Astro 3018 User Manual [en, es, fr]

3018

Product Information

• Easy Change Chuck System

• 1 Button Operation

• Auto shut-off for increased battery life

• Displays KGF, BAR, PSI, KPA measurement

• Large face LCD digital read-out

• Unit covered with rubber sleeve for extra comfort and durability

• On Power Button, auto shut off in 90 seconds if not in use

• LCD Back Light

• Allows accurate reading of tire pressure, assisting with TPMS

(Tire Pressure Monitoring Systems)

• Two position lever. 1st position deflates, 2nd position inflates

• Works on a nitrogen system

• With 21" Hose

FUNCTION KEY:

1. ON/UNIT/LIGHT: Press once to turn on. Press again to turn on backlight.
When the unit is on, press for 3 seconds to switch units.

Specifications:

Measuring Range: 3 ~ 175psi
Units: PSI / BAR / KPA / KGF
Resolution: 0.1 PSI
Accuracy: Compliance with European Community
Council Directive 86/217/EEC
0 ~ 58 psi +/- 1.2 psi
59 ~ 174 psi +/- 2.0 psi
over 145psi,±3.6psi
Working Temperature: 32°F~104°F (=0°C~ 40°C)
Power: Lithium Batteries
Battery Lifetime: 140hr

DIGITAL TIRE INFLATOR

www.astrotools.com

1 YEAR LIMITED WARRANTY

• Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. Astro reserves the right to determine whether the
product failed because of defective material, workmanship or other causes and to charge
back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products
covered under this warranty free of charge. The distributor should direct the original user
to return the product (with the exceptions listed below) with the distributor’s name,
address, adequate proof of date of purchase or a copy of warranty card, and a short note
explaining the problem. Failures caused by accident, alteration, or misuse are not

covered by this warranty.

• If one part of this product fails, please do not return the entire product. Astro will
replace free of charge component parts of this product that fail within 1 year of first
use by the original user. Items included in this category include but are not limited
to kits, hand tool kits and any other product where there are multiple items or
components that make up the unit. Please contact the phone number below in
order to obtain the replacement components covered under warranty.

• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and may
not be transferred to subsequent owners.

• This warranty is in lieu of all other warranties, expressed or implied, including warranties
of merchantability and fitness for a particular purpose. Some states do not allow the
exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.

PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING

When unpacking, check the parts diagram and part number
listing on page 3 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.

1-800-221-9705 FOR INSTRUCTIONS

Unpacking

IMPORTANT

DIGITAL TIRE INFLATOR

MADE IN CHINA

Page 1

3018

DIGITAL TIRE INFLATOR

Operating Instruction

1. Remove tire valve cap.

2. With clip-on air chuck lever depressed, firmly press chuck onto tire valve stem and release lever, and ensure
that no air leaks.

3. Press the grip to inflate. Press the grip half-way to deflate.

4. To turn on the inflator, press the ON/UNIT/LIGHT button. If it does not work, the inflator will be turned off
automatically 90 seconds later.

5. When the inflator is on, press the ON/UNIT/LIGHT button to turn on the backlight in order to read the pressure in
dark. The backlight will diminish automatically in 5 seconds. Backlight will not be activated by turning on the inflator,
can only be activated by pressing the ON/UNIT/LIGHT button.

6. To change unit, when the inflator is on, press ON/UNIT/LIGHT button for at least 3 seconds. Then, press
ON/UNIT/LIGHT button shortly after to choose the desired unit. The unit chosen will be set as default

for following usage.

7. The inflator’s battery is CR2450, 2.4-3.6VDC, if the voltage is below 2.4V, the low battery signal on the top left of the
LCD display will be flashing continuously to remind user to change the battery.

8. The measuring range is 0.2~12 bar (3~175psi). Reading Accuracy is 0.01 bar (0.1psi). Maximum inlet pressure is
15 bar (218psi).

Usage Notes:

- Inflator's working pressure is 0.2~12bar (3~175psi), Max Inlet Pressure is 15bar (218psi).

- If the pressure is between 7bar and 17 bar, the actual value will still be shown on the LCD, but the Maximum
Permit table Error +/- 3psi is not guaranteed.

- Maximum Pressure is above 17bar, the LCD will show "----", no actual value, and the inflator may be damaged.

Accuracy is as below according to European Community Council Directive 86/217/EEC
±0.08bar (±1.2psi) up to and including 4bar（58psi)
±0.16bar (±2.3psi) between 4BAR（58psi) and 10bar （145psi）inclusive
±0.25bar (±3.6psi) between greater than 10bar (145psi）

1.

Unscrew with

Phillips head screwdriver

4.

IMPORTANT

To avoid the risk of personal injury, especially to the eyes, face or skin,

DO NOT direct the stream at any person.

BATTERY INSTALLATION INSTRUCTION

2.

Open LCD panel

with flat screwdriver

5.

3.

Install battery

Install the LCD panel

Tighten the screws

Page 2