Motherboard
ITX-220
E4590_ITX-220.indb 1 4/9/09 5:09:44 PM
ii
E4590
First Edition V1
April 2009
Copyright © 2009 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
E4590_ITX-220.indb 2 4/9/09 5:09:45 PM
iii
Contents
Notices .......................................................................................................... v
Safety information ...................................................................................... vi
About this guide ......................................................................................... vi
ITX-220 specications summary ............................................................. viii
Chapter 1: Product introduction
1.1 Before you proceed ..................................................................... 1-1
1.2 Motherboard overview ................................................................. 1-2
1.2.1 Motherboard layout ......................................................... 1-2
1.2.2 Layout contents ............................................................... 1-2
1.3 Central Processing Unit (CPU) ................................................... 1-3
1.4 System memory ........................................................................... 1-4
1.4.1 Overview ......................................................................... 1-4
1.4.2 Memory congurations .................................................... 1-4
1.5 Expansion slot .............................................................................. 1-6
1.5.1 Installing an expansion card ........................................... 1-6
1.5.2 Conguring an expansion card ....................................... 1-6
1.5.3 PCI slot ........................................................................... 1-6
1.6 Jumpers ........................................................................................ 1-7
1.7 Connectors ................................................................................... 1-8
1.7.1 Rear panel connectors .................................................... 1-8
1.7.2 Internal connectors ......................................................... 1-9
1.8 Software support ........................................................................ 1-14
1.8.1 Installing an operating system ...................................... 1-14
1.8.2 Support DVD information .............................................. 1-14
Chapter 2: BIOS information
2.1 Managing and updating your BIOS ............................................ 2-1
2.1.1 ASUS Update utility ........................................................ 2-1
2.1.2 ASUS EZ Flash 2 utility ................................................... 2-2
2.1.3 ASUS CrashFree BIOS 3 utility ...................................... 2-3
2.2 BIOS setup program .................................................................... 2-4
2.3 Main menu .................................................................................... 2-5
2.3.1 System Time ................................................................... 2-5
2.3.2 System Date ................................................................... 2-5
2.3.3 SATA 1/SATA 2 .................................................................................2-5
E4590_ITX-220.indb 3 4/9/09 5:09:47 PM
iv
Contents
2.3.4 Storage Conguration ..................................................... 2-6
2.3.5 System Information ......................................................... 2-6
2.4 Advanced menu ........................................................................... 2-7
2.4.1 JumperFree Conguration .............................................. 2-7
2.4.2 TPM Conguration .......................................................... 2-7
2.4.3 USB Conguration .......................................................... 2-8
2.4.4 CPU Conguration .......................................................... 2-9
2.4.5 Chipset ............................................................................ 2-9
2.4.6 Onboard Devices Conguration .................................... 2-10
2.4.7 PCI PnP ........................................................................ 2-10
2.5 Power menu ................................................................................ 2-11
2.5.1 Suspend Mode ...............................................................2-11
2.5.2 ACPI 2.0 Support ...........................................................2-11
2.5.3 ACPI APIC Support ........................................................2-11
2.5.4 APM Conguration ........................................................ 2-12
2.5.5 Hardware Monitor ......................................................... 2-12
2.6 Boot menu .................................................................................. 2-13
2.6.1 Boot Device Priority ...................................................... 2-13
2.6.2 Boot Settings Conguration .......................................... 2-13
2.6.3 Security ......................................................................... 2-14
2.7 Tools menu ................................................................................. 2-16
2.7.1 AI NET 2........................................................................ 2-16
2.7.2 ASUS EZ Flash 2 .......................................................... 2-16
2.8 Exit menu .................................................................................... 2-16
E4590_ITX-220.indb 4 4/9/09 5:09:48 PM
v
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://green.asus.com/english/REACH.htm.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
E4590_ITX-220.indb 5 4/9/09 5:09:55 PM
vi
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
•
Seek professional assistance before using an adpater or extension cord. These devices
could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your area. If you are
not sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.
•
Before using the product, make sure all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualied service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and conguring the
motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it
supports.
• Chapter 2: BIOS information
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
E4590_ITX-220.indb 6 4/9/09 5:09:56 PM
vii
Where to nd more information
Refer to the following sources for additional information and for product and software
updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as warranty yers,
that may have been added by your dealer. These documents are not part of the
standard package.
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
NOTE: Tips and additional information to help you complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
Typography
Bold text Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<D>
E4590_ITX-220.indb 7 4/9/09 5:09:59 PM
viii
ITX-220 specications summary
(continued on the next page)
CPU Integrated Intel® Celeron® 220 processor
Supports Intel® EM64T technology
Chipset Northbridge: Intel® 945GC
Southbridge: Intel® ICH7
CPU Fan Fan Dimensions: 40 x 40 x10mm
Rated Speed: 5000 ± 10% RPM
Rated Voltage: DC 12V
Maximum Air Flow: 5.57 CFM
Noise Level: 25.3 dBA (Max. 27.5 dBA)
Front Side Bus 533 MHz
Memory Dual channel memory architecture
- 2 x 240-pin DIMM sockets support unbuffered
non-ECC 533 MHz DDR2 memory modules
- Supports up to 4GB system memory
* Refer to www.asus.com or this user manual for the
Memory QVL (Qualied Vendors Lists).
** When you install a total memory of 4GB capacity
or more, Windows® 32-bit operating system may only
recognize less than 3GB. We recommend a maximum
of 3GB system memory if you are using a Windows®
32-bit operating system.
Graphics Integrated Intel® Graphics Media Accelerator 950
Supports D-Sub with max. resolution of 2048 x 1536 x
32 Bpp @75Hz
Maximum shared memory of 224MB
Expansion slot 1 x PCI slot
Storage Intel® ICH7 SouthBridge supports:
- 2 x Serial ATA 3Gb/s ports
Audio VIA VT1705 High Denition Audio 6-channel CODEC
LAN Realtek® PCIe Gb LAN controller
USB Supports up to 6 USB 2.0/1.1 ports (2 ports at mid-board,
4 ports at back panel)
ASUS special features ASUS CrashFree BIOS 3
ASUS EZ Flash 2
ASUS MyLogo 2™
ASUS AI NET 2
Rear panel ports 1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x VGA port
1 x COM port
1 x LAN (RJ-45) port
4 x USB 2.0 ports
6-channel audio I/O ports
E4590_ITX-220.indb 8 4/9/09 5:10:00 PM
ix
ITX-220 specications summary
*Specications are subject to change without notice.
Internal connectors 1 x USB connector supports additional 2 USB ports
1 x Speaker connector
2 x Serial ATA connectors
1 x Chassis fan connector
1 x Chassis intrusion connector
1 x CPU fan connector
1 x TPM connector (optional)
1 x System panel connector
1 x High denition front panel audio connector
1 x 24-pin EATX power connector
1 x 4-pin ATX 12V power connector
BIOS features 8 Mb Flash ROM, AMI BIOS, PnP, DMI v2.0, WfM 2.0,
SMBIOS 2.5, ACPI v2.0a
Accessories 1 x Serial ATA cable
1 x I/O shield
Support DVD contents Drivers
ASUS PC Probe II
ASUS Update
Anti-virus software (OEM version)
User Manual
Form Factor Mini ITX form factor: 6.75 in x 6.75 in (17.1cm x 17.1cm)
E4590_ITX-220.indb 9 4/9/09 5:10:01 PM
ASUS ITX-220 1-1
Chapter 1
Product introduction
If any of the items is damaged or missing, contact your retailer.
Thank you for buying an ASUS® ITX-220 motherboard!
Before you start installing the motherboard, and hardware devices on it, check the items in
your motherboard package. Refer to page ix for the list of accessories.
1.1 Before you proceed
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
• Unplug the power cord from the wall socket before touching any component.
• Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due to
static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
• Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
Onboard LED
The motherboard comes with a standby power LED that lights up to indicate that the system
is ON, in sleep mode, or in soft-off mode. This is a reminder that you must shut down
the system and unplug the power cable before removing or plugging in any motherboard
component. The illustration below shows the location of the onboard LED.
E4590_ITX-220.indb 1 4/9/09 5:10:04 PM
1-2 Chapter 1: Product introduction
1.2.2 Layout contents
1.2 Motherboard overview
1.2.1 Motherboard layout
Place four screws into the holes indicated by circles to secure the motherboard to the
chassis. DO NOT overtighten the screws! Doing so can damage the motherboard.
Ensure that you install the motherboard into the chassis in the correct orientation. The edge
with external ports goes to the rear part of the chassis.
Place this side towards
the rear of the chassis.
Connectors/Jumpers/Slots/LED Page Connectors/Jumpers/Slots/LED Page
1. Keyboard/mouse power (3-pin PS2_USBPW1-6) 1-7 8. Standby power LED (SB_PWR) 1-1
2.
ATX power connectors (24-pin EATXPWR, 4-pin
ATX12V)
1-9 9.
System panel connector (10-1 pin
F_PANEL)
1-12
3. Speaker connector (4-pin SPEAKER) 1-10 10. Clear RTC RAM (3-pin CLRTC) 1-7
4. USB connector (10-1 pin USB56) 1-10 11.
Chassis intrusion connector (4-1 pin
CHASSIS)
1-11
5. CPU Socket 1-3 12. PCI slot 1-6
6.
CPU and chassis fan connectors (3-pin
CPU_FAN, 3-pin CHA_FAN)
1-11 13.
Serial ATA connectors (7-pin SATA1,
SATA2)
1-13
7. DDR2 DIMM slots 1-4 14.
Front panel audio connector (10-1 pin
AAFP)
1-13
E4590_ITX-220.indb 2 4/9/09 5:10:08 PM
ASUS ITX-220 1-3
1.3 Central Processing Unit (CPU)
The motherboard comes with an onboard Intel® Celeron® 220 processor and a specially
designed CPU heatsink and fan.
Ensure that the CPU fan cable is connected to the onboard CPU_Fan connector.
E4590_ITX-220.indb 3 4/9/09 5:10:10 PM
Loading...