AstroJet
2650P-2800P
Quick Start Guide
Step 1
Unpack Printer and Accessories
Place Printer on a stable surface at least 12”
from any walls. Save packaging material.
Attach Side Media Guides, Rear Media Support
and Rear Media Guide.
Step 2
Connect Power to Printer
1. Main power switch is turned OFF.
2. Plug power cord into Printer receptacle.
3. Plug other end into 115-220 Volt AC, 50/60 Hz.
grounded outlet.
DO NOT TURN POWER SWITCH ON YET
Connect Printer to Computer
Printer has both USB and Parallel Ports.
(Located on Side Cover as shown.)
USB Cable Users: Plug USB cable from computer into Printer’s
USB port.
Parallel Cable Users: Plug Parallel Printer Cable from computer
into Printer’s Parallel Port. Latch two locking clips.
Page 1
Ink in cartridge may be harmful if
swallowed. Keep new and used
cartridges out of reach of
children. Discard empty
cartridges immediately.
Step 3
Install Inkjet Cartridges
2650P holds up to 6 Inkjet Cartridges.
2800P holds up to 8 Inket Cartridges.
1. Remove inkjet
cartridge from
packaging.
DO NOT touch
copper contacts,
metal plate, or gold
printhead. Remove
protective tape from
printhead.
2. Open latch levers
on inkjet cartridge
holders.
3. With cartridge’s
printhead pointing
down, slide
cartridge into
holder, push down
and toward contacts
in holder.
Step 4
Setting Up Feed
1. Release Separator Locking Levers (located on
operator’s side of Feeder), raise Separators an
lock in position. Move Side Guides to outermost
open position. Place one piece of media in
center of Feed Table.
2. Four Separators on Feeder. Use two Center
Separators for narrow media and all four
Separators for wide media. Place media under
Separators and lower Separators onto media.
4. Make sure cartridge
is seated in holder.
Close latch lever to
secure cartridge in
holder.
DO NOT force
lever into place.
5. Repeat Steps 1-4
for remaining
cartridges.
3. Rotate Locking Lever up to lock Separators
in place.
4. Loosen knobs on Side Guides. Adjust Side
Guides to within 1/32” of media. Tighten knobs.
5. Adjust Rear Guide so media is raised
approximately 1/2” and rests on curve of Rear
Guide. When running 10” or longer or heavy
media Rear Guide may have to be set so it just
touches back of media.
Page 2
Media Thickness
Dial Setting
0.004" to 1/32"
0 to 2
1/32" to 1/8"
2 to 3
1/8" to 5/16"
3 to 7
5/16" to 3/8"
7 to 10
6. Feed one piece of media through Printer. Adjust
two Exit Guides to ride on media.
NOTE: To prevent smearing, make sure Exit
Guides do not track over any printed
information.
7. Turn Printer ON. Turn Media Thickness Knob to
set initial Printhead height as follows:
Step 5
Install Print Driver
Load “Printer Drivers”
CD into computer's
CD/DVD drive.
If “Drive Installation CD”
launch window appears,
you can ignore it.
DO NOT TURN PRINTER POWER ON YET
1. With Printer connected to computer via USB or
parallel port, turn Printer ON. In a few minutes
“Welcome to the Add New Printer Wizard”
opens. Click Next>.
NOTE: These are initial settings. It may be
necessary to adjust Media Thickness Control to
optimize print quality.
8. Press ONLINE.
Press ENTER to test-feed media.
2. “User Information” screen. Type in your
company and name. Click Next>.
Page 3
© 2014 Astro Machine Corp 10/30/2014
AJ 2650P-2800P Quick Start Guide
630 Lively Blvd.
Elk Grove Village, IL 60007
Phone: (847) 364-6363
Fax: (847) 364 9898
www.astromachine.com
3. Select your Printer Model from list displayed.
Click Next>.
4. Select Printer Port: LPT1 for parallel cable
connection or USB for USB connection.
Click Next>.
5. “Name your Printer” screen. Unless another
Printer of same name is on your system or
network you can ignore this step.
(You can also choose to make this Printer the
default printer.) Click Next>.
6. “Completing the Add Printer Wizard” window.
Click Finish to complete installation. Installation
is complete when “Found New Hardware” box
appears in lower right-hand corner of screen.
Step 6
To install Accessories and for Printer set-up or
operation, please refer to “AstroJet 2650P-2800P
Printer Operator Manual” supplied with Printer.
Page 4
Loading...