Astro Pneumatic 600PT User Manual

Model:

600PT

Foreseen Use of the Tool

Do not use the tool outside of the design intent.
Never modify the tool for any other purpose, or for its use.

Safety Precaution

Caution: To help prevent personal injury

Product Type:

PISTOL GRIP PUNCH/FLANGE TOOL
WITH 5.5MM PUNCH

www.astrotools.com

Normal use of this product is likely to expose

•

the user to dust and/or microscopic particles
containing chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm. Always wear
appropriate safety equipment and clothing when
using this product. Study, understand and follow
all instructions provided with this product.

•

Always wear ANSI approved goggles when using
this product.

•

Always select the correct accessories of the
correct size and design for the job that you are
attempting to perform.

•

Always work in a clean, safe, well-lit, organized
and adequately equipped area.

Do not begin repairs without assurance that

•

vehicle is in secure position, and will not move
during repair.

PRODUCT INFORMATION

1 YEAR LIMITED WARRANTY

•Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year from the date of 1st use.
Astro reserves the right to determine whether the product failed because of defective
material, workmanship or other causes and to charge back for missing parts. Astro
Pneumatic Tool Co., at its discretion, will repair products covered under this warranty
free of charge. The original user is to return the product (with the exceptions listed
below) with the distributor’s name, address, adequate proof of date of purchase or a
copy of warranty card, and a short note explaining the problem. Failures caused

by accident, alteration, or misuse are not covered by this warranty.

•Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user
and may not be transferred to subsequent owners.

•This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you. All claims must be sent to:

Astro Pneumatic Tool Company
P.O. Box 251935
Los Angeles, CA 90025

PLEASE DO NOT RETUR N ANY PRODUCT TO THE P.O. BOX.

CALL 1-800-221-9705 FOR INSTRUCTIONS.

Unpacking

When unpacking, check the parts diagram and part number listing
on page 2 to make sure all parts are included. If any parts are
missing or damage, please call your distributor.

• Punch designed for easy replacement

• Performs hole punching and panel crimping

• Features a rotating head for convenient use

• Every pull of the lever delivers a single punch or a
single flange crimp with precision control

• Forms an offset crimped edge on sheet metals for
no-bump lap welds

• Lightweight, yet ruggedly built

• Cuts metal fabrication time in half

Important

Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in
a safe accessible place.

PISTOL GRIP PUNCH/FLANGE TOOL
WITH 5.5MM PUNCH

Specifications:

Punch Capacity:
Piston Stroke:
Overall Length:
Net Weight:
Air Inlet Thread NPT:
Air Hose I.D. Size:
Avg. Air Consumpt.:
Air Pressure:

1

7/32” (5.5mm)
5/32” (4mm)
7-1/2” (191mm)
2-1/4lbs. (1.0kg)
1/4”
3/8” (10mm)
4cfm
90-120psi

600PT

PISTOL GRIP PUNCH/FLANGE TOOL
WITH 5.5MM PUNCH

600PT-B01
600PT-B02
600PT-B03
600PT-B05
600PT-B06
600PT-B10
600PT-B11
600PT-B12
600PT-B13
600PT-B14
600PT-B15
600PT-B16
600PT-B17
600PT-B19
600PT-B20
600PT-B21
600PT-B22

Body Housing 1
O-Ring (P8) 2
Back up Ring (P8) 2
Spring 1
Piston 1
O-Ring (37.69x3.53) 1
Throttle Lever 1
Pin Valve 1
O-Ring (P4) 2
O-Ring (P9) 1
Valve Bushing 1
O-Ring (P9) 1
Throttle Valve 1
Spring 1
Lever Pin (M3x23) 1
Clamp A 1
Clamp B 1

600PT-B24
600PT-B25
600PT-B26
600PT-B27
600PT-B28
600PT-B29
600PT-B30
600PT-B31
600PT-B32
600PT-B33
600PT-B34
600PT-B35
600PT-B36
600PT-B37
600PT-B38
600PT-B39
600PT-B40 Air Inlet 1

2

Set Screw (M6x6) 1
Punch Die 1
Guide Bushing (M5.5) 1
Spring Washer (M5.5)
Punch (M5.5)
Cover Plate (M5.5) 1
Screw (M4x6) 2
Oil Seal 1
Support Ring (P12) 1
O-Ring (P12) 1
Oil Plug 1
O-Ring (P5) 1
Lock Nut 1
O-Ring (P34) 1
Support Ring 1
Piston 1

13

1