Page 1
Model:
Product Type:
3056
WARNING
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing,
operating, servicing or repairing this tool. Keep these instructions
in a safe accessible place.
INTENDED USE OF THE TOOL
This polisher is designed for buffing and polishing painted
surfaces. Do not use this tool outside of the designed
intent. Never modify the tool for any other purpose or use.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using this
product. Stud y, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (User s and Bystander s).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
3” AIR COMPOSITE RANDOM ORBITAL SANDER KIT
3” AIR COMPOSITE POLISHING KIT
www.astrotools.com
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. Astro reserves the right to determine whether the
product failed because of defective material, workmanship or other causes and to charge
back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products
covered under this warranty free of charge. The distributor should direct the original user
to return the product (with the exceptions listed below) with the distributor’s name,
address, adequate proof of date of purchase or a copy of warranty card, and a short note
explaining the problem. Failures caused by accident, alteration, or misuse are not
covered by this warranty.
• If one part of this product fails, please do not return the entire product. Astro will
replace free of charge component parts of this product that fail within 1 year of first
use by the original user. Items included in this category include but are not limited
to kits, hand tool kits and any other product where there are multiple items or
components that make up the unit. Please contact the phone number below in
order to obtain the replacement components covered under warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and may
not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including warranties
of merchantability and fitness for a particular purpose. Some states do not allow the
exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
When unpacking, check the parts diagram and part number
listing on page 4 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
PRODUCT INFORMATION:
• Compact lightweight tool permits polishing in hard to reach areas
• Ergonomically designed pistol grip handle provides extra control
of movement and user comfort
• Composite body is durable and helps resist chemicals
• Kit includes:
1-3" Air Composite Polisher
1-3" Hook & Loop Backing Pad (#20302F)
1-3.5" Foam Compounding Pad - White
1-3.5" Foam Compounding Pad - Yellow
1-3.5" Wool Buffing Pad
1-Spanner Wrench
• Blow molded case for easy storage and transport
SPECIFICATIONS:
Spindle size: 5/16"-24T
Free Speed: 2100 RPM
Air Hose I.D. Size: 3/8" (10mm)
Air Pressure: 90-120 psi
Avg. Air Consumption: 3.5 cfm
Length: 135 mm (5.3")
Net Weight: 0.77kgs (1.70lbs)
1-800-221-9705 FOR INSTRUCTIONS
Unpacking
MADE IN TAIWAN
Page 1
DO NOT DISCARD – GIVE TO USER
Page 2
Model:
Product Type:
3056
3” AIR COMPOSITE POLISHING KIT
3” AIR COMPOSITE RANDOM ORBITAL SANDER KIT
Also Available Separately:
1. 20302F - 3" Velcro Back Up Pad with Female Threads
2. 4635 - 3” Yellow Diamont Cut Form Pad - Velcro
3. 4638 - 3” White Diamond Cut Polishing/Finishing Foam Pad
MADE IN TAIWAN
Page 2
Page 3
Model:
Product Type:
3056
3” AIR COMPOSITE POLISHING KIT
The oil and water extractor should not be mounted on or near the air
compressor.
The temperature of air is greatly increased during compression. As the air
cools down to room temperature, in the air line, on its way to the Air Power
Tool, the moisture contained in it condenses. Thus, for maximum
effectiveness, the oil and water extractor should be mounted at some point
SUGGESTED AIR LINE CONNECTION
Pitch pipe back toward air receiver
PIPE SIZE, I.D. (Inches)
Compressor unit
Drain
Daily
Air Flow
CFM
10
20
30
40
50
70
Oil and Water Extractor should be at least 25 ft. from the compressor. Further if possible.
Length of Pipe (feet)
50
1/2"
3/4"
3/4"
1"
1"
1"
in the air supply system where the temperature of the compressed air in the
line is likely to be lowest. Air lines must be properly drained daily. Each low
point in an air line acts as a water trap. Such points should be fitted with an
easily accessible drain. See diagram below. Pitch all air lines back towards
the compressor so that condensed moisture will flow back into the air
receiver where it can be drained off. Drain daily.
Install drain at
100
3/4"
3/4"
3/4"
1"
1"
1"
150
3/4"
3/4"
3/4"
1"
1"
1"
1-1/4"
1-1/4"
25 FEET OR MORE
200
1"
1"
1"
each low point
Drain
Daily
Oil and Water
Extractor
Drain
Daily
Page 3
Page 4
372 Old US Hig hway 52 South
Mount A iry, NC 27030
PARTS BREAKDOWN
21-1
15
22
21
17
20
Model: Product Type:
3” AIR COMPOSITE
3056
Call 1.800.221.9705 for questions concerning performance of the product
or other inquiries.
17
19
18
16
15
14
13
10
POLISHING KIT
12
11
11
10-1
8
9-1
9
29
31
28
27
26
30
25
26
24
23
7
Parts List
Index Part No. Description Qty Index Part No. Description Qty
1
2
3
4
5
6
7
8
9
9-1
10
10-1
11
12
13
14
15
16
3056-01
3056-02
3056-03
3056-04
3056-05
3056-06
3056-07
3056-08
3056-09
3056-09-1
3056-10
3056-10-1
3056-11
3056-12
3056-13
3056-14
3056-15
3056-16
Inlet Bushing
Deflector
Valve Spring
Valve
Valve Seat
Spacer
Silencer
Composite Housing
Reverse V alv e Lever
Taping Screw ( 2.3x12L)
Trigger
O-Ring (3X1)
O-ring (27x2)
Valve Body
Spring
Detent Ball (3mm)
Bearing (626zz)
Rear Plate
3056-17
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
17
18
19
20
21
21-1
22
23
24
25
26
27
28
29
30
31
3056-18
3056-19
3056-20
3056-21
3056-21-1
3056-22
3056-23
3056-24
3056-25
3056-26
3056-27
3056-28
3056-29
3056-30
20302F
Spring Pin
Rotor
Rotor Blade
Cylinder
Front Plate
Spring Pin (M2.5x4)
Pin ( 1.5x4.8l)
Idle Gear
Pin ( 4x15.6)
Spindle
Ball Bearing (6201zz)
Ring Gear
Front Housing
Spindle Nut
Wrench
3" Velcro Back Up Pad
with Female Threads
6
5
4
3
2
1
2
1
5
1
1
1
1
3
3
1
2
1
1
1
1
1
Page 4
20140311
Loading...