Page 1
W
ASSEMBLING ＆ INSTALLATION INSTRUCTIONS
ARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING THE FIXTURE (Fig.2)
1. Shut off the power at the fuse box or circuit breaker. If
2. Carefully unpack the new fixture and lay all the parts on a clear
3. Attach the loop (J) to the column (K) by turning it clockwise
4. Attach the column (K) to the fixture body (P) by turning it
5. Hook the end of
6. Hook the end of
HANGING THE FIXTURE (Fig.1)
7. Thread the nipple (C) into the loop (F) until snug.
8. Thread the other end of the nipple (C) with the loop attached into
9. Place the lock washer (B) over end of the nipple (C) protruding
10. Take the crossbar assembly and mount to ceiling junction box
11. Use proper chain pliers to open one end link of the chain and
12. By measuring, determine correct number of links needed for
13. Lace the fixture wires through the chain.
14. Slip loop collar (I) and the canopy (G) and the
15. Open the other end link of the chain and hang the fixture on the
16. Feed the fixture wires through th e loop (F) and nipple (C) and
CONNECTING THE WIRES (Fig.3)
17. Connect the electrical wire as shown in figure 3, making sure
COMPLETING THE INSTALLATION (Fig.1 and Fig.2)
18. Raise the canopy (G)
19. Place the tube (M) over the socket of the arm (O).
20. Hang the crystals (N) to the top loop of the arm (O). Hang the
21. Hang the crystal (Q) to the bottom of the fixture body (P).
22. Install the light bulbs (not included) in accordance with the
Your installation is now complete. Return power to the junction box
and test the fixture.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJ O NCTEUR.
necessary, remove the old fixture, including the mounting
hardware.
area. Take care not to lose any parts necessary for installation.
until tight.
clockwise until tight.
crystals
(L) to the top loop of the fixture body (P)
and the bottom loop of the arm (O).
crystals
(L) to the loop of the
top loop of the arm (O).
the crossbar (D) until snug.
through the crossbar and thread the hex nut (A) onto the nipple
until tight.
with the junction box screws (E). Tighten the screws securely
with a screwdriver.
connect it to the fixture loop (J); then close the link.
proper hanging height. Using proper chain pliers to disconnect
and discard remaining chain.
chain.
loop at the ceiling. Close the link.
pull until tight.
that all wire connectors are secured. If your outlet has a ground
wire (green or bare copp er), connect the fix tures ground wire to
it. If the junction box has no ground wire, attach the bar e copp er
fixture w ire to th e green groun d screw on the cro ssbar. Tuck the
wire connections neatly into the ceiling junction box.
and the
column (H) all the way to the
ceiling; then raise the loop collar (I) and thread into ceiling loop
protruding through canopy.
crystals (R) to the loop of the column (H).
fixture’s specifications: DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!)
column (K)
column (H)
and the
over the
Fig.1
Fig.2
Fig.3
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare Copper(Ground)
Loading...