ASUS S82 User Manual
NOTEBOOK PC
USER’S MANUAL
Product Name: Notebook PC
Manual Revision: 1.02 E640
Release Date: October 2000
Safety Statements
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of a shielded-type power cord is required in order to meet FCC
emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded
cables to connect I/O devices to this equipment. You are cautioned that changes or
modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the
Federal Register, National Archives and Records Administration, U.S. Government Printing Office.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
For use with AC Adaptor Model ADP-45GB (Pour Utiliser Avec Modele ADP-45GB)
2
Safety Statements
Nordic Cautions (for Notebook PC with Lithium-Ion Battery)
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions. (English)
VORSICHT! Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben
oder einem vom Hersteller empfohlenem ähnlichen T yp. Entsorgung gebrauchter Batterien nach Angaben
des Herstellers. (German)
ADVARSELI! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. (Danish)
VARNING! Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. (Swedish)
VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu. V aihda paristo ainoastaan laitevalmistajan
sousittelemaan tyyppiin. Hävitä käytetty paristo valmistagan ohjeiden mukaisesti. (Finnish)
ATTENTION! Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer
uniquement avec une batterie du mêre type ou d’un type équivalent recommandé par le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du fabricant. (French)
ADVARSEL! Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en
tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens
instruksjoner. (Norwegian)
(Japanese)
Macrovision Corporation Product Notice
This product incorporates copyright protection technology that is protected by method claims of certain
U.S.A. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
3
CTR 21 Approval (for Notebook PC with built-in Modem)
Danish
Dutch
English
Finnish
4
French
German
Greek
Italian
Portuguese
Spanish
Swedish
CTR 21 Approval (for Notebook PC with built-in Modem)
5
Table of Contents
1. INTRODUCING THE NOTEBOOK PC 9
About This User’s Manual...................................................................................... 10
Notes For This Manual......................................................................................10
Caring Information ................................................................................................. 11
Transportation Precautions.................................................................................... 12
2. KNOWING THE PARTS 13
Top Side.................................................................................................................14
Front Side .............................................................................................................. 16
Left Side................................................................................................................. 17
Right Side .............................................................................................................. 18
Rear Side............................................................................................................... 19
3. GETTING STARTED 21
Installing and Removing the Battery Pack ............................................................. 22
Using the Battery Pack .......................................................................................... 24
Before using your Notebook PC on the road .................................................... 24
Battery Care...................................................................................................... 24
Operating Systems ................................................................................................ 24
Support Software .............................................................................................. 24
Power Connection ................................................................................................. 25
Powering ON The Notebook PC............................................................................ 26
The Power-On Self Test (POST) ...................................................................... 26
Save-to-Disk Partition ............................................................................................27
Restarting or Rebooting......................................................................................... 27
Powering OFF the Notebook PC ........................................................................... 27
LED Status Indicators ............................................................................................28
Using the Keyboard ............................................................................................... 29
Colored Hot Keys.............................................................................................. 29
Microsoft Windows™ Keys ............................................................................... 30
Keyboard as a Numeric Keypad ....................................................................... 30
Keyboard as Cursors ........................................................................................ 31
4. USING THE NOTEBOOK PC 33
Pointing Device...................................................................................................... 34
Using the Touchpad .......................................................................................... 34
Caring for the Touchpad ................................................................................... 37
Mouse or Keyboard Connection (Optional) ........................................................... 37
AiBox Portable Module Bay (Included) ..................................................................38
Laser Safety...................................................................................................... 38
CDRH Regulations ........................................................................................... 38
Using the CD-ROM Drive ................................................................................. 39
DVD-ROM Drive Information ............................................................................ 40
6
Table of Contents
Regional Playback Information ......................................................................... 41
Region Definitions............................................................................................. 41
Listening to Audio CD ....................................................................................... 42
External Display Connections (Optional) ............................................................... 43
External Audio Connections (Optional).................................................................. 43
PC Cards (PCMCIA) (Optional) ............................................................................. 44
32-bit CardBus & Zoomed Video Port .............................................................. 44
Inserting a PC Card (PCMCIA)......................................................................... 45
Removing a PC Card (PCMCIA) ...................................................................... 46
Universal Serial Bus .............................................................................................. 47
Driver Support................................................................................................... 47
USB Floppy Disk Drive (Optional) ......................................................................... 48
USB Port Replicator (Optional).............................................................................. 49
USB to Printer Cable (Optional)............................................................................. 50
Parallel Printer Compatibility List ...................................................................... 50
Vehicle/Air Power Adapter (Optional) .................................................................... 51
Features............................................................................................................ 51
Usage ............................................................................................................... 51
Modem and Network Connections......................................................................... 52
Modem Connection........................................................................................... 53
Network Connection ......................................................................................... 53
IR Wireless Communication .................................................................................. 54
Guidelines for using IR communication ............................................................54
Enabling Infrared .............................................................................................. 54
AC Power System.................................................................................................. 54
Battery Power System ........................................................................................... 54
Charging the Battery Pack................................................................................ 54
Using Battery Power ......................................................................................... 56
Power Management Modes................................................................................... 57
Full Power Mode & Maximum Performance .....................................................57
APM and ACPI.................................................................................................. 57
Suspend Mode.................................................................................................. 57
Standby Mode................................................................................................... 58
Power State Summary...................................................................................... 58
Thermal Power Control..................................................................................... 59
System Memory Expansion ................................................................................... 59
Processor Upgrades .............................................................................................. 59
Securing Your Notebook PC .................................................................................. 60
Other Security Products.................................................................................... 60
7
Table of Contents
5. CONFIGURING THE BIOS 61
Updating Your BIOS............................................................................................... 62
Creating a BIOS Update Floppy Disk ............................................................... 62
Copying BIOS Update Files to the Hard Disk Drive.......................................... 62
Updating BIOS with a Floppy Disk Drive .......................................................... 63
Updating BIOS From the Hard Disk Drive ........................................................ 63
BIOS Setup Program ............................................................................................. 64
BIOS Menu Bar................................................................................................. 65
BIOS Legend Bar.............................................................................................. 65
Main Menu .............................................................................................................67
Primary Master (sub-menu) ...................................................................................69
Primary Slave (sub-menu) .....................................................................................71
Advanced Menu..................................................................................................... 72
I/O Device Configuration (sub-menu) .................................................................... 74
Security Menu........................................................................................................ 76
Hard Disk Password: ........................................................................................ 77
Password Usage Summary ................................................................................... 77
The Power Menu ................................................................................................... 78
Boot Menu ............................................................................................................. 80
Exit Menu............................................................................................................... 81
APPENDIX 83
Internal Modem Compliancy .................................................................................. 84
Protocols and Compliancy ................................................................................ 84
Glossary................................................................................................................. 87
Index ...................................................................................................................... 91
Owner Information ................................................................................................. 94
8
1. INTRODUCING THE NOTEBOOK PC
About This User’s Manual
Caring Information
Transportation Precautions
9
1. Introducing the Notebook PC
About This User’s Manual
You are reading the Notebook PC User’s Manual. This User’s Manual provides information on the
various components in the Notebook PC and how to use them. The following are major sections of this
User’s Manuals:
1. Introducing the Notebook PC
Introduces you to the Notebook PC and this User’s Manual.
2. Knowing the Parts
Gives you information on the Notebook PC’s components.
3. Getting Started
Gives you information on getting started with the Notebook PC.
4. Using the Notebook PC
Gives you information on using the Notebook PC’s components.
5. Configuring the BIOS
Gives you information on configuring the BIOS software.
6. Appendix
Introduces you to optional accessories and gives additional information.
Notes For This Manual
This User’s Manual was created using Macintosh versions of Adobe® PageMaker™ 6.52, Adobe
Photoshop™ 5.5, Adobe® Illustrator® 8.0, and Macromedia® Freehand™ 8.0.1. The body text type used
in this manual is “Times” (MAC) or “Times New Roman” (Windows™) and headings are “Helvetica”
(MAC) or “Arial” (Windows™). A few notes and warnings in bold are used throughout this guide that
you should be aware of in order to complete certain tasks safely and completely. These notes have
different degrees of importance as described below:
WARNING! Information to prevent
damage to components, damage to
data, or personal injury.
CAUTION! Information on actions that
must be avoided to prevent damage to
components, damage to data, or personal injury.
T ext enclosed in < > or [ ] represents a key on the keyboard; do not actually type the <
> or [ ] and the enclosed letters.
TIP: Tips and useful information for
power (advanced) computer users.
NOTE: Tips and information to aid in
completing a task.
®
10
1. Introducing the Notebook PC
Caring Information
WARNING! The following safety precautions will increase the life of the Notebook PC.
Follow all precautions and instructions. Except as described in this manual, refer all
servicing to qualified personnel. Do not use damaged power cords, accessories, or
other peripherals. Do not use strong solvents such as thinners, benzene, or other
chemicals on or near the surface.
Disconnect the AC power and remove the battery pack(s) before cleaning. Wipe the Notebook PC using
a clean cellulose sponge or chamois cloth dampened with a solution of nonabrasive detergent and a few
drops of warm water and remove any extra moisture with a dry cloth.
DO NOT place on uneven or unstable work
surfaces. Seek servicing if the casing has
been damaged.
DO NOT expose to
strong magnetic or
electrical fields.
WARNING! Do not leave the base of your Notebook PC on your lap or any part of your
body for an extended period in order to prevent discomfort or injury from heat exposure.
DO NOT place or drop
objects on top and do
not shove any foreign
objects into the Notebook PC.
DO NOT expose to extreme temperatures (below
0˚C (32˚F) or above 50˚C (122˚F)) or to direct sunlight. Do not block the fan vents! DO NOT throw
batteries in fires as they may explode. Check local
codes for special battery disposal instructions.
DO NOT expose to or
use near liquids, rain, or
moisture. DO NOT use
the modem during an
electrical storm.
DO NOT expose to
dirty or dusty environments. DO NOT operate during a gas leak.
DO NOT press or touch
the display panel. Do not
place together with small
items that may scratch or
enter the Notebook PC.
11
1. Introducing the Notebook PC
Transportation Precautions
T o prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is
turned OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not
transport the Notebook PC while the power is still ON. Close the display panel and check that it is
latched securely in the closed position to protect the keyboard and display panel.
Remove Floppy Disks
Make sure that the 1.44MB floppy disk drive does not contain a diskette when transporting the external
USB floppy disk drive. When a diskette is inserted into the floppy disk drive, the eject button protrudes
out. If you attempt to transport the floppy disk drive with a diskette in the drive, you risk damaging the
eject button and also risk scratching the surface of the diskette when the floppy disk drive is jolted.
Cover Your Notebook PC
Use a carrying case such as the one supplied with your Notebook PC to protect it from dirt, water,
shock, and scratches.
Charge Your Batteries
If you intend to use battery power, be sure to fully charge your battery pack and any optional battery
packs before going on long trips. Remember that the power adapter charges the battery pack as long as
it is plugged into the computer and an AC power source. Be aware that it takes much longer to charge
the battery pack when the Notebook PC is in use.
Travelling Precautions
Contact your airline if you want to use the Notebook PC on the airplane. Most airlines will have restrictions for using electronic devices. Most airlines will allow electronic use only between and not during
takeoffs and landings.
CAUTION! There are three main types of airport security devices: X-ray machines
(used on items placed on conveyor belts), magnetic detectors (used on people walking through security checks), and magnetic wands (hand-held devices used on people
or individual items). Y ou can send your Notebook PC and diskettes through airport Xray machines. However, it is recommended that you do not send your Notebook PC or
diskettes through airport magnetic detectors or expose them to magnetic wands.
NOTE: The surface glaze is easily dulled if not properly cared for . Be careful not to rub
or scrap the Notebook PC surfaces when transporting your Notebook PC.
12
2. KNOWING THE PARTS
Top Side
Front Side
Left Side
Right Side
Rear Side
13
2. Knowing the Parts
Top Side
Refer to the diagram below to identify the components on the top side of the Notebook PC.
Display Panel
Latch
Display Panel
Power
Switch &
Status LEDs
Microphone
Speaker (on bottom)
Air Vent
Air Vent
Keyboard
Touchpad
Touchpad
Buttons
Opening the Display Panel
One spring-loaded latch on the front of the Notebook PC locks the display panel in the closed position
when the Notebook PC is not in use. To open the display panel, push the button inwards with your thumb
and lift up on the display panel at the same time. This design allows a single hand to be used when opening
the display panel. Slowly tilt the display panel forward or backward to a comfortable viewing angle.
WARNING! When opening, do not force the display panel down to the table or else the
hinges may break! Never lift the Notebook PC by the display panel!
Display Panel Care
The LCD screen is very delicate and requires careful handling. Pay attention to the following precautions:
• When not in use, keep the display panel closed to prevent dust accumulation.
• Do not use chemical cleaners on the screen. Wipe only with a dry cloth or tissue.
• Do not put your fingers or any objects directly on the screen.
• Do not press or lay any objects on the machine when it is closed.
• Do not carry the Notebook PC with small or sharp objects (e.g. paper clips or staples) that may enter
the Notebook PC and scratch the display panel.
14
2. Knowing the Parts
The following describes the components of the Notebook PC as viewed from the top as shown by the
illustration on the previous page.
Display Panel
The display panel functions the same as a desktop monitor. The Notebook PC uses a 1024x768 or
800x600 12.1” active matrix TFT LCD, which provides excellent viewing like that of desktop monitors. Unlike desktop monitors, the LCD panel does not produce any radiation or flickering, so it is
easier on the eyes.
NOTE: By default, closing the display panel turns OFF the display to conserve power .
Opening the display panel turns the display back ON. You can change the display
panel settings in the Advanced Power Management in Windows.
Power Switch
The power switch allows powering ON and OFF the Notebook PC. Push the switch once to turn ON
and once to turn OFF the Notebook PC. To prevent accidental turning OFF of the power, it is designed
to take longer (about 4 seconds) to turn OFF than to turn ON the power.
Status LEDs (top)
The Notebook PC has status LEDs above the keyboard to display storage device access, number lock,
and capital lock statuses. Details are described later in this manual.
Microphone
The built-in microphone provides a source for general note taking, voicemail recording, or for use with
Internet phone software. See “Front Side” for external microphone connection.
Air Vent
The air vents allow fresh air to be used to circulate warm air out of the Notebook PC. Be careful not to
block the air vents!
Keyboard
The keyboard provides full-sized 19mm keys with 2.3mm travel and palm rest. Two Windows™ function keys are provided to help ease navigation in the Windows™ operating system.
Touchpad and Buttons
The touchpad with its four buttons is a pointing device that provides the same functions as a desktop
mouse with scrolling capability. Scrolling allows you to move up or down in a document or web page
without having to click on the scroll bars.
Speaker
The single built-in speakers allow you to hear left and right channel audio without additional attachments. The multimedia sound system features an integrated digital audio controller that produces rich,
vibrant sound in high quality 16-bit stereo. With a pair of integrated stereo speakers, a built-in microphone, and both input and output audio jacks for external audio devices, the Notebook PC fulfills most
multimedia computing needs. All audio features are software controlled.
15
2. Knowing the Parts
Front Side
Refer to the diagram below to identify the components on the front side of the Notebook PC.
296mm
26mm
Display Panel
Release Button
The following describes the front components of the Notebook PC as shown by the picture above.
Display Panel Release Button
One display panel latch is used to lock the display panel in the closed position. To open the display
panel, push the button inwards with your thumb and lift up on the display panel at the same time.
Headphone (Jack)
The stereo headphone jack is used to connect the Notebook PC’s audio out signal to amplified speakers
or headphones. Using this jack automatically disables the built-in speakers.
Mic In (Microphone Jack)
The mono microphone jack can be used to connect an external microphone or output signals from audio
devices. Using this jack automatically disables the built-in microphone.
Power Indicator
The green LED lights to indicate that the Notebook PC is turned ON and blink when the Notebook PC
is in the Suspend mode. This LED is OFF when the Notebook PC is in the Suspend mode.
Charge Indicator
Indicates that the battery is being charged when ON and fully charged when OFF. This LED only lights
when the power adapter is used. This LED does not light up if there is no installed battery. Slow flash
means the battery power is low and requires charging. Quick flashing means that the battery pack
cannot be charged and needs a replacement.
Email Indicator
Flashes when there is one or more new email(s) in your email program’s inbox. This function requires
software setup and may not be currently configured on your Notebook PC. This function is designed for
Microsoft email software only and may not work with email software from other companies.
16
2. Knowing the Parts
Left Side
Refer to the diagram below to identify the components on the left side of the Notebook PC.
230mm
DC Power
Input Jack
The following describes the components on the left side of the Notebook PC as shown by the illustration above.
DC IN
DC Power Input Jack
The supplied power adapter converts AC power to DC power for use with this jack. Power supplied
through this jack supplies power to the Notebook PC and charges the internal battery pack.
Hard Disk
Drive (in tray)
Hard Disk Drive
The hard disk drive is mounted in a removable tray. This tray is secured by a large black screw at the
bottom of the Notebook PC. The removable tray allows easy hard disk drive swapping or upgrade.
17
2. Knowing the Parts
Right Side
Refer to the diagram below to identify the components on the right side of the Notebook PC.
230mm
PC Card
(PCMCIA) Eject
PC Card
(PCMCIA) Sockets
Fast Infrared Port
Cooling Fan/
Air Vent
The following describes the components on the right side of the Notebook PC as shown by the illustration above.
PC Card (PCMCIA) Sockets and Eject
T wo PCMCIA 2.1 compliant sockets for two Type I or Type II or one T ype III PC card are available. The
upper socket includes support for 32-bit CardBus and Zoomed Video. This allows accommodation of all
Notebook PC expansion options such as memory cards, fax/modems, SCSI adapters, high-speed network
adapters, and video capture/conference cards. The two eject buttons allow easy ejection of the PC cards.
Fast Infrared Port
The fast infrared (IrDA) communication port allows convenient wireless data communication with
infrared-equipped devices or computers up to 4Mbits/sec. This allows easy wireless synchronization
with PDAs or mobile phones and even wireless printing to printers. If your office supports IrDA networking, you can have wireless connection to a network anywhere provided there is a direct line of
sight to an IrDA node. Small of fices can use IrDA technology to share a printer between several closely
placed Notebook PCs and even send files to each other without a network.
Cooling Fan
The cooling fan turns ON when the temperature rises past a set threshold. The cooling fan is an extra
feature needed for upgrading to faster processors in the future. The top screen allows cool air to enter
the Notebook PC. Do not block the area above the keyboard!
18
2. Knowing the Parts
Rear Side
Refer to the diagram below to identify the components on the rear side of the Notebook PC.
296mm
26mm
K
Air Vent
Kensington
Lock Port
The following describes the components on the rear side of the Notebook PC as shown by the illustration above.
®
AiBox
I/O Port
External
Monitor
Port
LAN
Port
(RJ-45)
Modem
Port
(RJ-1 1)
2 USB
Ports
Kensington® Lock Port
K
The Kensington® lock port allows the Notebook PC to be secured using Kensington® compatible Notebook PC security products. These security products usually include a metal cable and lock that prevent
the Notebook PC to be removed from a fixed object. Some security products may also include a motion
detector to sound an alarm when moved.
AiBox I/O Port
The AiBox I/O port is an expansion bus for connection to an AiBox Portable Module Bay. AiBox and
module devices are explained later in this user’s manual.
LAN Port
The RJ-45 LAN port supports an RJ-45 Ethernet cable. The internal LAN supports 10Base-T or 100BaseTX standard or duplex networks.
Modem Port
The RJ-11 telephone port supports an RJ-11 telephone cable. The internal modem supports up to 56K
V.90 transfers.
WARNING! The built-in modem does not support the voltage used in digital phone
systems. Do not connect the modem port to a digital phone system or else damage
will occur to the Notebook PC.
19
2. Knowing the Parts
External Monitor Port
The 15-pin D-sub monitor port supports a standard VGA-compatible device such as a monitor or projector to allow viewing on a larger external display . An external monitor can also be used for dual-view
or dual-application support to allow referencing data on one display while working on the other display. This feature can really increase your productivity!
USB Port
Universal Serial Bus (USB) supports many USB compatible devices such as keyboards, pointing devices, video cameras, modems, hard disk drives, printers, monitors, and scanners connected in a series
up to 12Mbits/sec. In order to connect more USB devices, you can purchase the optional USB Port
Replicator. USB supports hot-swapping of devices so that peripherals can be connected or disconnected while the Notebook PC is ON.
20
3. GETTING STARTED
Installing/Removing Battery Pack
Using the Battery Pack
Operating Systems
Power Connection
Powering ON The Notebook PC
Save-to-Disk Partition
Restarting or Rebooting
Powering OFF The Notebook PC
LED Status Indicators
Using the Keyboard
21
3. Getting Started
Installing and Removing the Battery Pack
Your Notebook PC may or may not have its battery pack installed. If your Notebook PC does not have
its battery pack installed, there will be a large opening at the bottom of the Notebook PC. Use the
following procedures to install or remove the battery pack.
To install a battery pack:
1. Insert the battery pack with the connector side
over the connectors in the battery compartment
as indicated by the arrow.
2. Slide the battery latch towards the lock icon
as indicated by the arrow to lock the battery
pack in place.
22
WARNING! Only use battery packs and power adapters supplied with this Notebook
PC or specifically approved by the manufacturer or retailer for use with this model.
To remove the battery pack:
3. Getting Started
1. Slide the battery latch towards the unlock icon
as indicated by the arrow to unlock the battery
pack.
2. Lift the battery out by the edge close to the
battery latch as indicated by the arrow.
WARNING! Never attempt to remove the battery pack while the Notebook PC is turned
ON, as this may result in the loss of working data.
23
3. Getting Started
Using the Battery Pack
Before using your Notebook PC on the road
Before you use your Notebook PC on the road, you will have to charge the battery pack. The battery
pack begins to charge as soon as the Notebook PC is connected to external power. Fully charge the
battery pack before using it for the first time. A new battery pack must completely charge before the
Notebook PC is disconnected from external power. The battery pack is fully charged when the battery
charge light turns OFF. It takes about 2 hours to fully charge the battery when the Notebook PC is
turned OFF and about 4 hours when the Notebook PC is turned ON.
Battery Care
The Li-Ion battery pack has no “Memory Effect” (officially called “Voltage Depressor”) but like all
rechargeable batteries, the number of charges is limited. Fully draining and charging the battery once a
day every day will last over a year but how long beyond that will depend on your environment temperature and humidity. Make sure that the battery is used in a temperature range between 10˚C and 29˚C
(50˚F and 85˚F), taking into account that the Notebook PC’s internal temperature is higher than the
outside. Any temperatures above or below this range will shorten the life of the battery. But in any case,
the battery’s usage time will eventually be too short to use and a new one must be purchased.
Operating Systems
This Notebook PC offers its customers the choice of a pre-installed operating system such as Microsoft
Windows 98, Windows ME (Millennium), or Windows 2000. The choices and languages will depend
on territory.
Support Software
This Notebook PC comes with a support CD that provides BIOS, drivers and applications to enable
hardware features, extend functionality , help manage your Notebook PC, or add functionality not provided by the native operating system. If updates or replacement of the support CD is necessary , contact
your dealer for web sites to download individual software drivers and utilities.
The support CD contains all drivers, utilities and software for all popular operating systems including
those that have been pre-installed. The support CD does not include the operating system itself. The
support CD is necessary even if your Notebook PC came pre-configured in order to provide additional
software not included as part of the factory pre-install.
A recovery CD is optional and includes an image of all the drivers and utilities included on the factory
installed hard drive as well as the operating system itself. The recovery CD provides a comprehensive
recovery solution that quickly restores the Notebook PC’s operating system and software to its original
working state provided that your hard disk drive is in good working order. Contact your retailer if you
require such a solution.
24
3. Getting Started
Power Connection
Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the
power cord to any 110V-120V as well as 220V-240V outlets without setting switches or using power
converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a dif ferent standard. Most hotels will provide universal outlets to support differ ent power cords as well as voltages. It is always best to ask an experienced traveler about AC outlet
voltages when bringing power adapters to another country.
TIP: You can buy travel kits for the Notebook PC that includes power and modem
adapters for almost every country.
With the AC power cord connected to the AC-DC converter , connect the AC power cord to an AC outlet
(preferably with surge-protection) and then connect the DC plug to the Notebook PC. Connecting the
AC-DC adapter to the AC outlet first allows you to test the AC outlet’s power and the AC-DC converter
itself for compatibility problems before connecting the DC power to the Notebook PC. The green
power LED on the adapter lights up if the power is within accepted ranges.
WARNING! Damage may occur if you use a different adapter to power the Notebook
PC or use the Notebook PC’s adapter to power other electrical devices. If there is
smoke, burning scent, or extreme heat coming from the AC-DC adapter, seek servicing. Seek servicing if you suspect a faulty AC-DC adapter . You may damage both your
battery pack(s) and the Notebook PC with a faulty AC-DC adapter.
NOTE: This Notebook PC may come with either a two or three-prong plug depending
on territory. If a three-prong plug is provided, you must use a grounded AC outlet or
use a properly grounded adapter to ensure safe operation of the Notebook PC.
AC-DC
Converter
Connect this end of the
power cord to the
AC-DC converter
DC Power Plug
Plug the “AC Power Cord”
into an electrical outlet
25
3. Getting Started
Powering ON The Notebook PC
The Notebook PC’s power -ON message appears on the screen followed by a short beep when you turn
it ON. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS
Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. If you
press the [Esc] button during the splash screen, standard boot information such as the BIOS version can
be seen. You will also be presented with a boot menu that allows you to select bootup from “Removable
Devices”, “Hard Drive”, “A TAPI CD-ROM Drive”, or enter BIOS setup. Use the up and down cursors
to make your selection and press [Enter] to execute.
WARNING! Never turn OFF or reset your Notebook PC while the hard disk or floppy
disk is in use and the activity LED is lit; doing so can result in loss or destruction of
your data. To protect the hard disk drive, always wait at least 5 seconds after turning
OFF your Notebook PC before turning it back ON.
NOTE: Before bootup, the display panel flashes when the power is turned ON. This is
part of the Notebook PC’s test routine and is not a problem with the display.
The Power-On Self Test (POST)
When you turn ON the Notebook PC, it will first run through a series of software-controlled diagnostic
tests called the Power-On Self Test (POST). The software that controls the POST is installed as a
permanent part of the Notebook PC’s architecture. The POST includes a record of the Notebook PC’s
hardware configuration, which is used to make a diagnostic check of the system. This record is created
by using the BIOS Setup program. If the POST discovers a difference between the record and the
existing hardware, it will display a message on the screen prompting you to correct the conflict by
running BIOS Setup. In most cases the record should be correct when you receive the Notebook PC.
When the test is finished, you may get a message reporting “No operating system found” if the hard
disk was not pre-loaded with an operating system. This indicates that the hard disk is correctly detected
and ready for the installation of a new operating system.
The S.M.A.R.T. (Self Monitoring and Reporting Technology) checks the hard disk drive during POST
and gives a warning message if the hard disk drive requires servicing. If any critical hard disk drive
warning is given during bootup, backup your data immediately and run W indows disk checking program.
T o run Window’s disk checking program: (1) right-click any hard disk drive icon in “My Computer”, (2)
choose Properties, (3) click the Tools tab, (4) click Check Now, (5) select a hard disk drive, (6) select
Thorough to also check for physical damages, and (7) click Start. Third party disk utilities such as Symantec’s
Norton Disk Doctor can also perform the same functions but with greater ease and more features.
WARNING! If warnings are still given during bootup after running a software disk
checking utility, you should take your Notebook PC in for servicing. Continued use
may result in data loss.
26
3. Getting Started
Save-to-Disk Partition
The Notebook PC supports Advanced Power Management to save battery power and extend its working time. One type of power management is “Save-to-Disk.” Save-to-Disk is a suspend mode where
your operating system and application data is saved to a separate partition and retrieved when the
Notebook PC comes out of suspend mode. A partition is a space on the hard disk drive equivalent to
having a second hard disk drive. If you would like the Notebook PC to support the Save-to-Disk mode,
run the PHDISK.EXE utility to setup a Save-to-Disk partition on your hard disk. The Save-to-Disk
partition must be larger than the total system memory of the Notebook PC. T o check whether a Save-toDisk partition exist on your hard drive, run FDISK.EXE located in Windows’ command directory or
Windows rescue floppy disk. You can also compare your working partition’s size with the hard drive’s
size as shown in BIOS setup. See the Drivers and Utilities Support CD User’s Manual for detailed
usage instructions.
WARNING! All other partitions and their data will be cleared by the PHDISK.EXE utility. This must be done BEFORE you install an operating system onto your hard disk.
The included hard disk drive comes with the Save-to-Disk partition pre-configured
from the factory.
Restarting or Rebooting
After installing drivers (please see the “Drivers and Utilities Guide”), installing applications, or making configuration changes, you may be prompted to restart the system to update the operating system
and complete the installation process. To restart the system, press the [Ctrl][Alt][Del] keys simultaneously. This is known as a “warm boot.” If this “warm boot” does not restart the Notebook PC, you
can reset the Notebook PC by using a “cold boot” which is switching the Notebook PC’s power OFF
and then back ON. Remember to wait 5 seconds before switching the Notebook PC back ON.
NOTE: If neither of these methods work, you can press the reset button located in a
small hole on the bottom of the Notebook PC with a pen or paper clip. Do not use a
pencil because the tip may break off in the hole.
Powering OFF the Notebook PC
For operating systems equipped with APM or ACPI (Windows 98/2000), the Notebook PC can be
powered OFF by using Start | Shut Down... | Shut down. For operating systems without proper power
management (DOS, Windows NT), you must power OFF the Notebook PC by holding the power switch
for 2 seconds (as opposed to 1 second to power ON) after closing applications and exiting operating
systems. This is necessary in order to prevent accidental power-OFFs. It will take 4 to 5 seconds to
power OFF the Notebook PC if you do it while the Notebook PC hangs and stopped responding,
27
3. Getting Started
LED Status Indicators
There are several LED status indicators on the Notebook PC. The LED status indicators give information on the Notebook PC’s current operating and keyboard statuses. The following illustration shows
the meaning of each status LED.
Above Keyboard
Programmable
Instant Key 2
1 A
Capital Lock
Number Lock
Activity Indicator
The following gives a description for each of the LED status indicators.
Email Instant Key
Programmable
Instant Key 1
Internet Instant Key
Notebook PC Front
Email
Indicator
Charge Indicator
Power Indicator
Activity Indicator
Indicates that the Notebook PC is accessing the floppy, hard disk, CD/DVD-ROM drive. The light
flashes proportional to the access time.
Number Lock
1
Indicates that number lock [Num Lk] is activated when lighted. Number lock allows some of the keyboard letters to act as numbers for easier numeric data input.
Capital Lock
A
Indicates that capital lock [Caps Lock] is activated when lighted. Capital lock allows some of the
keyboard letters to type using capitalized letters (e.g. A, B, C). When the capital lock light is OFF, the
typed letters will be in the lower case form (e.g. a,b,c).
Charge Indicator
Indicates that the battery is being charged when ON and fully charged when OFF. This LED only lights
when the power adapter is used. This LED does not light up if there is no installed battery. Slow flash
means the battery power is low and require charging. Quick flashing means that the battery pack cannot
be charged and needs a replacement.
Power Indicator
The green LED lights to indicate that the Notebook PC is turned ON and blink when the Notebook PC
is in the Save-To-RAM mode. This LED is OFF when the Notebook PC is in the Save-To-Disk mode.
28
3. Getting Started
Using the Keyboard
Colored Hot Keys
The following defines the colored hot keys on the Notebook PC’s keyboard. The colored commands can only
be accessed by first pressing and holding the function key while pressing a key with a colored command.
Fn
Suspend: Places the Notebook PC in suspend mode (either Save-to-RAM or Save-toDisk depending on BIOS setup). This is not the same as “stand by” in MS Windows.
Fn
Open Sun: Increases the display brightness. If the display appears too dark, use
this command.
Fn
Solid Sun: Decreases the display brightness. If the display appears to bright, use
this command.
Fn
Fn
Fn
F7
LCO
F8
LCO
F9
LCD: Toggles the display panel ON and OFF. This is a quick way to hide your
work.
LCD/Monitor Icons: T oggles between the Notebook PC’s LCD display and an ex-
ternal monitor in this series: Notebook PC LCD -> External Monitor -> Both
Speaker Icons: Toggles the speakers ON and OFF. This allows you to quickly mute
the volume.
Fn
Fn
Speaker Up Icon: Toggles the volume increase in Windows Volume Control. This
function electronically raises the audio ouput signal.
Speaker Down Icon: Toggles the volume decrease in Windows Volume Control.
This function electronically lowers the audio ouput.
Fn
Fn
Num Lk: Toggles the numeric keypad (number lock) ON and OFF. Allows you to
use a larger portion of the keyboard for number entering.
Scr Lk: T oggles the “Scroll Lock” ON and OFF . Allows you to use a lar ger portion
of the keyboard for cell navigation.
NOTE: Hot Keys work only on the Notebook PC’s own keyboard and not on any externally connected keyboards.
29
3. Getting Started
Microsoft Windows™ Keys
There are two special Windows™ keys on the keyboard as described below.
The key with the Windows™ Logo activates the Start menu located at the bottom left of the
Windows™ desktop.
The other key , that looks like a Windows™ menu with a small cursor, activates the proper-
ties menu and is equivalent to pressing the right mouse button on a Windows™ object.
Keyboard as a Numeric Keypad
The numeric keypad is embedded in the keyboard and consists of 15 keys that make number intensive
input more convenient. These dual-purpose keys are labeled in orange on the key caps. Numeric assignments are located at the upper right hand corner of each key as shown in the figure. When the
Fn
numeric keypad is engaged by pressing
, the number lock LED lights up. If an external key-
board is connected, pressing the
keyboards simultaneously. To disable the numeric keypad while keeping the keypad on an external
keyboard activated, press the Fn keys on the Notebook PC.
on the external keyboard enables/disables the NumLock on both
30
Loading...