ASTEL LIGHTING VOLCANO Operating Instructions Manual

VOLCANO
INGROUND LED LIGHT
Operating Instructions
2
CONTENTS
Preface ...............................................................................................................................................................3
Features .............................................................................................................................................................3
Precautions ........................................................................................................................................................3
Components .......................................................................................................................................................4
Assembling and Installation ...............................................................................................................................6
Connection .........................................................................................................................................................7
Controls ..............................................................................................................................................................8
Technical Specifications ...................................................................................................................................10
Warranty ...........................................................................................................................................................14
Declaration of Conformity .................................................................................................................................15
_________________________________________________________________________________
3
PREFACE
The VOLCANO series of modular outdoor light with built-in driver is designed to use the latest LED lighting technology. The modular designed casing enables the selection of different light engines and beam angles. The VOLCANO series is available in modular stainless steel casings with PMMA or tempered glass lighting windows. The lighting is available in warm white, daylight white, cool white, red, green, blue, RGB or RGBW colors with 1, 2 or 3 high-power LEDs. The most advanced engine with built-in microprocessor enables network connection and simple control of complete groups of single-color or multi-color lights through the complete rainbow spectrum by using optional momentary switch or optional DMX512 interfaces with built-in ASTEL protocol.
FEATURES
Modular Stainless Steel Casing with PMMA tube
Sand-Blasting Finishing
1, 2 or 3 High-Power LEDs Design
Warm White, Daylight White, Cool White,
Red, Green, Blue, Multi-Color RGB or Multi-Color RGBW Lighting
High Grade PMMA or Tempered Glass Optical Window
Vacuum Metalized Reflector
Remote Control
Digital Dimming
Built-in ASTEL Protocol for DMX512
Control
Polarity Protection
Transient Protection
Thermal Protection
Low Power Consumption
Simple Installation
PRECAUTIONS
The inground light has to be installed and used in accordance with the instructions of this manual only.
The power supply has to be disconnected before installation.
Avoid using this unit near appliances generating strong magnetic fields.
The optical window has to be cleaned with a mild soap or detergent and lukewarm water by using a soft cloth or sponge. Do not use abrasive or highly alkaline cleaners. Never scrape with razor blades or other sharp instruments. Benzene, leaded gasoline, acetone or carbon tetrachloride should never be used.
Do turn power off immediately and refer servicing to qualified service personnel if the interior & exterior light does not operate normally following the operating instructions.
4
COMPONENTS
1
2 3
(1) Engine assembly
LED lighting assembly built-in sand-blasted anodized aluminium casing with different lighting color, power and beam options.
Code 1
Color of lighting
ENGWW
Warm White
ENGDW
Daylight White
ENGCW
Cool White
ENGR
Red
ENGG
Green
ENGB
Blue
ENGRGB
Red + Green + Blue
ENGRGBW
Red + Green + Blue + Warm White
Code 2
No. of LED
1
1 LED
2
2 LEDs
3
3 LEDs
4
3 High-Intensity LEDs
5
3 High-Intensity LEDs
Code 3
Beam
N
Narrow
M
Medium
W
Wide
5
(2) Inground beam assembly
Sand-blasted stainless steel assembly for direct or reflective spreading of lighting in different angles.
Code
Description
IGBDSS
Direct no reflective beam, Stainless steel, Sand-Blasted
IGBR120SS
Reflective beam 120 degrees, Stainless steel, Sand-Blasted
IGBR240SS
Reflective beam 240 degrees, Stainless steel, Sand-Blasted
IGBR360SS
Reflective beam 360 degrees, Stainless steel, Sand-Blasted
IGBDSB
Direct no reflective beam, Stainless steel, Black-Nitride
IGBR120SB
Reflective beam 120 degrees, Stainless steel, Black-Nitride
IGBR240SB
Reflective beam 240 degrees, Stainless steel, Black-Nitride
IGBR360SB
Reflective beam 360 degrees, Stainless steel, Black-Nitride
IGBDAN
Direct no reflective beam, Aluminium, Neutral Anodized
IGBR120AN
Reflective beam 120 degrees, Aluminium, Neutral Anodized
IGBR240AN
Reflective beam 240 degrees, Aluminium, Neutral Anodized
IGBR360AN
Reflective beam 360 degrees, Aluminium, Neutral Anodized
IGBDAB
Direct no reflective beam, Aluminium, Neutral Anodized
IGBR120AB
Reflective beam 120 degrees, Aluminium, Neutral Anodized
IGBR240AB
Reflective beam 240 degrees, Aluminium, Neutral Anodized
IGBR360AB
Reflective beam 360 degrees, Aluminium, Neutral Anodized
(3) Inground niche assembly
The basic component for build-in the light engine produced of stainless steel sand-blasted casing and PMMA tube.
Code
Description
IGNS
Inground niche, Stainless steel, Sand-Blasted
IGNSB
Inground niche, Stainless steel, Black-Nitride
IGNAN
Inground niche, Aluminium, Neutral Anodized
IGNAB
Inground niche, Aluminium, Black Anodized
6
ASSEMBLING AND INSTALLATION
The modular INGROUND LED light VOLCANO series consists of the following assemblies:
Engine assembly
Inground beam assembly
Inground niche assembly
The assembling and installation have to be realized by qualified personnel. The VOLCANO has to be assembled and fixed as shown in the drawing below:
a) Insert the connection cable and build-in the Inground niche assembly to the ground. b) Connect the power supply and control wires c) Tighten the Engine assembly to the Inground beam assembly d) Fix the jointed Engine assembly/Inground beam assembly to the fixed Inground niche
assembly by using of 3 enclosed screws M4
Note:
Do not overtighten the screws as this can result in inground light damage.
7
Note:
Do not cover the inground light body with any kind of temperature isolating material.
The inground light is protected by a temperature sensor against over-heating. When the temperature of the inground light exceeds 85°C the inground light is automatically switched off.
CONNECTION
The power supply has to be connected through the main switch (not included) with correct polarity and protected by a fuse (not included). The power supply voltage range has to be from 10 – 30 Vdc.
Note:
The power supply has to be switched off before installation.
The light engine has to be connected as described in the table below:
ENGINE
wire color
FUNCTION
Brown
+ DC Power Supply
Black
GND Power Supply
Red
Control
For basic control of the light the CONTROL wire has to be connected through the momentary switch (not included) to the GND by using a 2-pole signal cable extension. (not included) For DMX512 control optional LXU01 or LXU03 interface can be connected to the CONTROL and GND wires by using a 2-pole signal cable (not included).
Note:
When two or more lights are connected in the lighting system the control wires (red) can
be connected in parallel and all the lights then can be controlled by using only one momentary switch or LXU01 (LXU03) interface.
Earthing
The inground light has to be earthed by using a pre-tinned green wire with a yellow stripe a minimum of 8 AWG (8.36 mm2). The wire has to be connected to the path light by the help of one fixing screw M8x60
Synchronization
When more than one light is connected to the system the optional Synchronization Unit LSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting. On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode. If the multi-color RGB light is used only with one of the fixed color of lighting the synchronization is not necessary.
8
CONTROLS
Single-color warm white (ENGWW), daylight white (ENGDW), cool white (ENGCW), red (ENGR), green (ENGG) or blue (ENGB) models:
Control by momentary switch
Remote control by momentary switch can be used to turn-on and turn-off the light and to control the luminosity.
Turning on / off Press the momentary switch momentary.
Dimming When the light is on, press the momentary switch longer until the desired power is achieved.
Turning on minimum When the light is off, press the momentary switch longer (e.g. one second or more) until the light is turned on at minimum power.
Set default Press the momentary switch for min. 40 seconds or until the light is turned off.
DMX512 control
The network connection to control the light with the standard DMX512 protocol is enabled by using optional LXU01 or LXU03 interfaces.
Multi-color (ENGRGB) model:
Control by momentary switch
Remote control by momentary switch has to be used to turn-on and turn-off the light and to control the mode of lighting and luminosity. When the light is turned-off the color or mode of lighting can be changed sequentially by pressing the momentary switch for 2 seconds:
ENGRGB
Sequence of lighting
Custom Color
Full RGB
Cool White
Bluish White
Red
Green
Blue
Rainbow Color Spectrum
Turning on /off Press the momentary switch shortly.
Changing the color or mode of lighting When the light is turned-off press the momentary switch for 2 seconds.
9
Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected.
Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity will increase to the maximum illumination.
Set default Press the momentary switch for min. 40 seconds or until the light is turned off.
DMX512 control
The built-in ASTEL protocol enables the network connection to control the lights with the standard DMX512 protocol by using optional LXU01 or LXU03 interfaces.
Multi-color (ENGRGBW) model:
Control by momentary switch
Remote control by momentary switch has to be used to turn-on and turn-off the light and to control the mode of lighting and luminosity. When the light is turned-off the color or mode of lighting can be changed sequentially by pressing the momentary switch for 2 seconds:
ENGRGBW
Sequence of lighting
Custom Color
Full RGB
Cool White
Bluish White
Red
Green
Blue
White Color Spectrum
Custom White Color
Rainbow Color Spectrum
Turning on /off Press the momentary switch shortly.
Changing the color or mode of lighting When the light is turned-off press the momentary switch for 2 seconds.
Setting the Custom White Color At the selected White Color Spectrum mode press the key-switch momentary to turn the light off. After that press the key switch for 5 seconds or until the light is switched to the selected white color and then the White Color is set and selected.
Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected.
10
Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity will increase to the maximum illumination.
Set default Press the momentary switch for min. 40 seconds or until the light is turned off.
DMX512 control
The built-in ASTEL protocol enables the network connection to control the lights with the standard DMX512 protocol by using optional LXU01 or LXU03 interfaces.
TECHNICAL SPECIFICATIONS
Engine assembly
Power supply 12 – 24 Vdc, max. 260 mA/12 Vdc or 135 mA/24 Vdc (1 LED)
12 – 24 Vdc, max. 500 mA/12 Vdc or 260 mA/24 Vdc (2 LEDs) 12 – 24 Vdc, max. 800 mA/12 Vdc or 420 mA/24 Vdc (3 LEDs)
12 – 24 Vdc, max. 950 mA/12 Vdc or 500 mA/24 Vdc (3 High-Int. LEDs) 15 – 24 Vdc, max. 1.200 mA/24 Vdc (3 High-Int. LEDs) 12 – 24 Vdc, max. 600 mA/12 Vdc or 300 mA/24 Vdc (RGB) (N) 12 – 24 Vdc, max. 650 mA/12 Vdc or 350 mA/24 Vdc (RGB) (M/W) 12 – 24 Vdc, max. 800 mA/12 Vdc or 400 mA/24 Vdc (RGBW) (N) 12 – 24 Vdc, max. 650 mA/12 Vdc or 350 mA/24 Vdc (RGBW) (M/W) Beam angle 12°(N), 30°(M), 80°(W) (1 LED)
20°(N), 36°(M), 120°(W) (2 LEDs) 12°(N), 30°(M), 80°(W) (3 LEDs) 15°(N), 40°(M), 120°(W) (RGB) 15°(N), 40°(M), 120°(W) (RGBW)
Optical window High-grade polycarbonate glass Luminous flux (cool white) max. 250 lm (1 LED) max. 500 lm (2 LEDs) max. 700 lm (3 LEDs) max. 1.400 lm (3 High-Intensity LEDs) max. 3.000 lm (3 High-Intensity LEDs) max. 190 lm (RGB) (N) max. 400 lm (RGB) (M/W) max. 330 lm (RGBW) (N) max. 550 lm (RGBW) (M/W) Operating temperature -10°C - +40°C Casing Anodized aluminium Protection IP 67 Dimensions Ø86 x 68 mm (ordering code 2: 1, 2, 3, 4) Ø86 x 153 mm (ordering code 2: 5) Weight 0.6 kg (ordering code 2: 1, 2, 3, 4)
1.7 kg (ordering code 2: 5)
11
Inground beam assembly
Material Stainless steel (SAE316L) or Aluminium with PMMA or
tempered glass Dimensions Ø110 x 27 mm (IGBD) Ø110 x 28 mm (IGBR) Weight 0.8 kg (IGBDSS, IGBDSB) (stainless steel) 350 g (IGBDAN, IGBDAB) (aluminium)
0.8 kg (IGBR120SS, IGBR120SB) (stainless steel) 300 g (IGBR120AN, IGBR120AB) (aluminium)
0.7 kg (IGBR240SS, IGBR240SB) (stainless steel) 250 g (IGBR240AN, IGBR240AB) (aluminium)
0.6 kg (IGBR360SS, IGBR360SB) (stainless steel) 200 g (IGBR360AN, IGBR360AB) (aluminium)
Inground niche assembly
Material Stainless steel (SAE316L) and PMMA Dimensions Ø140 x 140mm
Weight 1.2 kg (stainless steel) 500 g (aluminium)
The model specification:
VOLCANO
- - -
NICHE code ENGINE code BEAM code
Design and specifications subject to change without notice.
12
13
14
WARRANTY
1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in
workmanship and materials under normal use and service.
2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase
must be included, to establish that it is inside the warranty period.
3. This Warranty is transferrable and covers the product for the specified time period.
4. In case any part od the equipment proves to be defective, other than those parts excluded in
paragraph 5 below, the owner should do the following:
(a) prepare a detailed written statement of the nature and circumstances of the defect, to the best
of the Owner’s knowledge, including the date of purchase, the place of purchase, the name and adress of the installer, and the Purchaser’s name, adress and telephone number;
(b) the Owner should return the defective part or unit along with the statement referenced in the
preceding paragraph to the warrantor, ASTEL d.o.o., or an authorized distributor, postage/shipping prepaid and at the expense of the Purchaser;
(c) if upon the Warrantor’s or authorized distributor’s examination, the defect is determined to
result from defective material or workmanship, the equipment will be repaired or replaced at the Warrantor’s option without charge, and returned to the Purchaser at the Warrantor’s expense;
(d) no refund of the purchase price will be granted to the Purchaser, unless the Warrantor is
unable to remedy the defect after having a reasonable number of opportunities to do so. Prior to refund of the purchase price, Purchaser must submit a statement in writing from a professional supplier that the installation instructions of the Operating Instructions manual have been complied with and that the defect remains;
(e) warranty service shall be performed only by the Warrantor, or an authorized distributor, and
any attempt to remedy the defect by anyone else shall render this warranty void.
5. There shall be no warranty for defects or damages coused by faulty installation or hook-up, abuse
or misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or water immersion except for equipment specially designed as waterproof.
6. There shall be no responsibility or liability whatsoever on the part of the Warrantor or its
employees and representatives for injury to any person or persons, or damage to property, loss of income or profit, or any other consequential or resulting damage or cost which may be claimed to have been incurred through the use or sale of the equipment, including any possible failure or malfunction of the equipment, or part thereof.
15
DECLARATION OF CONFORMITY
according to IEC Guide 22 and EN 45014
Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o.
Manufacturer's Address: Dutovlje 138
6221 Dutovlje Slovenija
declares that the products
Item, Product Name and Model Number: 1. INGROUND LED light VOLCANO series
conform to the following Product Specifications:
EMC: EN 55015:2006 + A1:2007 EN 61547:1995 + A1:2000 + A2:2009 EN 61547:2009
Safety: EN 60598-2-18:1995/A1:2012 EN 60529:1992+A2:2013
Supplementary Information:
The products herewith comply with the requirements of the following Directives and carry the CE­marking accordingly:
-the Low Voltage Directive 2014/35/EU
-the EMC Directive 2014/30/EU
-the RoHS Directive (EU)2015/863
ASTEL d.o.o. Dutovlje 138 6221 Dutovlje Slovenija
18th January, 2017
16
ASTEL d.o.o., Dutovlje 138, 6221 Dutovlje, Slovenia
Tel: +386 5 7310771, +386 5 7310772
Fax:+386 5 7310789
E-mail:
info@astel-lighting.com
Web: www.astel-lighting.com
Loading...