Astro Pneumatic ADG100 User Manual

MODEL: PRODUCT TYPE:

ADG100

GREASE GUN DRILL ADAPTER

WARNING

Study, understand and follow all instructions provided with
this product. Read these instructions carefully before
installing, operating, servicing or repairing this tool. Keep
these instructions in a safe accessible place.

INTENDED USE OF THE TOOL 1 YEAR LIMITED WARRANTY

This tool is designed to be used with corded, cordless
or air screw drivers, drills and impact drivers for the
purpose of dispensing and packing grease only. Do not
use this tool outside of the designed intent. Never modify
the tool for any other purpose or use.

WARNING

Caution: To help prevent personal injury

• Normal use of this product is likely to expose the user

to dust and/or microscopic particles containing
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Always wear appropriate safety equipment and
clothing when using this product. Study, understand
and follow all instructions provided with this product.
Failure to read and follow all warnings and operating
instructions may result in damages and serious injury
or death.

• Always wear ANSI approved goggles when using this
product. (Users and By standers).

• Never use this tool for any application other than for

which it was designed.

• Only use accessories designed for this tool.

• Never alter or modify this tool in any way.

• Improper operation and/or maintenance of the tool,

modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.

• Always select the correct accessories of the correct

size and design for the job that you are attempting to
perform.

• Always work in a clean, safe, well-lit, organized and

adequately equipped area.

• Do not begin repairs without assurance that vehicle

is in secure position, and will not move during repair.

• Astro Pneumatic Tool Co. warrants our products to the original
user against defective material or workmanship for a period of 1
year (except where noted on our price schedule) from the date of
1st use. Astro reserves the right to determine whether the product
failed because of defective material, workmanship or other causes
and to charge back for missing parts. Astro Pneumatic Tool Co., at
its discretion, will repair products covered under this warranty free of
charge. The distributor should direct the original user to return the
product (with the exceptions listed below) with the distributor’s
name, address, adequate proof of date of purchase or a copy of
warranty card, and a short note explaining the problem. Failures

caused by accident, alteration, or misuse are not covered by
this warranty.

• If one part of this product fails, please do not return the entire
product. Astro will replace free of charge component parts of
this product that fail within 1 year of first use by the original
user. Items included in this category include but are not
limited to kits, hand tool kits and any other product where there
are multiple items or components that make up the unit. Please
contact the phone number below in order to obtain the
replacement components covered under warranty.

• Astro Pneumatic Tool Co. or its authorized service representatives
must perform all warranty repairs. Any repair to the product by
unauthorized service representatives voids this warranty. The rights
under this warranty are limited to the original user and may not be
transferred to subsequent owners.

• This warranty is in lieu of all other warranties, expressed or
implied, including warranties of merchantability and fitness for a
particular purpose. Some states do not allow the exclusion of
limitations of incidental or consequential damages so the above
limitations may not apply to you.

PLEASE DO N OT RETURN ANY PROD UCT WITHOUT CALL ING

When unpacking, check the parts diagram and part
number listing on page 7 to make sure all parts are
included. If any parts are missing or damaged,
please call your distributor.

PRODUCT INFORMATION:

• Easily convert cordless drills and impact drivers into
cordless power grease guns

• 1/4" hex drive with adjustable bracket to fit nearly

all cordless, corded and air drivers

• Works with standard 14-14.5 oz. grease tubes, or bulk fill

• 4,000psi working pressure, 8,000psi max pressure

• Includes 18" nylon hose w/ locking coupler

GREASE GUN
DRILL ADAPTER

MADE IN CHINA

Page 1

DO NOT DISCARD – GIVE TO USER

www.astrotools.com

1-800-221-9705 FOR INSTRUCTIONS

Before Use

MODEL: PRODUCT TYPE:

ADG100

GREASE GUN DRILL ADAPTER

I. SPECIFICATIONS OF UNIVERSAL POWER COUPLING-GREASER

• Working Pressure: 4,000 psi

• Max Pressure: 8,000 psi (9,000 psi safety vent)

• Capacity: 14-14.5 oz.

• 3-Way Loading: Cartridge / Dispenser / Bulk

WARNING

• Do not exceed recommended pressure during
operation to avoid serious injury or facilities
damage.

• Read your power tool’s safety instruction manual
carefully before using this universal grease
adapter.

• What’s included: (Power tool is not included.)

- Grease Gun Adapter

- 18" Nylon Hose w/ Locking Coupler

- Adjustable Holder

II. CATEGORIES OF COMPATIBLE POWER TOOLS & SAFETY INSTRUCTIONS FOR USE

Cordless Drill Driver

(Keyless Chuck type)
3/8" (9.5mm)
1/2" (13mm)

Impact Driver

(Hex. Drive shank chuck)
1/4" (6.35mm)

Impact Wrench

(Square Drive)
3/8" (9.5mm),
1/2" (13mm)
(adaptor needed,
not included)

Air Drill

(Key chuck type)
3/8" (9.5mm)
1/2" (13mm)

Corded Drill

(Key chuck type)
3/8" (9.5 mm)
1/2" (13mm)

Holder

Adjusts from 1.5-3"
to fit all of the above
power tools

WARNING

• Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.

• Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your
mains-operated(corded) power tool or battery-operated(cordless) power tool or air power tool.

Page 2

MODEL: PRODUCT TYPE:

III. INSTRUCTIONS

PRESSURE-VENT
PROTECTOR

ADG100 GREASE GUN DRILL ADAPTER

BOTTOM

CONTAINER TUBE

GUN HEAD

CAP

PLUNGER
HANDLE

STOPPER

AIR VENT VALVE

18" HIGH PRESSURE
NYLON HOSE

GEAR CAP

HOLDER

BUTTERFLY
LOCK PLUG

SHANK

GEAR HOUSING

(Power tool is not included)

IV. FUNCTIONAL DESCRIPTION

NOTE:

• The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the power tool.

• Never operate, or attempt any maintenance on the tool unless you have first read and understand all safety

instructions contained in your power tool’s manual.

• Some illustrations in this Instruction Manual may show details or attachments that differ from those on your

own power tool.

V. HOW TO ASSEMBLE

1. Load grease cartridge or pack container tube before use. (See instructions on Page 5)

2. Remove any bits, parts or attachment currently in your power tool's chuck.

3. Unscrew the chuck. Join and couple your power tool to the shank of
the grease gun adapter via the chuck properly (around 1/4-5/16" from
gear housing). Tighten chuck securely.

4. Unscrew the butterfly lock plug to allow proper room for the container tube
and your power Tool. Install the holder in the space between container tube
and power tool.

5. Adjust the holder to proper position. (available inner width for power tool is

1.5" to 3"). Tighten the butterfly lock plug securely.

6. Install the 18" nylon hose to the gun head and tighten with a wrench securely.

Page 3