Astro 1869 User Manual
1869
Normal use of this product is likely to expose
•
the user to dust and/or microscopic particles
containing chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm. Always wear
appropriate safety equipment and clothing when
using this product. Study, understand and follow
all instructions provided with this product.
1" HEAVY DUTY AIR IMPACT WRENCH
with 6" Anvil
ww w.astrotools.com
•
Always wear ANSI approved goggles when using
this product.
•
Always select the correct accessories of the
correct size and design for the job that you are
attempting to perform.
•
Always work in a clean, safe, well-lit, organized
and adequately equipped area.
Do not begin repairs without assurance that
•
vehicle is in secure position, and will not move
during repair.
Product Information:
• Ideal for tire work on trucks, buses and off-road, farm equipment
• "Pin-less" impact mechanism submits brute force strike
with low vibration
• 6" anvil makes tool perfect for the demanding world
of truck tire service
• Six-position power management/regulator
(3 forward & 3 reverse)
• Air Inlet with 45 degree angle
• Air Exhaust - Upward (away from work piece)
• Swept-back side handle & protective rubber boot
Unpacking
When unpacking, check the parts diagram and part number
listing on page 2 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Always wear ANSI approved safety goggles when using this product.
Normal use of this product is likely to expose the user to dust and/or
microscopic particles containing chemicals known to the Sate of
California to cause caner, birth defects or other reproductive harm.
Always wear appropriate safety equipment and clothing when using
this product. Study, understand, and follow all instructions provided
with this product.
SPECIFICATIONS
Working Torque Range: 300-1400 ft/lbs (408-1904 NM)
Max. Torque: 1800ft/lbs (2448NM)
Blow per minute: 750
Free Speed: 5000rpm
Recommended Air Pressure: 90psi (6.35kgs)
Air Inlet: 1/2" NPT
Minimum Hose Size: 1/2" I.D.
Overall Length: 20.1" (510mm)
Weight: 27lbs (12.3kgs)
Important
1869
(B)
1" HEAVY DUTY AIR IMPACT WRENCH
with 6" Anvil
1868-1
1868-2
1868-3
1868-4
1868-5
1868-6
1868-7
1868-8
1868-9
1868-10
1868-11
1868-12
1868-13
1868-14
1868-15
1868-18
1868-19
1868-20
1868-21
1868-22
1868-23
1868-24
1868-25
1868-26
Trigger Handle Assembly
Plunger Bushing
Reverse Valve Bushing
Inside Trigger
Pin
Spring Pin
Slot Cover
Throttle Valve
Throttle Valve Plunger
Throttle Valve Spring
Angle Inlet Bushing
Reverse Valve Knob
Ball
Protective Rubber Boot
O-Ring
Spring Pin
Spring Pin
Spring
Spring Pin
Handle Gasket
Handle Cap Screw
Lock Washer
Motor Housing
Bearing
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
8
8
1
1
2
1868-27
1868-28
1868-29
1868-30
1868-31
1868-32
1868-33
1868-34
1868-35
1868-36
1868-37
1868-38
1869-39
1868-40
1868-41
1868-43
1868-44
1868-45
1868-46
1868-47
1868-48
1868-49
1868-50
1868-51
Rear End Plate Assembly
Spring Pin
Rotor
Vane
Cylinder Assembly
Spring Pin
Front End Plate
Bearing
Hammer Frame
Hammer Cam
Hammer
Side Plate
6” Anvil
Screw
Retainer Ring
Hammer Case Assembly
Hammer Case Bushing
Oil Seal
Protective Rubber Boot
Hammer Case Gasket
Dead Handle Cap Screw
Handle Grip
Swept Back Handle
Screw Lock Washer
1
1
1
6
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
4
1
1
1
Loading...