Astro 557010 User Manual

557010

ADJUSTABLE EXTRA HEAVY DUTY PORTABLE WORK STAND

www.astrotools.com

•

Normal use of this product is likely to expose the user to dust and/or microscopic particles containing chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Always wear appropriate safety equipment and clothing when using this product. Study, understand and follow all instructions provided with this product.

•

Always wear ANSI approved goggles when using this product.

•

Always select the correct accessories of the correct size and design for the job that you are attempting to perform.

•

Always work in a clean, safe, well-lit, organized and adequately equipped area.

•

Do not begin repairs without assurance that vehicle is in secure position, and will not move during repair.

Product Information

• Heavy Duty work bench with capacity of 500lbs.

• Heavier gauge tubing (31.74mm)

• 1-1/4" Steel tubing construction with 1/2" foam padded top

• Great for working on doors, fenders, hoods and bumpers

• Adjustable height of 25" to 41" tall

• Stand Dimensions in Completely Folded Position: 40" wide x 42" high

• Stand Dimensions in Adjustable Operating Position: Maximum Height: 14" depth x 41" high x 40" wide Minimum Height: 32" depth x 25" high x 40" wide

• Tubing diameter is 1-1/4" (32mm)

• Weight: 16lbs.

Astro Pneumatic Tool Co. warrants our products to the original user against defective material or workmanship for a period of 1 year from the date of 1st use. Astro reserves the right to determine whether the product failed because of defective material, workmanship or other causes and to charge back for missing par ts. Astro Pneumatic Tool Co., at its discretion, will repair products covered under this war ranty free of charge. The original user is to return the product (with the exceptions listed below) with the distributor’s name, address, adequate proof of date of purchase or a copy of warrant y card, and a shor t note explaining the problem. Failures caused by accident,

alteration, or misuse are not covered by this warranty.

Astro Pneumatic Tool Co. or its authorized service representatives must per form all warrant y repairs. Any repair to the product by unauthorized service representatives voids this warranty. The rights under this warranty are limited to the original user and may not be transferred to subsequent owners.

This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose. Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitations may not apply to you.

PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING

1-800-221-9705 FOR INSTRUCTIONS.

Unpacking

When unpacking, check the parts diagram and part number listing on page 2 to make sure all parts are included. If any parts are missing or damaged, please call your distributor.

ADJUSTABLE EXTRA HEAVY DUTY

PORTABLE WORK STAND

Important

MADE IN CHINA

372 Old US Highway 52 South Mount A iry, NC 27030

ADJUSTABLE EXTRA HEAVY DUTY

557010

Call 1.800.221.9705 for questions concerning performance of the product or other inquiries.

Fig. A

PORTABLE WORK STAND

Fig. B

Index

No.

1 2 3 4 6 7 8

Fig. B

557010-A01 557010-A02 557010-A03 557010-A04 557010-A06 557010-A07 557010-A08

Fig. A

Foam Pad Rubber Cover Chain with Eye Bolt- 10.5" Eye Hook Assembly Lock Nut M8 Washer M8x16mm Leg Tube

3 67 7

1 2

11 12

3 4

8 9 10 11

Index

No.

557010-A09

2 4 2 2 4 8 4

9 10 11 12 13 14

557010-A10 557010-A11 557010-A12 557010-A13 557010-A14

Outer Top Frame Tube Inner Top Frame Tube Bolt M10 x 75mm Washer M10 x 30 x 3mm M10 Lock Nut Washer M10 x 20 x 1mm

12 13 14

1 1 2 2 2 4

Assembly Instruction

Metal edges can be sharp, please use extreme caution during assembly.

1. Attach rubber end caps (#2) to four leg tubes (#8).

2. Slide foam pad (#1) onto both outer top frame tube (#9) and inner top frame tube (#10). Then, slide leg tubes (#8) into both frame tubes. Match up holes.

3. Add a flat washer (#7) to eye bolt (# 3). Do not disturb fixed nuts on both eye bolts and eye hook assemblies. And, push eye bolt (# 3) thru holes of leg tube (#8) and outer top frame tube (#9) assembly (see Figure A). Assemble so that the eye bolt (# 3) is on the inside of the work bench. Add a second flat washer (#7) and lock nut (#6) and tighten snugly. Repeat the same steps for the second set of legs. When complete and the work bench is assembled, the eye bolts (#3) will be on the opposite sides facing inwards.

4. Slide leg tubes (#8) into inner top frame tube (#10). Twist legs until the holes are aligned. Assemble eye hook assemblies (#4) duplicating the same assembly process as in step #3, all eye bolts and eye hook assemblies are facing inward when complete. When the work bench is assembled, the chains with eye bolts and eye hook assemblies will be on opposite sides facing inwards.

5. Set up both parts of the stand so that the eye bolts with chains (#3) and eye hook assemblies (#4) are on opposite sides facing inside of work bench. Attach eye bolts chains to eye hook assemblies on the opposite sides of the work bench. Attach both halves (#8) together with a bolt (#11) a flat washer (#14) and a special washer (#12) inserted between both legs (see Figure B). And finally put a third flat washer (#14) before adding lock nut (#13) onto the bolt.

6. Last, tighten all fasteners when completely assembled. Do not over tighten as the tubing can crush.

Please make sure the chain and hook assemblies on both sides of the stand are adjusted to equal lengths. See Figure C.

Page 2

Figure C