Asus J1800I-C User Manual

J1800I-C

Motherboard

E9068
First Edition

February 2014

Copyright © 2014 ASUSTeK COMPUTER INC. All Rights Reserved.

No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.

Offer to Provide Source Code of Certain Software

This product contains copyrighted software that is licensed under the General Public License (“GPL”),
under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the
applicable law. Copies of these licenses are included in this product.

Where the applicable license entitles you to the source code of such software and/or other additional data,
you may obtain it for a period of three years after our last shipment of the product, either

(1) for free by downloading it from http://support.asus.com/download
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location

where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan

In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.

The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.

This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source

Software licenses. If however you encounter any problems in obtaining the full corresponding source
code we would be much obliged if you give us a notication to the email address [e-mail], stating
the product and describing the problem (please DO NOT send large attachments such as source code
archives, etc. to this email address).

ii

Contents

Safety information ...................................................................................................... iv

About this guide ......................................................................................................... iv

Package contents ....................................................................................................... vi

J1800I-C specications summary ............................................................................ vi

Chapter 1: Product introduction

1.1 Before you proceed ...................................................................................... 1-1

1.2 Motherboard overview .................................................................................

1.3 Central Processing Unit (CPU) ....................................................................

1.4 System memory ............................................................................................

1.5 Expansion slots ............................................................................................

1.6 Jumpers

1.7 Connectors ....................................................................................................

1.8 Software support ........................................................................................

Chapter 2: BIOS information

2.1 Managing and updating your BIOS .............................................................2-1

2.2 BIOS setup program .....................................................................................

2.3 My Favorites

2.4 Main menu ...................................................................................................

2.5 Advanced menu ..........................................................................................

2.6 Monitor menu ..............................................................................................

2.7 Boot menu ...................................................................................................

2.8 Tools menu ..................................................................................................

2.9 Exit menu ....................................................................................................

.........................................................................................................1-7

1-16

.................................................................................................. 2-9

2-10

2-12

2-18

2-21

2-26

2-27

1-2

1-4

1-4

1-6

1-9

2-6

Appendices

Notices ..................................................................................................................... A-1

ASUS contact information ...................................................................................... A-4

iii

Safety information

Electrical safety

To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

•
before relocating the system.

When adding or removing devices to or from the system, ensure that the power cables

•
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.

Before connecting or removing signal cables from the motherboard, ensure that all

•
power cables are unplugged.

Seek professional assistance before using an adapter or extension cord. These devices

•
could interrupt the grounding circuit.

Ensure that your power supply is set to the correct voltage in your area. If you are not

•
sure about the voltage of the electrical outlet you are using, contact your local power
company.

If the power supply is broken, do not try to x it by yourself. Contact a qualied service

•
technician or your retailer.

Operation safety

Before installing the motherboard and adding devices on it, carefully read all the manuals

•
that came with the package.

Before using the product, ensure all cables are correctly connected and the power

•
cables are not damaged. If you detect any damage, contact your dealer immediately.

To avoid short circuits, keep paper clips, screws, and staples away from connectors,

•
slots, sockets and circuitry.

Avoid dust, humidity, and temperature extremes. Do not place the product in any area

•
where it may become wet.

Place the product on a stable surface.

•

If you encounter technical problems with the product, contact a qualied service

•
technician or your retailer.

About this guide

This user guide contains the information you need when installing and conguring the

motherboard.

How this guide is organized

This guide contains the following parts:

• Chapter 1: Product introduction

This chapter describes the features of the motherboard and the new technology it
supports.

• Chapter 2: BIOS information

This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.

iv

Where to nd more information

Refer to the following sources for additional information and for product and software
updates.

1. ASUS websites

The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.

2. Optional documentation

Your product package may include optional documentation, such as warranty yers,

that may have been added by your dealer. These documents are not part of the
standard package.

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.

CAUTION: Information to prevent damage to the components when trying to
complete a task

IMPORTANT: Instructions that you MUST follow to complete a task. .

NOTE: Tips and additional information to help you complete a task.

Typography

Bold text Indicates a menu or an item to select.

Italics

<Key> Keys enclosed in the less-than and greater-than sign

<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key

Used to emphasize a word or a phrase.

means that you must press the enclosed key.

Example: <Enter> means that you must press the Enter or
Return key.

names are linked with a plus sign (+).

v

Package contents

Check your motherboard package for the following items.

Motherboard ASUS J1800I-C motherboard

Cables 2 x Serial ATA 3.0 Gb/s cables

Accessories 1 x I/O Shields

Application DVD Support DVD

Documentation User Guide

If any of the above items is damaged or missing, contact your retailer.

J1800I-C specications summary

CPU Intel® Celeron® Dual-core Processor J1800

Memory 2 x SO-DIMM DDR3L 1333 MHz, Max 8GB, non-ECC, un-buffered memory

Dual-channel memory architecture

* Hyper DIMM support is subject to the physical characteristics of individual

CPUs. Please refer to Memory QVL for details.

** Refer to

www.asus.com for the latest Memory QVL (Qualied Vendors List).

Graphics Integrated Graphics Processor- Intel® HD Graphics support

Multi-VGA output support: HDMI, D-Sub port

- Supports HDMI with max. resolution of 1920x1080@60Hz

- Supports D-sub with max. resolution of 2560x1600@60Hz

- Maximum shared memory of 512MB

* With DX11, OCL 1.2, OGL ES Halti/2.0/1.1, OGL 3.2 support
** Support H.264, MPEG2, MVC, VC-1, WMV9 and VP8 decode acceleration

Expansion slots 1 x PCI Express x1 slot

Storage

LAN

Audio Realtek® ALC887 8-channel High Denition Audio CODEC

USB 1 x USB 3.0/2.0 ports at back panel (blue)

ASUS Unique
Features

1 x Mini PCI Express slot

2 x SATA 3.0Gb/s connectors

Realtek® 8111G PCIe Gigabit LAN controller

- Supports Jack-Detection, and Front Panel Jack-Retasking

• Use a chassis with HD audio module in the front panel to support an
8-channel audio output.

6 x USB 2.0/1.0 ports (2 at mid-board, 4 at back panel)

ASUS Exclusive Features

- ASUS Anti-surge Protection

- ASUS AI Suite 3

- ASUS USB 3.0 Boost

- ASUS Network iControl

ASUS Quiet Thermal Solution

- ASUS Fan Xpert

(continued on the next page)

vi

J1800I-C specications summary

ASUS Unique
Features

ASUS EZ DIY

- ASUS UEFI BIOS

- ASUS MyLogo 2

- ASUS EZ-FLash 2

- ASUS Crash Free BIOS3

100% All High-quality Conductive Polymer Capacitors

Back Panel I/O Ports 1 x PS/2 mouse/keyboard combo port

1 x HDMI port

1 x D-Sub port

1 x COM port

1 x USB 3.0/2.0 ports

4 x USB 2.0/1.1 ports

1 x Gigabit LAN (RJ-45) port

3 x Audio jacks support 8-channel audio output

Internal I/O
Connectors

BIOS features 64Mb Flash ROM, UEFI AMI BIOS, PnP, DMI2.0, WfM2.0,SM BIOS 2.7,

Manageability

Support DVD Drivers

Form factor

1 x USB 2.0/1.1 connectors support additional 2 USB 2.0/1.1 ports

2 x SATA 3.0Gb/s connectors

1 x Chassis fan connector

1 x CPU fan connector

1 x Front panel audio connector

1 x COM connector

1 x LPT connector

1 x TPM connector

1 x 24-pin EATX power connector

1 x 4-pin EATX 12V power connector

1 x Buzzer

1 x System panel connector

ACPI 2.0a, Multi-language BIOS, ASUS EZ Flash 2, ASUS CrashFree

BIOS 3, My Favorites, Quick Note, Last Modied log, F12 PrintScreen,

F3 Shortcut functions and ASUS DRAM SPD (Serial Presence Detect)
memory information

Wfm 2.0, DMI 2.0, WOL by PME, PXE

ASUS utilities

EZ Update

Anti-virus software (OEM version)

Mini ITX Form Factor, 6.7” x 6.7” (17cm x 17cm)

Specications are subject to change without notice.

vii

viii

Product introduction

1

1.1 Before you proceed

Take note of the following precautions before you install motherboard components or change
any motherboard settings.

• Unplug the power cord from the wall socket before touching any component.

• Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due
to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.

• Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so
may cause severe damage to the motherboard, peripherals, or components.

ASUS J1800I-C

1-1

J1800I-C

1.2 Motherboard overview

Before you install the motherboard, study the conguration of your chassis to ensure that the
motherboard ts into it.

Ensure that you unplug the power cord before installing or removing the motherboard.
Failure to do so can cause you physical injury and damage motherboard components.

1.2.1 Placement direction

When installing the motherboard, ensure that you place it into the chassis in the correct
orientation. The edge with external ports goes to the rear part of the chassis as indicated in
the image below.

1.2.2 Screw holes

Place four screws into the holes indicated by circles to secure the motherboard to the
chassis.

Do not overtighten the screws! Doing so can damage the motherboard.

Place this side towards

the rear of the chassis

1-2

Chapter 1: Product introduction

1.2.3 Motherboard layout

J1800I-C

ATX12V

ALC
887

AAFP

Super

I/O

CLRTC

USBPWB

USBPWF

KBPWR

17.0cm(6.7in)

17.0cm(6.7in)

DDR3_DIMM_A1 (64bit, 204-pin module)

CHA_FAN

CPU_FAN

DDR3_DIMM_B1 (64bit, 204-pin module)

LAN_USB_E12

KBMS_USB_E34

USB3_1

AUDIO

HDMI

F_PANEL

BUZZER

USB_23

SATA3G_1

SATA3G_2

COM1

APU

PCIEX1_1

RTL

8111G

VGA

COM2

Mini PCIe

LPT

BATTERY

TPM

EATXPWR

621

7

5

10 9

1

12

11

8

543

6

13

14

15

1.2.4 Layout contents

Connectors/Jumpers/Slots/LED Page

1. CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN) 1-13

2. Keyboard power (3-pin KBWR) 1-8

3. LPT connector (26-1 pin LPT) 1-12

4. COM port connector (10-1 pin COM1) 1-11

10. TPM connector (20-1 pin TPM) 1-14

11. Front panel audio connector (10-1 pin AAFP) 1-11

12. Intel® Celeron Dual-core Processor J1800 1-4

13. USB 2.0 connector (10-1 pin USB_23) 1-13

14. USB device wake-up (3-pin USBPWF) 1-8

15. USB device wake-up (3-pin USBPWB) 1-8

ASUS J1800I-C

5. DDR3 SO-DIMM sockets 1-4

6. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) 1-12

7. Serial ATA 3.0Gb/s connectors (7-pin SATA3G1~2) 1-14

8. System panel connector (10-1 pin F_PANEL) 1-15

9. Clear RTC RAM (3-pin CLRTC) 1-7

1-3

1.3 Central Processing Unit (CPU)

J1800I-C

J1800I-C 204-pin DDR3 SO-DIMM sockets

DIMM_A1

DIMM_B1

J1800I-C

J1800I-C APU

APU

The motherboard comes with an onboard Intel® Celeron™ Dual-core Processor J1800 and a
specially designed CPU heatsink.

1.4 System memory

1.4.1 Overview

This motherboard comes with two Double Data Rate 3 (DDR3) Small Outline Dual Inline

Memory Modules (SO-DIMM) sockets. The gure illustrates the location of the DDR3 DIMM

sockets:

Channel Sockets

Channel A DIMM_A1

Channel B DIMM_B1

• Using both memory channels is supported on this motherboard. When installing 2 SO-

DIMMs, use the same size and type of memory. The DIMM_A1 slot should be lled in

order for the motherboard to work properly.

• This model supports a maximum total memory of of 8GB DDR3 1333 only. Memory

modules with a voltage higher than 1.35V will run at 1.35V. DDR3 1066Mhz memory

modules are not supported.

1-4

Chapter 1: Product introduction

1.4.2 Memory congurations

You may install 1GB, 2GB, 4GB and 8GB unbuffered non-ECC DDR3 SO-DIMMs into the
DIMM sockets.

• Always install DIMMs with the same CAS latency. For optimum compatibility, it is
recommended that you obtain memory modules from the same vendor.

• This motherboard does not support DIMMs made up of 256 megabits (Mb) chips or
less.

J1800I-C Series Motherboard Qualied Vendors Lists (QVL)

DDR3-1333 MHz capability

DIMM socket

Vendors Part No. Size SS/DS Chip Brand Chip NO. Timing Voltage

CRUCIAL CT102464BF1339.C16FER 8GB DS CRUCIAL CT512X8-1339 - 1.35V

G.SKILL F3-1333C9D-8GSL 4GB DS - K4B2G0846C 9-9-9-24 1.35V •

GEIL GGS38GB1333C9DC 4GB DS HYNIX H5TQ2G83CFR 9-9-9-24 1.3V •

DDR3-1600 MHz capability

Vendors Part No. Size SS/DS

KINGSTON KVR16LS11/4 4GB DS NANYA NT5CC512M8CN-DI - 1.35V •

SAMSUNG M473B5773DHO-YKO 1251 2GB DS - GEHXB8A3C - 1.35V •

SAMSUNG M471B5273EBO-CKO 1231 4GB DS - SEC231BCKDK4B2GO846E - 1.35V •

TRANSCEND TS512MSK64W6H 4GB DS - K4B4G0846B - 1.35V •

TRANSCEND TS1GSK64W6H 8GB DS - K4B4G0846B - 1.35V

ADATA ADDS1600W4G11-B 4GB DS ADATA QWND-1211AEL1329V - 1.35V •

ADATA ADDS1600W8G11-B 8GB DS ADATA QWND-1211AEL1329V - 1.35V

PQI MFCDR521UA0101 4GB DS PQI PQD312O8D12R - 1.35V •

PQI MFCDR621UA0103 8GB DS PQI PQD312O8D12R - 1.35V

Chip

Chip NO. Timing Voltage

Brand

support (Optional)

1 DIMM 2 DIMMs

DIMM socket
support (Optional)

1 DIMM 2 DIMMs

SS: Single-sided / DS: Double-sided

DIMM support:

• A*:

• B*:

• Using both memory channels is supported on this motherboard. When installing 2

•

• When installing memory with frequency higher than 1333Mhz, the motherboard will

Visit the ASUS website at www.asus.com for the latest QVL.

ASUS J1800I-C

Supports one module inserted into either slot.

Supports one pair of modules inserted into both the slots.

SO-DIMMs, use the same size and type of memory. The DIMM_A1 slot should be
lled in order for the motherboard to work properly.

Memory modules with a voltage higher than 1.35V will run at 1.35V.

automatically run the memory at 1333Mhz. DDR3 1066Mhz memory modules are not

supported.

1-5

1.5 Expansion slots

In the future, you may need to install expansion cards. The following sub-sections describe
the slots and the expansion cards that they support.

Unplug the power cord before adding or removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard components.

1.5.1 Installing an expansion card

To install an expansion card:

1. Before installing the expansion card, read the documentation that came with it and
make the necessary hardware settings for the card.

2. Remove the system unit cover (if your motherboard is already installed in a chassis).

3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later
use.

4. Align the card connector with the slot and press rmly until the card is completely

seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier.

6. Replace the system cover.

1.5.2 Conguring an expansion card

After installing the expansion card, congure it by adjusting the software settings.

1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for
information on BIOS setup.

2. Assign an IRQ to the card.

3. Install the software drivers for the expansion card.

1.5.3 PCI Express 2.0 x1 slot

This motherboard supports PCI Express 2.0 x1 network cards, SCSI cards, and other cards

that comply with the PCI Express specications.

IRQ assignments for this motherboard

Component A B C D E F G H

SATA Controller – – – shared – – – –

HD Audio – – – – – – shared –

USB 3.0 – – – – shared – – –

USB 2.0 – – – – – – – shared

LAN – shared – – – – – –

PCIE x1_1 – – shared – – – – –

WLAN – – – shared – – – –

1-6

Chapter 1: Product introduction

1.6 Jumpers

J1800I-C

J1800I-C Clear RTC RAM

1 2

2 3

Normal

(Default)

Clear RTC

CLRTC

1. Clear RTC RAM (3-pin CLRTC)

This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing
the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in
CMOS, which include system setup information such as system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3
for about 5-10 seconds, then move the cap back to pins 1-2.

3. Plug the power cord and turn ON the computer.

4. Hold down the <
enter data.

Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default
position. Removing the cap will cause system boot failure!

Del> key during the boot process and enter BIOS setup to re-

ASUS J1800I-C

• If the steps above do not help, remove the onboard battery and move the jumper
again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the
battery.

• You do not need to clear the RTC when the system hangs due to overclocking. For
system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature.
Shut down and reboot the system, then the BIOS automatically resets parameter
settings to default values.

1-7

J1800I-C

1 2

2 3

+5V

(Default)

+5VSB

KBPWR

J1800I-C Keyboard power setting

J1800I-C

J1800I-C USB device wake up

21

2 3

+5V

(Default)

+5VSB

USBPWB

J1800I-C

J1800I-C USB device wake up

21

2 3

+5V

(Default)

+5VSB

USBPWF

2. Keyboard power (3-pin KBPWR)

This jumper allows you to enable or disable the keyboard wake-up feature. When you
set this jumper to pins 2–3 (+5VSB), you can wake up the computer by pressing a key
on the keyboard. This feature requires an ATX power supply that can supply at least 1A
on the +5VSB lead, and a corresponding setting in the BIOS.

3. USB device wake-up (3-pin USBPWB)

Set this jumper to +5V to wake up the computer from S1 sleep mode (CPU stopped,
DRAM refreshed, system running in low power mode) using the connected USB
devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU,
DRAM in slow refresh, power supply in reduced power mode).

4. USB device wake-up (3-pin USBPWF)

Set this jumper to +5V to wake up the computer from S1 sleep mode (CPU stopped,
DRAM refreshed, system running in low power mode) using the connected USB
devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU,
DRAM in slow refresh, power supply in reduced power mode).

1-8

Chapter 1: Product introduction

1.7 Connectors

5

9

6 7

8

2

10

3 41

1.7.1 Rear panel connectors

1. PS/2 Keyboard / Mouse Combo port. This port is for a PS/2 keyboard or mouse.

2. LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)

through a network hub. Refer to the table below for the LAN port LED indications.

LAN port LED indications

LED

LAN port

Speed

LED

Activity/Link LED Speed LED

Activity Link

Status Description Status Description

OFF No link OFF 10Mbps connection
ORANGE Linked ORANGE 100Mbps connection
BLINKING Data activity GREEN 1Gbps connection

3. USB 3.0 port. This 9-pin Universal Serial Bus (USB) ports is available for connecting

USB 3.0 devices.

• DO NOT connect a keyboard / mouse to any USB 3.0 port when installing a Windows
operating system.

• Due to USB 3.0 controller limitations, USB 3.0 devices can only be used under a
Windows® OS environment after installing the USB 3.0 driver.

• USB 3.0 devices can be used for data storage only.

• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for a
faster and better performance from your USB 3.0 devices.

®

4. HDMI port. This port is for a High-Denition Multimedia Interface (HDMI) connector,

and is HDCP compliant allowing playback of HD DVD, Blu-Ray, and other protected
content.

ASUS J1800I-C

1-9

5. Serial port (COM2). This port connects a modem, or other devices that conform with

serial specication.

Line In port (light blue). This port connects to a tape, CD, DVD player, or other audio

6.
source.

7. Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, 5.1,

and 7.1-channel congurations, the function of this port becomes Front Speaker Out.

8. Microphone port (pink). This port connects to a microphone.

Refer to the audio conguration table for the function of the audio ports in a 2.1, 4.1, 5.1 or

7.1-channel conguration.

Audio 2.1, 4.1, 5.1 or 7.1-channel conguration

output.

Headset

2.1-channel

Line In Rear Speaker Out Rear Speaker Out Rear Speaker Out

4.1-channel 5.1-channel 7.1-channel

Port

Light Blue

(Rear panel)

Lime (Rear panel) Line Out Front Speaker Out Front Speaker Out Front Speaker Out

Pink (Rear panel) Mic In Mic In Bass/Center Bass/Center

Lime (Front panel) — — — Side Speaker Out

To congure an 8-channel audio output:

Use a chassis with HD audio module in the front panel to support an 8-channel audio

9. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other
VGA-compatible devices

10. USB 2.0 ports 1~4. These four 4-pin Universal Serial Bus (USB) ports are for USB

2.0/1.1 devices.

1-10

Chapter 1: Product introduction