that quickly restores the Notebook PC’s operating system and software to its original
working state provided that your hard disk drive is in good working order. Contact your retailer if you
require such a solution.
25
3
Getting Started
Power Connection
Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the
power cord to any 110V-120V as well as 220V-240V outlets without setting switches or using power
converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a different standard. Most hotels will provide universal outlets to support dif ferent power cords as well as voltages. It is always best to ask an experienced traveler about AC outlet
voltages when bringing power adapters to another country.
TIP: You can buy travel kits for the Notebook PC that includes power and modem
adapters for almost every country.
With the AC power cord connected to the AC-DC converter , connect the AC power cord to an AC outlet
(preferably with surge-protection) and then connect the DC plug to the Notebook PC. Connecting the
AC-DC adapter to the AC outlet first allows you to test the AC outlet’s power and the AC-DC converter
itself for compatibility problems before connecting the DC power to the Notebook PC. The green
power LED on the adapter lights up if the power is within accepted ranges.
WARNING! Damage may occur if you use a different adapter to power the Notebook
PC or use the Notebook PC’s adapter to power other electrical devices. If there is
smoke, burning scent, or extreme heat coming from the AC-DC adapter, seek servicing. Seek servicing if you suspect a faulty AC-DC adapter . You may damage both your
battery pack(s) and the Notebook PC with a faulty AC-DC adapter.
26
NOTE: This Notebook PC may come with either a two or three-prong plug depending
on territory. If a three-prong plug is provided, you must use a grounded AC outlet or
use a properly grounded adapter to ensure safe operation of the Notebook PC.
1394
DC IN
DC Power Plug
AC-DC
Converter
Connect this end of the
power cord to the
AC-DC converter
Plug the “AC Power
Cord” into an
electrical outlet
Getting Started
Powering ON The Notebook PC
The Notebook PC’s power -ON message appears on the screen followed by a short beep when you turn
it ON. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS
Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. If you
press the [Esc] button during the splash screen, standard boot information such as the BIOS version can
be seen. You will also be presented with a boot menu that allows you to select bootup from “Legacy
Devices”, “Hard Drive”, “AT API CD-ROM Drive”, or enter BIOS setup. Use the up and down cursors
to make your selection and press [Enter] to execute.
WARNING! Never turn OFF or reset your Notebook PC while the hard disk or floppy
disk is in use and the activity LED is flashing; doing so can result in loss or destruction of your data. To protect the hard disk drive, always wait at least 5 seconds after
turning OFF your Notebook PC before turning it back ON.
NOTE: Before bootup, the display panel flashes when the power is turned ON. This is
part of the Notebook PC’s test routine and is not a problem with the display.
3
The Power-On Self Test (POST)
When you turn ON the Notebook PC, it will first run through a series of software-controlled diagnostic
tests called the Power-On Self Test (POST). The software that controls the POST is installed as a
permanent part of the Notebook PC’s architecture. The POST includes a record of the Notebook PC’s
hardware configuration, which is used to make a diagnostic check of the system. This record is created
by using the BIOS Setup program. If the POST discovers a difference between the record and the
existing hardware, it will display a message on the screen prompting you to correct the conflict by
running BIOS Setup. In most cases the record should be correct when you receive the Notebook PC.
When the test is finished, you may get a message reporting “No operating system found” if the hard
disk was not pre-loaded with an operating system. This indicates that the hard disk is correctly detected
and ready for the installation of a new operating system.
The S.M.A.R.T. (Self Monitoring and Reporting Technology) checks the hard disk drive during POST
and gives a warning message if the hard disk drive requires servicing. If any critical hard disk drive
warning is given during bootup, backup your data immediately and run W indows disk checking program.
T o run W indow’s disk checking program: (1) right-click any hard disk drive icon in “My Computer”, (2)
choose Properties, (3) click the Tools tab, (4) click Check Now, (5) select a hard disk drive, (6) select
Thorough to also check for physical damages, and (7) click Start. Third party disk utilities such as Symantec’s
Norton Disk Doctor can also perform the same functions but with greater ease and more features.
WARNING! If warnings are still given during bootup after running a software disk
checking utility, you should take your Notebook PC in for servicing. Continued use
may result in data loss.
27
3
Getting Started
Power Management - Stand By & Hibernate
Power management settings can be found in the Windows control panel.
The following shows the power options properties in Windows ME. You
can define Stand By or Power Off for closing the display panel, pressing
the power button, or activating sleep mode. Basically Stand by and Hibernate saves power when your Notebook PC is not in use by turning OFF
certain components. When you resume your work, your last status (such
as a document scrolled down half way or email typed half way will reappear as if you never left. Power Off will close all applications and ask if
you want to save your work if any are not saved.
Stand By is the same as Suspend-to-RAM (STR). This function stores
your current data and status in RAM while many components are turned
OFF. Because RAM is volatile, it requires power to keep (refresh) the
data.
Hibernate is the same as Suspend-to-Disk (STD) and stores your current
data and status on the hard disk drive. By doing this, RAM does not have
to be refreshed and power consumption is greatly reduced but not completely elimanated because certain wake-up components like LAN and
modem needs to remain powered.
Restarting or Rebooting
After installing drivers (please see the “Drivers and Utilities Guide”), installing applications, or making configuration changes, you may be prompted to restart the system to update the operating system
and complete the installation process. To restart the system, click the Start button and select ShutDown | and choose Restart.
In case the operating system hangs (stops, freezes, crashes), you can try a “warm boot” by pressing the
[Ctrl][Alt][Del] keys simultaneously. If this “warm boot” does not restart the Notebook PC, you can
reset the Notebook PC by using a “cold boot” which is switching the Notebook PC’s power OFF and
then back ON. Hold the power button until the Notebook PC shuts OFF (may take over 5 seconds).
NOTE: If neither of these methods work, you can press the reset button located in a
small hole on the bottom of the Notebook PC with a pen, mechanical pencil, or paper
clip. Do not use a standard pencil because the tip may break off in the hole.
Powering OFF the Notebook PC
For operating systems equipped with APM or ACPI (Windows 98/ME/2000), the Notebook PC can be
powered OFF by using Start | Shut Down... | Shut down. For operating systems without proper power
management (DOS, Windows NT), you must power OFF the Notebook PC by holding the power switch
for 2 seconds (as opposed to 1 second to power ON) after closing applications and exiting operating
systems. This is necessary in order to prevent accidental power-OFFs. It will take about 5 seconds to
power OFF the Notebook PC if you do it while the Notebook PC hangs and stopped responding,
28
Loading...
+ 64 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.